Outdoor GreatRoom Company Linear Fire Pit Table User manual

1 | P a g e
Linear Fire Pit Table
Installation Instructions for:
•Havenwood models
•Key Largo models
•Providence models

2 | P a g e
Contents
Required tools…………………………………………………………………………………2
Placing and Assembling the Fire Table……..………………………………………3
Sparker Installation…………………………………….……………….…….………..….5
Gas Connections…………….………………………………………….…………………...5
Thermocouple Installation…………………………………………………….………..6
Electrode Installation…………………………............................................…6
Locating Propane tank………..………………………………………………………..…7
Finishing Touches……………………………….……………………………………………8
Service Parts………………………………………………………………………………….10
Required Tools
•2 Open Ended Wrenches - To make gas connections.
•Leather Gloves - To protect hands from rough edges found
on the table.
•One (1) AAA Battery (not included) - Required for
piezoelectric igniter installation.
•Electric Screw Gun with Philips tip - (Used for attaching
brackets to top and top to frame.)
•Do not attempt to perform installation by yourself. This fire
table has a heavy top. Have at least one other person help
you.
05.22.2023

3 | P a g e
Placing and Assembling the Fire Table
1. Remove all components from packaging.
2. Move the base section to desired location.
3. When locating your table, refer to the Crystal Fire® Plus
manual and maintain clearance to combustibles.
4. Adjust leveling legs on bottom to ensure tank door
operates smoothly.
5. If applicable, install LED kit, or skip to step 6.
6. Set top into place.
a. Supercast tops & Stainless-Steel tops skip to
step 8
7. Everblend top only: install mounting bracket.
a. Set brackets into place, attach using supplied
screws (4)

4 | P a g e
8. Carefully set Burner into place. See the sections labeled
Gas Connection and Ignitor Installation to install gas lines
and piezo electric igniter.

5 | P a g e
CF-SPARKER Installation
•Remove CF-SPARKER cap and hex nut. Insert AAA battery (not
included) with + end out.
•Install CF-SPARKER into control panel as shown below.
•Depress CF-SPARKER button to test your sparker.
Gas Connections
See Crystal Fire Plus® instructions for burner installation.
Read and understand your Crystal Fire® Plus owner’s manual
before beginning burner hookups or using the device.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.
Attach burner
valve to control
panel with
provided screws as
shown below.
Ensure sparker box
is installed before
this step.

6 | P a g e
Thermocouple Installation
•Refer to Crystal Fire® Plus instruction manual for detailed
attachment of thermocouple.
•Attach thermocouple to burner valve as shown below.
Electrode Installation
•Connect igniter and ground wire to sparker box. Both wires can
connect to either connection point. The unit will operate in
either configuration.
•Test system by pushing the button on the ignitor. Consult the
troubleshooting section of the Crystal Fire® Plus Burner Owner’s
Manual, if the spark is weak, intermittent, or not present.

7 | P a g e
NOTE: Over time the bearings
in the door glides may require
re-greasing. Any spray
lubricant, such as WD-40, may
be used to lubricate drawer
glides. Perform annually or on
an as needed basis to maintain
smooth operation.
Locating your Tank
(If applicable)
1. Tilt your propane tank into the slide out tank drawer.
2. With the propane tank and control
valve in the OFF position, connect
the Regulator Hose, included with
the Crystal Fire® Plus burner, to
your propane tank. Hand tighten
connection, do not use tools to
tighten this connection.
3. Slide tank drawer in. Ensure that the Gas hose does not get
pinched in the process of sliding the tank drawer.

8 | P a g e
Gas Line Location
•If the fire pit is to be supplied by natural gas or hard
piped propane system, locate your plumbing outside
the area of the tank drawer. Gas can be stubbed up
within the shaded area indicated below.
30-5/8 x 12-7/8

9 | P a g e
Finishing touches
•Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming an
even layer of beads.
•Cover ignitor with decorative glass beads.
WARNING
After consulting the manual and following instructions, remember;
before operating, all gas connections must be fully checked for leaks.
DO NOT BURN WITHOUT GLASS OR OTHER APPROVED
DECORATIVE FIRE MEDIA
DO NOT BURN WITH GLASS BURNER COVER INSTALLED

10 | P a g e
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for
detailed instructions and important information related to
hooking up your linear burner, including safety information,
proper tightening of connections with two wrenches and full
burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CFP1224 BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE® PLUS MANUAL. IF YOU
ARE UNSURE OF HOW TO COMPLETE THE STEPS OUTLINED,
CONSULT A QUALIFIED TECHNICIAN

11 | P a g e
Service Parts
•Refer to Crystal Fire® Plus instruction manual for
burner service parts.
Part
24”
42”
Base
Black
Graphite
White
Key Largo stucco
Providence
HWB-1224-BASE
HWG-1224-BASE
HWW-1224-BASE
3007-013
HWB-1242-BASE
HWG-1242-BASE
HWW-1242-BASE
3007-012
Drawer Assembly
Black
Graphite
White
Key Largo Stucco
Providence
3007-015-Black
3007-015-Graphite
3007-015-White
3007-015-Stucco
3007-130-Black
Tops
Pebble
Carbon
Driftwood
Supercast
Stainless Steel
HVP-3044-TOP
HVG-3044-TOP
HVD-3044-TOP
PROV-SS-TOP
HVP-3062-TOP
HVG-3062-TOP
HVD-3062-TOP
2554-1254-MM
KEY-LARGO-SS-TOP
Glass Burner Cover
1224-GREY-GLASS-COVER
1242-GREY-GLASS-COVER
Touch up
Pebble top
Carbon top
Driftwood top
EB-TU-PB
EB-TU-CG
EB-TU-DW

12 | P a g e
9583 217th St. W. •Lakeville, MN 55044
Toll Free: 1-866-303-4028 •[e-mail]
Thank you for purchasing an Outdoor
GreatRoom Company product! This fire
pit was made with pride in the USA
with US & imported parts.
Warranty: Fire pit tables are covered under a 1-year
manufacturer’s warranty. Please visit
https://www.outdoorrooms.com/product-registration
to register your product.