Outdoor GreatRoom Company CV-30-E User manual

1
The Cove Fire Pit
Installation Instructions for Round Cove Fire Pits

2

3
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from rough edges
found on fire pit table during
installation.
One AAA battery (not Included)
Required for electric spark igniter
installation
Two people are required for this
installation
Required Tools
Two people are required for this installation.
2 Open Ended Wrenches
To secure gas connections.
Leather Gloves
To protect hands from rough edges found on fire pit
during installation.
One AAA Battery (not included)
Required for electric spark igniter installation.
Utility Knife
To cut and remove packaging.
Power Drill
To remove support board from crate.
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42467 REV D 04-19-21
Contents
Required Tools………………………………….........3
Included with your Fire Pit………………………..4
Assembly Instructions……………………………….5
CF-SPARKER Installation…………………………...6
Gas Connections……………………………………….6
Thermocouple Installation……………………..…7
Electrode Installation………………………………..7
Glass Installation………………………………………8
CV-30-E Installation………………………….………9

4
Crystal Fire® Plus (CFP) Burner Kit
Included with your Fire Pit

5
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
Assembly Instructions
1. First, unscrew the shipping block with a power drill. Discard
board. It will not be needed for further assembly of this
product.
2. Remove fire pit base from the crate you received it in. Place
the base in your desired location. Two people are
recommended for this step of the installation.
1
2
.
.
Shipping Block

6
CF-SPARKER Installation
Gas Connections
Read and understand your Crystal Fire® Plus Burner Owner’s
manual before beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Locate CF-SPARKER inside of crystal fire burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery
(not included) with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.
See Crystal Fire® Plus instructions for burner installation.
All gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection
with 2 wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as
shown below. Ensure sparker box is installed before this step.

7
Thermocouple Installation
•Refer to Crystal Fire® Plus instruction manual for
detailed attachment of thermocouple.
•Attach thermocouple to burner valve as shown below.
Electrode Installation
Plug both BLACK wires hanging from the burner into the back
of the CF-SPARKER. If an orange wire is present, do not use it.
The orange wire is for Direct Spark Ignition system only.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire® Plus Burner
Owner’s Manual, if the spark is weak, intermittent, or not
present.

8
1. Scatter all the included glass beads evenly onto burner surface.
Glass Installation
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED
GLASS BEADS OR OTHER APPROVED FIRE MEDIA
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITH BURNER COVER IN
PLACE

9
CV-30-E Installation
• Place burner plate into Cove base.
• Remove the 4 ¼-20 stainless steel screws installed in
rivnuts.
• Make gas connections.
•Ignition wind guard should be oriented towards
cutout in burner plate. As shown in detailed view.
• Replace the 4 ¼-20 stainless steel screws back
through the burner and tighten into rivnuts.
BI-28
BP40RD-CV
Ignition Wind Guard

10
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and
important information related to the burner installation including: lighting and
operating instructions, safety information, and proper tightening of connections with
two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE® PLUS BURNER OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks