Outdoor GreatRoom Company Cedar Bluff User manual

1
Key Largo and Cedar Bluff Fire Pits
Installation Instructions for Key Largo, all base
materials and top styles, and Cedar Bluff Fire Pit

2

3
Contents
Contents…………………………………………2
Required Tools…………………………….…..3
Placing and assembling the Table.………4
Gas Connection………………………….…….5
Igniter Installation…………….……………...6
Locating Propane tank………………………8
Finishing Touches…………………………….9
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found on the
coffee table.
One (1) AAA Battery (not included)
Required for piezoelectric igniter installation.
It is recommended that a minimum of two
people assemble and install fire pit tables.
90218: REV. I 8.20.18

4
Placing and Assembling the Fire Pit table
1. Remove access door from packaging
2. Remove all components from packaging.
3. Move the base without door to desired location and
set into place.
4. When locating your coffee table, refer to the Crystal
Fire manual and maintain clearance to combustibles.
5. Assemble as shown below.
Igniter
Igniter
*Base colors and materials may differ
depending on model

5
Gas Connection
1. Remove stainless steel top (if applicable) and lift
burner out of base to expose control valve.
2. Connect the incoming gas hose to the valve
and tighten securely. Repeat with flexible
metal gas line from the valve to the
underside of burner. It is not recommended
to use Teflon tape or pipe dope on the
connection to the valve with flare fittings.
LPG installations use the hose and regulator
provided with the burner.
For Natural Gas hookup information and
any other info not listed here consult your
Crystal Fire owner’s manual.
Attach incoming
gas here
Read and understand your Crystal Fire owner’s manual
before beginning burner hookups or using the device.

6
Igniter Installation
1. Make sure the valve is in the OFF
position
2. Unscrew sparker cap and hex nut.
Install as shown below.
AA
A

7
3. To properly install ignition system, a spark and ground wire
need to be attached to the igniter box.
Start by plugging the black wire hanging from the
burner in to one side of the back of the igniter.
Plug the included grounding wire (which arrives
attached to the underside of the burner) into the back
of the sparker box
Test system by pushing the button on the igniter. A
continuous repeating spark between the igniter
electrode and spark-receiving probe means everything
is connected properly. Consult the troubleshooting
section if spark is weak, intermittent, or not present.
4. Once ignition system is grounded and gas
connections are secured and checked for
leaks, set the burner back into its original
position and replace the top if applicable.

8
Locating your Tank
1. Your tank should be positioned so that
the fuel can be shut off after each use.
2. Slide the tank into the framework past
the line shown below. This is to allow
the door to close completely.
3. Confirm all hoses are clear and not
touching the burner.
Position tank behind this line
Install door by setting the bottom on the catching hooks first and
then closing. Magnets in the table will hold door closed.

9
Finishing touches
Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming
an even layer of beads.
DO NOT BURN WITHOUT GLASS OR OTHER
DECORATIVE SUBSTRATE PRESENT

10
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CF-1242 or CF-1224 BURNER
WITHOUT FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks