Outdoor GreatRoom Company Kenwood KW-1224-19-K User manual

1
Kenwood Fire Pit Table
Installation Instructions for Kenwood Fire Pit Table
KW-1224-K

2
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Phillips Screwdriver
To attach mounting screws to control panel
Two people are required for this
installation
Contents
Required Tools………………………………….........2
Included with your Fire Pit………………………..3
Assembly Instructions……………………………….4
Gas Connections……………………………………….7
Igniter Installation…………………………………….9
Glass Installation………………………………………10
Position Your Tank…………………………………..11
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
REV B 8-20-18

3
Included with your Fire Pit
Panel C [X1]
M6 Allen
Wrench [X1]
Bolt Caps
[X4]
TOUCH
UP
PAINT
M6X20
Panel B [X1]
Access Door [X1]
Top
Center Support [X2]
Bolt A [X16]
Gas Valve Kit
Gas Valve [X1]
Mounting
screws [X2]
Control knob
[X1]
CF-1224 Burner
Panel A [X1]
Touch-Up
Paint Bottle
[X1]

4
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
55
1. Unpack contents from box, and remove individual packaging from each
piece.
2. Lay Side Panel with Control Panel on soft, flat surface.
3. Position Support Piece on the Side Panel. NOTE: It is very important to
positon the Support Piece as shown in the picture below, to ensure that
your burner and propane tank fit correctly with your fire pit table base.
Assembly Instructions
INSTALL NOTE: Final tightening of bolts should be completed following
installation of all panels.
1. Unpack all the contents from the box and remove the individual
packaging from each component. Remove 4 pre-installed bolts (Bolt A)
from the underside of the Top.
2. Carefully lay the Top, with underside facing upwards, on a soft and flat
surface. Attach Panel A using Bolt A (x2) as shown below.
3. Attach Panel B on the opposite side of Panel A using Bolt A (x2)
as shown below.

5
5. Attach a Center Support piece,
as shown below, to the bottom
of the fire pit using Bolt A (x4).
NOTE: Drainage holes on
Center Support piece must be
facing down towards the
surface on which you will be
placing your fire pit.
4. Attach Panel C using Bolt A (x4) as shown below.
6. Attach a second Center Support
piece to the top of the fire pit, on the
opposite side from Panel C, using Bolt A
(x4).
.
.
.
.
NOTE: Drainage holes on
Panel C must be facing
down towards the surface
on which you will be
placing your fire pit.
Drainage holes
.
.
.
.
A

6
Insert screws
included with
Gas Valve Kit
8. Hold the Gas Valve in place from behind the control panel as shown while
inserting the two included Mounting Screws. Use a Phillips screwdriver to
fasten. Attach control knob by pressing on to the valve stem.
7. Do a final tightening of the bolts you have installed in your fire pit.
Then, with the help of another person, turn the table right side up.
Bottom
Top

7
1. Reach inside the burner cut-out and attach natural gas supply
line using a 3/8” flare fitting, or attach the included black
rubber propane hose and regulator to the bottom fitting of the
control valve.
TIGHTEN SECURELY WITH A WRENCH
2. Lay the burner upside down on a flat, soft surface to avoid
scratching the polished metal. Ensure the correct orifice is
installed for the fuel type you are using (see Crystal Fire user
manual included with burner for orifice sizing information).
Attach the included metal flex hose to the burner.
TIGHTEN SECURELY WITH TWO WRENCHES
Gas Connections
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Propane
input
Natural
gas input
or
Natural gas supply line
as specified by local
building codes

8
3. Set Burner into the fire pit base as shown below.
Metal flex line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH
4. Attach flex line from the burner to gas valve as
shown below.
Electrode
Access Door

9
Igniter Installation
Sparker will not operate correctly without an ignition and ground wire
attached.
Plug both BLACK wires hanging from the burner into the back of
the sparker box.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire Owner’s Manual, if
the spark is weak, intermittent, or not present.
1. Make sure the valve is in the OFF
position before beginning.
2. Install sparker as shown, using a
AAA battery (not included).
Negative end should be placed
inside the CF-SPARKER, positive
end outside of the CF-SPARKER.
OFF

10
Glass Installation
1. Scatter all of the included Glass Beads evenly onto burner
surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT GLASS
BEADS OR OTHER DECORATIVE MEDIA PRESENT
DO NOT OPERATE CRYSTAL FIRE BURNER WITH GLASS COVER IN
PLACE (NOT INCLUDED)

11
After installing igniter and making gas connections, verify that
all connections are tight and that no leaks are present using a
solution of soapy water or a commercially available leak-check
solution.
Position Your Tank
(if applicable)
1. Connect the propane hose/regulator to the propane tank and
hand tighten (DO NOT USE A WRENCH) and slide the propane
tank past the dotted line to ensure the Access Door closes
properly. Attach the Access Door.
2. With the tank inside, ensure that no hoses, wires, or any other
components are kinked or touching the burner pan.

12
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form/
to register your product.
Care and maintenance note:
Light scratches may be removed from the poly-wood surfaces
of this fire pit by gently sanding with 220-grit sandpaper in the
same direction as the grain. Sanding too deeply or not
following the grain of the material could result in permanent
damage.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]