Outdoor GreatRoom Company BRK-1224 User manual

1
Brooks Fire Pit Table
Installation Instructions for Brooks Fire Pit Table
BRK-1224 and BRK-2424

2
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Phillips Screwdriver
To attach mounting screws to control panel
Two people are required for this
installation
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
REV G 12-20-19
Contents
Required Tools…………………………………................2
Included with your Fire Pit……………………….……..3
Assembly Instructions…………………………….…..….4
CF-SPARKER Installation …………………………..…...6
Gas Connections…………………………………………….7
Thermocouple Installation……………………………..8
Electrode Installation………………………………….....8
Fire Media Installation……………………………………9
Position Your Tank……………………………………….10
Riser Kit Installation…………………………………..…11

3
Optional Riser Kit:
Required to fit 20# propane tank
under table
Included with your Fire Pit
Panel C [X1]
M6 Allen
Wrench [X1]
Bolt Caps
[X4]
TOUCH
UP
PAINT
M6X20
Panel B [X1]
Access Door [X1]
Top
Center Support [X2]
Bolt A [X16]
Gas Valve Kit
Gas Valve [X1]
Mounting
screws [X2]
Control knob
[X1]
CFP1224/CFP2424 Burner
Panel A [X1]
Touch-Up
Paint Bottle
[X1]

4
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
55
1. Unpack contents from box, and remove individual packaging from each
piece.
2. Lay Side Panel with Control Panel on soft, flat surface.
3. Position Support Piece on the Side Panel. NOTE: It is very important to
positon the Support Piece as shown in the picture below, to ensure that
your burner and propane tank fit correctly with your fire pit table base.
Assembly Instructions
INSTALL NOTE: Final tightening of bolts should be completed following
installation of all panels.
1. Unpack all the contents from the box and remove the individual
packaging from each component. Remove 4 pre-installed bolts (Bolt A)
from the underside of the Top.
2. Carefully lay the Top, with underside facing upwards, on a soft and flat
surface. Attach Panel A using Bolt A (x2) as shown below.
3. Attach Panel B on the opposite side of Panel A using Bolt A (x2)
as shown below.

5
4. Attach Panel C using Bolt A (x4) as shown below.
A
5. Attach a Center Support piece,
as shown below, to the bottom
of the fire pit using Bolt A (x4).
NOTE: Drainage holes on
Center Support piece must be
facing down towards the
surface on which you will be
placing your fire pit.
6. Attach a second Center Support
piece to the top of the fire pit, on the
opposite side from Panel C, using Bolt A
(x4).
.
.
.
.
.
.
.
.
NOTE: Drainage holes on
Panel C must be facing
down towards the surface
on which you will be
placing your fire pit.
Drainage holes

6
7. Do a final tightening of the bolts you have installed in your fire pit.
Then, with the help of another person, turn the table right side up.
.
CF-SPARKER Installation
Locate CF-SPARKER inside of Crystal Fire Plus burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery
(not included) with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.

7
Gas Connections
Read and understand your Crystal Fire Plus owner’s manual
before beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
See Crystal Fire Plus instructions for burner installation.
All gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection with
2 wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as shown
below. Ensure sparker box is installed before this step.
Insert screws
included with
Gas Valve Kit

8
Thermocouple Installation
•Refer to Crystal Fire Plus instruction manual for detailed attachment of
thermocouple.
•Attach thermocouple to burner valve as shown below.
Electrode Installation
Plug both BLACK wires hanging from the burner into the back of the
CF-SPARKER. If an orange wire is present, do not use it. The orange
wire is for Direct Spark Ignition system only.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire Plus Burner Owner’s
Manual, if the spark is weak, intermittent, or not present.

9
Fire Media Installation
1. Scatter all of the included Glass Beads evenly onto burner
surface.
DO NOT OPERATE CRYSTAL FIRE PLUS BURNER WITHOUT GLASS
BEADS OR OTHER DECORATIVE MEDIA PRESENT
DO NOT OPERATE CRYSTAL FIRE PLUS BURNER WITH GLASS COVER
IN PLACE (NOT INCLUDED)

10
After installing igniter and making gas connections, verify that
all connections are tight and that no leaks are present using a
solution of soapy water or a commercially available leak-check
solution.
Position Your Tank
(if applicable)
1. Connect the propane hose/regulator to the propane tank and
hand tighten (DO NOT USE A WRENCH) and slide the propane
tank past the dotted line to ensure the Access Door closes
properly. Attach the Access Door.
2. With the tank inside, ensure that no hoses, wires, or any other
components are kinked or touching the burner pan.