Outdoor GreatRoom Company CV-2424 User manual

The Cove Fire Pit
Installation Instructions for CV-2424

2

3
Contents
Required Tools………………………………….........3
Included With Your Fire Pit……………………….4
Assembly Instructions……………………………….5
CF-SPARKER Installation…………………………….5
Gas Connections……………………………………….6
Thermocouple Installation………………………..6
Electrode Installation………………………………..7
Propane Tank Installation………………………….8
Install Fire Media……………………………………….9
Operating Instructions………………………………10
Required Tools
THREE people are required for this installation.
2 Open Ended Wrenches
To secure gas connections.
Leather Gloves
To protect hands from rough edges found on fire pit
during installation.
One AAA Battery (not included)
Required for electric spark igniter installation.
Utility Knife
To cut and remove packaging.
Power Drill
To remove support board from crate.
42482 REV-C 11-12-20
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to hooking up your burner,
including safety information, proper tightening of connections with two
wrenches and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CFP2424 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.

4
Included With Your Fire Pit
Cove 2424 Base with Key
Valve Control Panel Installed
(CV-2424-BASE)
(KV-CP-BLK)
Cove 2424 Door
(CV-2424-DOOR)
Black Key
(BF-KY-05)
24” x 24” Crystal Fire Plus
Burner Kit with black trim
(CFP2424-BLK)
Refer to Crystal Fire® Plus Manual for items included with Crystal Fire®
Plus burners.

5
Assembly Instructions
1. Remove Cove-2424-Base from Packaging crate
Remove side panels from crate using a power drill with
Philips head bit.
Three People are required to lift base out of packaging
and place into final location. CAUTION: Base is heavy,
take all necessary precautions to prevent injury during
installation.
Remove
Locate CF-SPARKER inside of crystal fire burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery (not
included) with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.
1. CF-SPARKER Installation

6
See Crystal Fire® Plus instructions for burner installation.
oAll gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection with 2
wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as shown below.
Ensure sparker box is installed before this step.
3. Thermocouple Installation
•Refer to Crystal Fire® Plus instruction manual for detailed
attachment of thermocouple.
•Attach thermocouple to burner valve as shown below.
2. Gas Connections

7
Plug both BLACK wires hanging from the burner into the back of the CF-
SPARKER. If an orange wire is present, do not use it. The orange wire is for
Direct Spark Ignition system only.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire® Plus Burner Owner’s Manual, if
the spark is weak, intermittent, or not present.
4. Electrode Installation

8
5. Propane Tank Installation
With the propane tank valve and key valve off, attach
the propane regulator to the propane tank. Hand
tighten, do not use a wrench for this connection.
Lift and tilt the propane tank through the access door
into place underneath the base. Ensure that all hoses
and wires are kept away from the hot burner surfaces.
Use caution not to chip the edges of the concrete when
installing the tank.
Install the door by setting the bottom edge in place and
tilting into place. Secure by turning the ¼ turn cam lock
to lock the door in place.

9
6. Install Fire Media
a. Scatter all included glass beads, lava rock,
or other approved fire media evenly
across entire burner surface.
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER
WITHOUT INCLUDED GLASS BEADS OR OTHER
APPROVED FIRE MEDIA
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER
WITH BURNER COVER IN PLACE
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to hooking up your burner,
including safety information, proper tightening of connections with two
wrenches and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CFP2424 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.

10
7. Operating Instructions
Before operating your Cove 2424 fire pit, ensure all gas
connections are properly tightened and thoroughly leak checked.
Refer to the Crystal Fire® Plus Manual for information on proper
leak checking and other critical safety information.
Refer to the Crystal Fire® Plus Manual included with your burner
for more detailed information on operation, maintenance, and
safety of your burner.
Verify control valve is in OFF position. If operating on a self-contained propane
cylinder, ensure cylinder valve is CLOSED. If operating on a hard-piped system, ensure
main gas supply shut-off valve and all other valves in gas system are OPEN.
If operating on a self-contained propane cylinder, slowly open cylinder valve.
Press and hold sparker button. Verify an audible and visible spark is present within
the ignition wind guard.
Gently press and turn control knob to LOW/IGNITION position. Fully depress control
knob and hold for 3-5 seconds. Burner should ignite and continue to operate when
control knob is released.
If burner does not light or remain lit after 20 seconds of attempting ignition, turn
control valve to OFF position and wait 5 minutes to allow gas to dissipate before
attempting ignition again. DO NOT ATTEMPT TO LIGHT BURNER IF YOU SMELL GAS.
With burner lit and operating, the flame height can be adjusted between LOW and
HIGH at any time.
While depressing the sparker, use the key to open the key valve.
3. Turn valve to ON
2. Look/listen for spark
1. Depress sparker

11

12
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made with
pride in the USA.
Warranty: Fire pit tables are covered under a 1- year
manufacturer’s warranty. Please visit
https://www.outdoorrooms.com/product-registration
to register your product.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]