Outdoor GreatRoom Company UPT-1242 User manual

1 | P a g e
Uptown Fire Pit Table
Installation Instructions for UPT-1242 and UPT-1242-BRN

2 | P a g e
Contents
Contents……………………………………………………..2
Required Tools…………………………………………...3
Placing and assembling the Table.……..…4
CF-SPARKER Installation………………….….…….6
Gas Connections…………….………………...……...6
Thermocouple Installation……………………….8
Electrode Installation………………………………..8
Locating Propane tank…………………………….9
Locating Natural Gas Line…………………….10
Fire Media Installation…………………………..…11
90223:F 12.05.19

3 | P a g e
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found
on the coffee table.
One (1) AAA Battery(not
included)
Required for piezoelectric igniter
installation.
Do not attempt to perform
installation by yourself. This fire
pit table is constructed of steel
and heavy stone products.
Have at least one other
person help you.

4 | P a g e
Placing and Assembling the Fire Pit table
1. Remove all components from packaging.
2. Move the base sections without door to desired
location and set into place spaced
approximately 21” from each other.
3. When locating your coffee table, refer to the
Crystal Fire Plus manual and maintain clearance
to combustibles.
4. Assemble as shown below.
Igniter on side
closest to tank base

5 | P a g e
5. Insert supplied sheet metal screws into the
locations shown by arrows below. This secures
the granite tile top to the base.
Read and understand your Crystal Fire Plus owner’s manual
before beginning burner hookups or using the device.
Align smaller base with concrete top as shown by
dashed line.

6 | P a g e
CF-SPARKER Installation
Gas Connections
Locate CF-SPARKER inside of crystal fire burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included)
with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.
Using 2 wrenches, disconnect VCSV valve from flex line.

7 | P a g e
See Crystal Fire Plus instructions for burner installation.
All gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection with
2 wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as shown
below. Ensure sparker box is installed before this step.
Feed flex line through hole opening on side of top
Using 2 wrenches, reconnect VCSV valve to flex line.
Perform leak test on connection.

8 | P a g e
Thermocouple Installation
Electrode Installation
•Refer to Crystal Fire Plus instruction manual for detailed
attachment of thermocouple.
•Attach thermocouple to burner valve as shown below.
•Plug both BLACK wires hanging from the burner into the back of the
CF-SPARKER. If an orange wire is present, do not use it. The orange
wire is for Direct Spark Ignition system only.
•Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire Plus Burner Owner’s
Manual, if the spark is weak, intermittent, or not present.

9 | P a g e
NOTE: Over time the bearings
in the door glides may require
re-greasing. Any spray
lubricant, such as WD-40, may
be used to lubricate drawer
glides. Perform annually or on
an as needed basis to maintain
smooth operation.
Locating your Tank
(If Applicable)
1. Tilt your propane tank into the slide out tank drawer.
2. With the propane tank and control
valve in the OFF position, connect
the Regulator Hose, included with
the Crystal Fire Plus burner, to
your propane tank (not included).
Hand tighten connection, do not
use tools to tighten this
connection.
3. Slide tank drawer in. Ensure that the Gas hose
does not get pinched in the process of sliding the
tank drawer.

10 | P a g e
Locating Natural Gas Line
(If Applicable)
Top View of Base with Door
Locate natural gas stub inside of the red outline to
avoid clearance issues with the door for natural gas
installations.

11 | P a g e
Fire Media Installation
Scatter all included glass beads, lava rock, or
other approved fire media evenly across entire
burner surface.
IMPORTANT
Please consult your Crystal Fire Plus instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CFP1242 BURNER WITHOUT FIRST
CONSULTING THE MANUAL. IF YOU ARE UNSURE OF HOW TO
COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks
DO NOT BURN WITHOUT GLASS OR OTHER
APPROVED DECORATIVE FIRE MEDIA
DO NOT BURN WITH GLASS COVER INSTALLED

12 | P a g e
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]
Warranty: Fire pit tables are covered under a 1-year
manufacturer’s warranty. Please visit
https://www.outdoorrooms.com/product-registration
to register your product.
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made
with pride in the USA.