Outdoor GreatRoom Company WP-1616 User manual

The Westport Fire Pit Table
Installation Instructions for WP-1616 and WP-INT

2
IMPORTANT
Please consult your Crystal Fire Manual or INT-EZ manual for detailed instructions and
important information related to the burner installation including: lighting and operating
instructions, safety information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER OR INTRIGUE WITHOUT FIRST
CONSULTING T
HE PROPER MANUAL

3
Contents
Required Tools……………………………………………….2
Included with your Fire Pit……………………………..3
Fire Pit Assembly Instructions…………………………4
Burner Installation WP-1616.………………………5-7
Position Your Propane Tank……………………………8
Glass Installation…………………………………………….9
Burner Installation WP-INT……………………..10-11
Warranty Information…………………………………..12
Required Tools
 Utility Knife
To cut and remove packaging
 Two Open Ended Wrenches
To secure gas connections
 Leather Gloves
To protect hands from glass and sharp edges during installation
 One AAA Battery (WP-1616) or 2 D-Cell
Batteries (WP-INT)
Required for Electric Spark igniter installation
 Power Drill with Philips head bit
To attach mounting brackets to secure tile top to base.
 Philips screw driver
To attach control panel for WP-INT
 At least Two people are required for this
installation
42471 REV A
2
-
23
-
2017

4
Included With Your Fire Pit
CF-1616-PTR Burner OR INT-EZ and Trim
WP-BASE
WP-TILETOP
Top Attachment Bracket (2)
Self-tapping Philips Head Screws (8)
(WP-INT ONLY)
6 lbs. Tumbled Lava Rock (LAV-TMB)
13
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made with
pride in the USA.
14400 Southcross Drive West • Suite 100 • Burnsville, MN 55306
Toll Free: 1-866-303-4028 • [e-mail]

12
4. Make wire connections from burner to control panel:
a. Use spade connectors provided to connect
the wires from the intrigue (Brown) to the
wires from the control panel (Black).
5. Drop INT-EZ and trim into fire pit. Orient the INT-EZ
Base so that the access door is easily accessible.
6. Carefully install tumbled lava rock; be
careful not to damage the glass cylinder
when installing lava rock.
Warranty: Fire pit tables are covered
under a 1- year manufacturer’s
warranty. Please visit
Wires form
INT-EZ
Wires from
control panel
Intrigue Access door
Westport Access door
5
Fire Pit Assembly Instructions
1. Carefully remove product from packaging. Make sure
that all parts are included and undamaged. Ensure you
have the proper tools for assembly.
2. Place WP-BASE into the final location where you want
your fire pit.
3. Place WP-TILETOP onto WP-BASE. Position the top so
that the base is centered in the opening.
4. Using a power drill and Self Tapping Philips Head
Screws provided, attach Top Attachment Brackets to
secure WP-TILETOP to WP-BASE as shown in the figure
below. Secure each attachment bracket using 4 screws.
Mounting Bracket Locations

6
Burner Installation (WP-1616)
1. Attach Natural Gas supply line or included black rubber
propane hose/regulator (depending on gas type) to
control valve.
TIGHTEN CONNECTIONS SECURELY WITH TWO WRENCHES
Ensure all connections are secure and leak free before using fire pit.
2. Lay the burner upside down on a flat, soft surface to
avoid scratching the metal trim. Ensure the correct
orifice is installed for the fuel type you are using (see
Crystal Fire user manual included with burner for
orifice sizing information). Attach the included metal
flex hose to the burner.
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe sealant on flare fittings.
Propane or
Natural Gas
input
or
Natural gas supply line
as specified by local
building codes
11
Burner Installation (WP-INT)
1. Remove existing control panel from base:
a. Use a Philips head screw driver to remove the
4 screws.
2. Replace existing control panel with intrigue control
panel:
a. Use a Philips head screw driver to replace the
four screws in the four corners of the control
panel.
3. Assemble INT-EZ with burner trim. Refer to INT-EZ
manual before attempting to install.
Read and understand your
INT
-
EZ
owner’s manual
before
beginning burner installation or using the device.
IMPORTANT
Please consult your INT-EZ instruction manual for detailed instructions
and important information related to burner installation, including:
lighting and operating instructions, and safety information.
DO NOT ATTEMPT TO INSTALL INT-EZ BURNER WITHOUT FIRST
CONSULTING THE INT-EZ OWNER’S MANUAL.

10
Glass Installation
 Scatter all the included glass beads evenly onto burner
surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT
INCLUDED GLASS MEDIA OR OTHER APPROVED FIRE MEDIA
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to burner installation,
including: lighting and operating instructions, safety information, and
proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CF-1616 CRYSTAL FIRE BURNER
WITHOUT FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember: before
operating, all gas connections must be fully checked for leaks
7
TIGHTEN CONNECTIONS SECURELY WITH TWO WRENCHES
Ensure all connections are secure and leak free before using fire pit.
3. Remove access door to fire pit and orient the burner in
the Fire Pit as shown below.
4. Attach Flex Line from burner to control valve as shown
below.
Sparker Electrode
Control Panel
Side
Door Side
Metal flex line
to burner
ONLY
TIGHTEN CONNECTION SECURELY
WITH WRENCH

8
5. Install Sparker box into control panel as shown
below. Insert AAA Battery with Positive (+) end
facing out. To ensure sparker box is working
correctly, press button and listen for sparking
behind the sparker box.
6. Connect sparker wire and ground wire from
burner to sparker box as shown below. Ensure
good contact between connections. Test sparking
system by pressing the button and
listening/watching for the spark between the
electrode and sparking tab at the burner surface.
Consult the troubleshooting section of the Crystal
Fire Manual if spark is weak, intermittent, or not
present.
After installing igniter and making gas connections, verify that gas
connections are tight and that no leaks are present using a solution of
soapy water or a commercially available leak-check solution.
9
Position Your Tank
(If Applicable)
 Open the access door and connect the propane
hose/regulator to the propane tank and hand tighten
(DO NOT USE A WRENCH).
 Insert the propane tank by tipping at a 45 degree angle
as shown in the picture in order to fit tank into access
door opening.
 Tip tank upright into final position once inside the fire
pit.
 Ensure the tank is seated properly and stays vertical
during operation and while not in use.
 Ensure that no hoses, wires or anything else is kinked
or touching the bottom of the burner