Outdoor GreatRoom Company Colonial User manual

1 | P a g e
Colonial and Grand Colonial Fire Pit Tables
Installation Instructions

2 | P a g e
Contents
Contents………………………………………………………………………………..2
Required Tools……………………………………………………………..……..2
Assembling the Grand Colonial…………………………….………4
Assembling the Colonial…………………………………..………………6
Gas Connections…………….…………………………………………..……...7
Installing Igniter……………………………………………………………………8
Placing propane tank and finishing touches……………..12
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found on the
coffee table.
One (1) AAA Battery (not included)
Required for piezoelectric igniter installation.
Electric screw gun
90220:C 5.24.2012

3 | P a g e
Included with Grand Colonial:
Included with Colonial:
Tabletop frame Base Granite Pieces (x4)
Top-Securing Bracket (x4)
Screws (x4)
Lazy Susan/Burner Cover
Depending on which model you purchased, turn to the
corresponding page in this manual for installation
instructions.
Base Supercast Tabletop with center burner
cover
(Instructions begin
on next page)
(Flip to page 6 for
assembly instructions)
Risers (4) Screws (4)
Grounding wire(x1)*
Grounding wire(x1)*
* Grounding wire may not be used depending on igniter
included with your burner. See P.8 for more information

4 | P a g e
Assembling the Grand Colonial
1. Remove all components from packaging and
inspect for damage or missing parts.
2. Move the base to desired location and set into
place before installing granite.
- When locating your coffee table, refer to the
Crystal Fire manual and maintain clearance to
combustibles.
3. Place top on base
as shown.
4. Line top up with base as shown.
Holes in tabletop frame are also used
for an alternate installation so not
every hole will line up directly
centered in each corner
of the base. This is
normal, as only 4 of
these holes are used in
this installation. A solid
line in the diagram at
right indicates the
approximate location
of the holes used for
mounting. Dashed lines
are unused holes.
Dashed lines: Holes not used
for this installation

5 | P a g e
6. With top securely
fastened to base, set granite
sections into place, polished
side up.
4. With top centered on
base and one hole
approximately centered on
each corner of the base,
insert a mounting clip into
mounting hole
(refer to image at right.)
5. Insert one of the
included screws through the
hole in the mounting clip
and screw into the table
base. Do not over-tighten as
this may cause stripping.
If stripping occurs, rotate
the top approximately 1”
and re-insert all screws.
Unused screw
hole
For gas hookup instructions, turn to page 7

6 | P a g e
Colonial Table Setup
1. Remove all components from packaging and
inspect for damage or missing parts.
2. Place the fiberglass table base in your desired
location on flat, level ground.
3. Viewing the base from above, place a riser piece
on each corner of the base as shown below.
3a.Insert a screw into each
riser to attach to the table
base.
DO NOT OVERTIGHTEN
This may cause stripping. If
stripping occurs, remove
screw and move the riser at
least ½” in any direction
before putting the screw back
in.
4. With help from another person, gently set concrete
top onto the base and center it. If the top doesn’t sit
flat, rotate it until it sits evenly. For a more permanent
installation, an outdoor-rated construction adhesive or
silicone can be used to attach the top to the base.
5. Gently lower your crystal fire burner into the burner
cutout and continue to the next page for gas hookup
and igniter hookup instructions.

7 | P a g e
Gas Connection
1. With proper orifice installed for the
application (#43 for propane, #31 for
natural gas) and metal flex hose attached,
set burner in base.
2. Connect the incoming gas hose (black
rubber hose from propane tank or incoming
natural gas line) to the valve and tighten
securely with two wrenches. Repeat with
flexible metal gas line from the valve to the
underside of burner. It is not recommended
to use Teflon tape or pipe dope on the
connection to the valve with flare fittings.
LPG installations use the hose and regulator
provided with the burner.
For Natural Gas hookup information and
any other info not listed here consult your
Crystal Fire owner’s manual.
Read and understand your Crystal Fire burner owner’s manual
before beginning burner hookups or using the device.
Metal flex hose to burner
Incoming LP or NG gas

8 | P a g e
Igniter Installation
Style 1: Single Prong Igniter
Your Crystal Fire ™burner includes one of two styles of igniter. These
can be distinguished by the number of wire connection prongs on the
back (glossy) side. If one prong is present see below, otherwise turn to
page 10 for instructions on how to install and use a two-pronged igniter.
Step 2: Disassemble igniter by
unscrewing button cap, followed by
plastic nut
Step 3: place looped end of
grounding wire onto your igniter. As
shown
Step 1: Make sure the valve is in
the OFF position

9 | P a g e
Step 4: Slide the igniter with
attached grounding wire through the
hole in the fiberglass base from the
inside and tighten the plastic nut onto
the shaft until snug but not
overtightened.
Before screwing button cap on, insert
one AAA battery into igniter, + side
facing out.
Step 4: There are two small
hexagonal nuts on the bottom of your
Crystal Fire (locations shown at right).
Loosen one of these nuts and slide the
free (forked) end of the grounding
wire onto it and re-tighten the nut.
Your igniter is now grounded.
Test system by depressing the button on the igniter. A
continuous repeating spark between the igniter
electrode and spark-receiving probe means everything
is connected properly. Consult the troubleshooting
section of your crystal fire owner’s manual if spark is
weak, intermittent, or not present.

10 | P a g e
Style 2: Double Prong Igniter
1. Make sure the valve is in the OFF
position
2. Unscrew sparker cap and hex nut (sparker
included with burner). Install as shown below.
Wall of base
If your Crystal Fire burner included a double-pronged igniter, there will
be a grounding wire attached to the bottom of your burner bowl and
the included grounding wire with your Colonial will not be used.