Outdoor GreatRoom Company Marquee Fire Pit Table User manual

1
Marquee Fire Pit Table
Installation Instructions for Marquee fire pit
.
.
.
.
.
.
.
.
.
.

2
Contents
Required Tools…………………………….…….2
Assembly Instructions………………..………3
Gas Connection………………………….………4
Igniter Installation…………….……………....6
Glass Installation………………………………..7
Position Your Propane tank………………..8
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from rough edges found on
coffee table during installation.
One AAA battery (not Included)
Required for electric spark igniter installation
Power Drill with #2 Phillips Tip Bit
To open the crate for access to fire pit
Phillips Screw Driver
To fasten bolts to the burner
Four people are required for this
installation
42446 REV B 8.3.16

3
Assembly Instructions
1. Open the crate and remove all pieces. Components
may be heavy and require the assistance of 3 other
people helping to set them in the desired location.
2. Set the base in the desired location and place the
concrete top onto the base.
3. Align holes from burner pan to burner tray.
Fasten the burner to the burner pan using the 6
nuts and bolts included with your fire pit.

4
Gas Connections
1. Reach inside the burner cut-out and attach natural gas supply
line using a 3/8” flare fitting, or attach the included black
rubber propane hose and regulator to the bottom fitting of the
control valve.
TIGHTEN SECURELY WITH A WRENCH
2. Lay the burner upside down on a flat, soft surface to avoid
scratching the polished metal. Ensure the correct orifice is
installed for the fuel type you are using (see Crystal Fire user
manual included with burner for orifice sizing information)
Attach the included metal flex hose to the burner.
TIGHTEN SECURELY WITH TWO WRENCHES
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Propane input
Natural gas input
or
Natural gas supply line
as specified by local
building codes

5
Igniter
Igniter
Metal flex line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH
3. Set the burner into the fire pit exactly
as shown, with igniter on the left and
above the control panel. Make final gas
connection to the control panel.
IGNITER

6
Igniter Installation
1. Make sure the valve is in the OFF
position before beginning.
2. Install sparker as shown, using an
AAA battery (not included). Negative
end should be placed inside the CF-
SPARKER, positive end on the outside
of CF-SPARKER.
Sparker will not operate correctly without an ignition and ground
wire attached.
Plug both BLACK wires hanging from the burner into
the back of the sparker box. If an orange wire is
present, do not use it. Orange wire is for automatic
ignition system add-on only.
Test system by pushing the button on the igniter.
Consult the troubleshooting section if spark is weak,
intermittent, or not present.

7
After installing igniter and making gas connections, verify that
they are tight and that no leaks are present using a solution of
soapy water or a commercially available leak-check solution.
Glass Installation
1. Scatter the included glass beads evenly on to the
burner surface using all of the beads that came
with the fire pit. DO NOT BURN WITHOUT GLASS
OR OTHER DECORATIVE MEDIA PRESENT.
2. With concrete top on base, locate 3 glass pieces
that were included with your fire pit. Attach
bumper pads to textured side of glass pieces.
Attach 1 bumper bad to each of the corners, of
each glass piece. Set glass pieces into the 3 pre-
cut openings, with silicon pads facing downward.
Burner cover with finger holes will sit on top of
burner pan, the separate 2 solid glass covers will
sit in outside openings.
Position Your Tank
(if applicable)

8
1. Remove door, connect the propane hose/regulator to the propane
tank and hand-tighten (DO NOT USE A WRENCH) and slide the
propane tank in completely to ensure the door closes properly.
2. With tank inside base, ensure that no hoses, wires, or anything else
is kinked or touching the burner pan.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL NF-7X19 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
Warranty: Fire pit tables are covered under a 1-year manufacturer’s warranty.
Please visit http://www.outdoorrooms.com/warranty-form to register your
product.
Position Your Propane Tank
(If Applicable)
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]