Outdoor GreatRoom Company Pointe User manual

1 | P a g e
The Pointe Fire Pit
Assembly and Operating Instructions for
The Pointe Fire Pit

2 | P a g e
Contents
Contents……………………………………………………..2
Required Tools…………………………………………..3
Placing and assembling theTable.……4
Igniter Installation…………….………………………...6
Locating Propanetank……………………………8
Finishing Touches……………………………………….9
Included Items:
Base with control
panel
Not pictured:
-Igniter module
-#21 Natural Gas orifice (x2)
-#31 Liquid Propane orifice (x2) (pre-installed)
-6-5lb bags of decorative fire gems
-Gas hose for 20lb LP Tank
–Stainless steel flex hose

3 | P a g e
Required Tools
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found
on the coffee table.
One (1) AAA Battery(not
included)
Required for piezoelectric igniter
installation.
AT LEAST two people required
for assembly
90292:C 8.20.18

4 | P a g e
Placing and Assembling the Fire Pit table
1. After removing the fire pit from packaging, move the
base without door to desired location and set into
place.
2. When locating your coffee table, refer to the Crystal
Fire manual and maintain clearance to combustibles.
3. Set the SuperCast into place on the fire pit base.
Make sure the top is centered over the opening
before proceeding.
4. Have one person hold the burner on edge in the
recessed opening, while connecting the included
flexible stainless steel hose to control valve and the
T-manifold connected to burner. Use two wrenches
to secure connection.

5 | P a g e
6. Connect incoming gas line (black rubber propane hose or
hard pipe from outside source) to the lower fitting on the
control valve, ensuring the knob is in the “OFF” position.
Carefully set burner back into place in the table top.
Attach incoming
gas here
Check system for leaks before use
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Installation should be performed by a qualified gas technician
*base shown may differ from actual product
Stainless flex
line to burner

6 | P a g e
Igniter Installation
1. Make sure the valve is in the OFF
position
2. Unscrew sparker cap and hex nut.
Install as shown below.

7 | P a g e
3. To properly install ignition system, a spark and ground wire
need to be attached to the igniter box.
Start by plugging the black wire hanging from the
burner in to one side of the back of the igniter.
Plug the included grounding wire (which arrives
attached to the underside of the burner) into the back
of the sparker box
Test system by pushing the button on the igniter. A
continuous repeating spark between the igniter
electrode and spark-receiving probe means everything
is connected properly. Consult the troubleshooting
section if spark is weak, intermittent, or not present.
4. Once ignition system is grounded and gas
connections are secured and checked for
leaks, set the burner back into its original
position .
NOTE: Orange wire hanging from burner
is not used for this installation.

8 | P a g e
Locating your Tank
1. Your tank should be positioned so that
the fuel can be shut off after each use.
2. Slide the tank into the framework past
the line shown below. This is to allow
the door to close completely.
3. Confirm all hoses are clear and not
touching the burner.
Position tank behind this line
Install door by setting the bottom on the catching hooks first and
then closing. Magnets in the table will hold door closed.

9 | P a g e
Finishing touches
Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming
an even layer of beads.
DO NOT BURN WITHOUT GLASS OR OTHER
DECORATIVE SUBSTRATE PRESENT
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CF-1242 or CF-1224 BURNER
WITHOUT FIRST CONSULTING THE MANUAL. IF YOU ARE UNSURE OF
HOW TO COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks

10 | P a g e
© 2014 The Outdoor GreatRoom Company
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]