Outdoor GreatRoom Company CV-2424 User manual

The Cove Fire Pit
Installation Instructions for CV-2424

2

3
Contents
Required Tools………………………………….........3
Included With Your Fire Pit……………………….4
Assembly Instructions……………………………….5
Sparker Box Installation…………………………….5
Gas Connections……………………………………….6
Electrode Installation………………………………..7
Propane Tank Installation………………………….8
Install Fire Media……………………………………….9
Operating Instructions………………………………10
Required Tools
THREE people are required for this installation.
2 Open Ended Wrenches
To secure gas connections.
Leather Gloves
To protect hands from rough edges found on fire pit
during installation.
One AAA Battery (not included)
Required for electric spark igniter installation.
Utility Knife
To cut and remove packaging.
Power Drill
To remove support board from crate.
42482 REV-A 9-20-17
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed instructions
and important information related to hooking up your burner, including
safety information, proper tightening of connections with two wrenches and
full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CF-2424 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.

4
Included With Your Fire Pit
Cove 2424 Base with Key
Valve Control Panel Installed
(CV-2424-BASE)
(KV-CP-BLK)
Cove 2424 Door
(CV-2424-DOOR)
Black Key
(BF-KY-05)
24” x 24” Crystal Fire Burner
Kit with black trim
(CF-2424-BLK)
Refer to Crystal Fire Manual for items included with crystal fire burners.

5
Assembly Instructions
1. Remove Cove-2424-Base from Packaging crate
Remove side panels from crate using a power drill with
Philips head bit.
Three People are required to lift base out of packaging
and place into final location. CAUTION: Base is heavy,
take all necessary precautions to prevent injury during
installation.
2. Sparker Box Installation
Locate sparker inside of crystal fire burner box.
Remove sparker cap and hex nut. Insert AAA battery
(not included) with + end out.
Install sparker into control panel as shown below,
secure using hex nut and replace sparker cap.
Depress sparker button to ensure your sparker is
working properly. You should hear the spark behind the
sparker box.
Remove

6
3. Gas Connections
Ensure key valve is in the OFF position before
making any gas connections.
For propane tank installations, install included
propane hose and regulator to the control
panel as shown below. Use two wrenches to
ensure a gas tight connection.
For hard piped installations, connect the gas supply line
(not included) to the 3/8” male flare fitting on the key
valve. Use two wrenches to ensure a gas tight
connection.
Ensure the correct orifice is installed for the fuel type
you are using (see Crystal Fire Burner Owner’s Manual
included with burner for orifice sizing information).
Ensure flex line is securely tightened to the orifice. Use
two wrenches as shown.
TIGHTEN ALL CONNECTIONS SECURELY WITH TWO WRENCHES
TIGHTEN CONNECTION
SECURELY WITH WRENCH
Propane regulator
Or gas supply line

7
Attach flex line from the burner to gas valve as shown.
Use two wrenches to secure connection. Drop burner
into place in base.
4. Connect Ground wire and Electrode wire from
burner to sparker box.
Plug both BLACK wires hanging from the burner into
the back of the sparker box. If an orange wire is
present, do not use it. The orange wire is for Direct
Spark Ignition system only.
Test system by pushing the button on the
igniter. Consult the troubleshooting
section of the Crystal Fire Burner Owner’s
Manual, if the spark is weak, intermittent,
or not present.

8
5. Propane Tank Installation
With the propane tank valve and key valve off, attach
the propane regulator to the propane tank. Hand
tighten, do not use a wrench for this connection.
Lift and tilt the propane tank through the access door
into place underneath the base. Ensure that all hoses
and wires are kept away from the hot burner surfaces.
Use caution not to chip the edges of the concrete when
installing the tank.
Install the door by setting the bottom edge in place and
tilting into place. Secure by turning the ¼ turn cam lock
to lock the door in place.

9
6. Install Fire Media
Scatter all included glass beads, lava rock, or other
approved fire media evenly across entire burner
surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT
INCLUDED GLASS BEADS OR OTHER APPROVED FIRE
MEDIA
DO NOT OPERATE CRYSTAL FIRE BURNER WITH
BURNER COVER IN PLACE
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed instructions
and important information related to hooking up your burner, including
safety information, proper tightening of connections with two wrenches and
full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CF-2424 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.

10
7. Operating Instructions
Before operating your Cove 2424 fire pit, ensure all gas
connections are properly tightened and thoroughly leak checked.
Refer to the Crystal Fire Manual for information on proper leak
checking and other critical safety information.
With the Key Valve in the OFF position, open the valve
on the propane tank or natural gas supply.
Double check to make sure there are no gas leaks at the
regulator or inlet side of the key valve. If leak is
detected, immediately shut off the propane tank and
wait 5 minutes to allow gas to dissipate. Fix any leaks
before proceeding.
Press the sparker button and hold, look and listen for
spark between electrode and grounding rod.
While depressing the sparker, use the key to open the
key valve.
If burner does not light after 10 seconds, close the valve
and wait 5 minutes to allow gas to dissipate before
attempting ignition again.
Refer to the Crystal Fire Manual included with your burner for
more detailed information on operation, maintenance, and safety
of your burner.
3. Turn Key Valve to ON
2. Look/listen for spark
1. Depress sparker

11
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made with
pride in the USA.
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]