Outdoor GreatRoom Company Kinney KN-1224 User manual

Installation Instructions for Kinney Fire Pit Table
KN-1224
Kinney Fire Table
outdoorrooms.com

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER
WITHOUT CONSULTING THE CRYSTAL FIRE®PLUS
OWNER’S MANUAL.
CONTENTS
1. About Your Fire Table 2
a. Required Tools
outdoorrooms.com42507 REV C 01-16-20
!!
1
b. Included With Your Fire Pit
2. Assembly Instructions
a. Unpacking
b. CF-SPARKER Installation
3. Setting Up Your Burner
a. Gas Connections
b. Electrode Installation
c. Propane Tank Installation
4. Miscellaneous
a. Fire Media Installation
b. Glass Cover Installation
5. Operating Instructions
6. Warnings
3
4
7
9
10
c. Burner Cover Storage

outdoorrooms.com 2
• Utility Knife -
To cut and remove packaging
• 2 Open Ended Wrenches -
To secure gas connections
•Phillips Screw Driver (Do not use a drill to assemble) -
For assembly
• One AAA Battery (Not Included)-
Required for electric spark igniter installation
1. ABOUT YOUR FIRE TABLE
Burner Cover
(1)
Fully Assembled Kinney Fire
Table with CFP1224 Burner
(1)
A. REQUIRED TOOLS
B. INCLUDED WITH YOUR FIRE PIT
Bags of Glass Beads(2)
Control Valve Knob and
Sparker
IMPORTANT
Standard LP tank will not t under table. A special horizontal LP tank
can be purchased to t.
STANDARD TANK CAN BE USED, MUST BE KEPT OUTSIDE OF TABLE.
DO NOT TIP STANDARD 20 LBS. TANK ON SIDE.
!!

outdoorrooms.com 3
ASSEMBLY INSTRUCTIONS
•Do not discard any packaging until assembly is complete and unit is tested.
•Keep all included manuals in a safe place for future reference.
•Two people are recommended to remove table from packaging.
•Place table in desired location before installing control valve and gas
connection.
Exposed edges may be sharp, use leather gloves
when removing packaging and handling the base.
2.
!!
CF-SPARKER
A. UNPACKING
B. CF-SPARKER INSTALLATION
CONTROL PANEL
WARNING
• Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included)
with + end out.
• Unscrew mounting screws from control valve. Install CF-SPARKER
on to control panel as shown below. Reconnect mounting screws and
control valve to control panel.
• Press in CF-SPARKER button to test your sparker.
CONTROL VALVE

outdoorrooms.com 4
SETTING UP YOUR BURNER
ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before
beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
3.
•For hard piped installations. Connect the gas supply line (not included) to the
3/8” male are tting on the valve.USE TWO WRENCHES TO ENSURE A GAS
TIGHT CONNECTION.
•Run gas pipe up through the opening between the 2 base plates as shown in
the image below.
!
!
A. GAS CONNECTIONS
•See Crystal Fire®Plus instructions for burner installation.
• All gas connections were completed at the factory.
• Check all connections for leaks. If needed, tighten connection with 2 wrenches
and re-check for leaks.
• Attach included control valve knob to control valve stem.

outdoorrooms.com 5
B. ELECTRODE INSTALLATION
• Plug both BLACK wires hanging from the burner into the back of the
CF-SPARKER. If an orange wire is present, DO NOT USE IT. The orange wire is
for Direct Spark Ignition system only.
• Test system by pushing the button on the igniter. Consult the troubleshooting
section of the Crystal Fire® Plus owner’s manual if the spark is weak, intermit-
tent or not present.

outdoorrooms.com 6
C. PROPANE TANK INSTALLATION
HAND TIGHTEN, DO NOT USE A
WRENCH FOR THIS CONNECTION.
!!
• Remove door on front side of
table
• Pull out tank drawer.
• With the propane tank valve
and re pit valve o, attach the
propane regulator to the propane
tank.
• Place tank in tank tray.
•Slide tank drawer in. Ensure no
hoses or wires are contacting the
bottom of the burner.
• Replace the access door.
ACCESS DOOR
ATTENTION
Over time the bearings in the door
glides may require re-greasing. Any
spray lubricant, such as WD-40,
may be used to lubricate drawer
glides. Perform annually or on an
as needed basis to maintain smooth
operation.
! !
ATTENTION
PROPANE REGULATOR
HORIZONTAL PROPANE TANK
(DO NOT TIP STANDARD TANK ON SIDE)
STANDARD LP TANK WILL NOT
FIT IN BASE. STANDARD LP TANK
MUST SIT OUTSIDE OF BASE.
DO NOT TIP STANDARD LP TANK
ON ITS SIDE
Tanks under 14 inches can be used
within table but must be kept upright
and not on their side.
!! ATTENTION

outdoorrooms.com 7
A. FIRE MEDIA INSTALLATION
B. BURNER COVER INSTALLATION
•Scatter all included glass beads, lava
rock, or other approved re media
evenly across entire burner surface.
WARNING
DO NOT OPERATE CRYSTAL FIRE®
PLUS BURNER WITHOUT INCLUDED
GLASS BEADS OR OTHER APPROVED
FIRE MEDIA.
WARNING
DO NOT OPERATE CRYSTAL FIRE®
PLUS BURNER WITH BURNER
COVER IN PLACE.
4. MISCELLANEOUS
!
!
!
!
•Fully shut o gas supply to table and
turn control valve knob to OFF position.
Wait for burner to become cool before
placing cover.
• Carefully place the cover on top of the
burner.
•Remove burner cover before
attempting ignition.

outdoorrooms.com 8
ATTENTION
If burner cover needs to be replaced,
the grain on the cover and top may
vary from the original cover. This is
due to the “one of a kind” nature of
the table surface
!!
C. BURNER COVER STORAGE
ATTENTION
Use caution when removing
and placing the
burner cover as to not chip or
damage the edge.
!!
When not in use, Burner cover can be
conveniently stored within table.
•Remove door on back end of table.
• Lay burner cover at and slide
inbetween the two guides. Push cover
in enough so that door will not interfere
with it once replaced.
• Replace door.

outdoorrooms.com 9
OPERATING INSTRUCTIONS5.
IMPORTANT
Before operating your KN-1224, ensure all gas connections are properly tight-
ened and thoroughly leak checked. Refer to the Crystal Fire®Plus manual for
information on proper leak checking and other critical safety information.
!
!
!
!
FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a re or explosion may result causing
property damage, personal injury, or loss of life.
Verify control valve is in OFF position. If operating on a self-contained propane
cylinder, ensure cylinder valve is CLOSED. If operating on a hard-piped system,
ensure main gas supply shut-o valve and all other valves in gas system are
OPEN.
If operating on a self-contained propane cylinder, slowly open cylinder valve.
Press and hold sparker button. Verify an audible and visible spark is present
within the ignition wind guard.
Gently press and turn control knob to LOW/IGNITION position. Fully depress
control knob and hold for 3-5 seconds. Burner should ignite and continue to
operate when control knob is released.
If burner does not light or remain lit after 20 seconds of attempting ignition, turn
control valve to OFF position and wait 5 minutes to allow gas to dissipate before
attempting ignition again. DO NOT ATTEMPT TO LIGHT BURNER IF YOU SMELL
GAS.
With burner lit and operating, the ame height can be adjusted between LOW
and HIGH at any time.
WARNING
OFF
LOW/
IGNITION
HIGH
PUSH AND HOLD
TO IGNITE
DEPRESS SPARKER
BUTTON
SEE DETAIL B
LOOK FOR SPARK
HERE
OFF
LOW/
IGNITION
HIGH
PRESS AND HOLD
SPARKER BUTTON
ROTATE COUNTER-CLOCKWISE
TO LOW AND SLOWLY DEPRESS
HOLD KNOB IN FOR 3-5 SECONDS