Outdoor GreatRoom Company COR-1264 User manual

1
Cortlin Fire Pit Table
Installation Instructions for Cortlin Fire Pit Table
COR-1264

2
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Two people are recommended for
this installation
Contents
Required Tools………………………………….........2
Included with your Fire Pit………………………..3
Assembly Instructions……………………………….4
CF-SPARKER Installation…………………..……….4
Gas Connections……………………………………….5
Electrode Installation…………………….………….7
Burner Installation…………….………………….…..7
Fire Media Installation……………………….……..8
Glass Cover Installation……………………………..8
Operating Instructions..……………………………..9
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42491 REV A 03-22-18

3
Included with Your Fire Pit
Cortlin 1264 base
(Control Panel Installed)
COR-1264-BASE
Two Piece Glass Cover
1264-GGC
1264 Crystal Fire Burner
CF-1264
Black Key
(BF-KY-05)
Refer to Crystal Fire Manual for items included with crystal fire burners.

4
Do not discard any packaging until assembly is complete and
unit is tested.
Keep all included manuals in a safe place for future
reference.
Place base in desired final location.
Place on a hard, flat surface. Avoid soft surfaces and areas
that collect water.
Refer to Crystal Fire Manual included with your Crystal Fire
Burner for safety information regarding the placement of
your fire pit.
Assembly Instructions
Locate CF-SPARKER inside of crystal fire burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery
(not included) with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Un-packaging
Base Placement
1.
2.
CF-SPARKER Installation
3.

5
Gas Connections
Read and understand your Crystal Fire owner’s manual before beginning burner
hookups or using the device. Do not use Teflon tape or pipe dope on flare fittings.
Natural gas supply line
as specified by local
building codes
Propane
input
Natural
gas input
• Reach inside the base and attach gas supply line to the input shown below,
using a 1/2” flare fitting. Use two wrenches to ensure a gas tight connection.
TIGHTEN CONNECTION
SECURELY WITH WRENCH
• Ensure the correct orifices are installed for the fuel type you are using
(see Crystal Fire Burner Owner’s manual included with burner for orifice
sizing information).
4.

6
Metal flex line to
burner
ONLY
TIGHTEN ALL CONNECTIONS SECURELY WITH TWO WRENCHES
• Attach flex line from the burner to gas valve as shown below.
Use two Wrenches to secure connection.
Flexline to Burner
TIGHTEN CONNECTION
SECURELY WITH WRENCH

7
Plug both BLACK wires hanging from the burner into
the back of the CF-SPARKER. If an orange wire is
present, do not use it. The orange wire is for Direct
Spark Ignition system only.
Test system by pushing the button on the igniter.
Consult the troubleshooting section of the Crystal Fire
Burner Owner’s Manual, if the spark is weak,
intermittent, or not present.
Control Panel
Electrode end of burner
Orient burner so that the electrode is nearest to the control
panel in order to make CF-SPARKER box connections.
Electrode Installation
5.
Burner Installation
6.

8
Scatter all included glass beads, lava rock, or other approved fire
media evenly across entire burner surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT INCLUDED GLASS
BEADS OR OTHER APPROVED FIRE MEDIA
• Carefully lay both pieces of the two piece glass cover on top of
burner. Make sure burner is cool before attempting to place glass
cover.
DO NOT OPERATE CRYSTAL FIRE BURNER WITH BURNER COVER IN PLACE
Fire Media Installation
7.
Glass Cover Installation
8.

9
Before operating your Cortlin 1264 fire pit, ensure all gas
connections are properly tightened and thoroughly leak checked.
Refer to the Crystal Fire Manual for information on proper leak
checking and other critical safety information.
With the valve on the fire pit in the OFF
position, open the valve on the propane tank
or natural gas supply.
Double check to make sure there are no gas
leaks at the regulator or inlet side of the
valve. If leak is detected, immediately shut off
the gas supply and wait 5 minutes to allow
gas to dissipate. Fix any leaks before
proceeding.
Press the sparker button and hold, look and
listen for spark between electrode and
grounding rod.
While depressing the sparker, open the valve.
3. Turn valve to ON
2. Look/listen for spark
1. Depress sparker
If burner does not light after 10 seconds,
close the valve and wait 5 minutes to allow
gas to dissipate before attempting ignition
again.
Refer to the Crystal Fire Manual included with your burner for
more detailed information on operation, maintenance, and safety
of your burner.
Operating Instructions
9.

10
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks