Outdoor GreatRoom Company Montego User manual

1
Montego Fire Pit Table
Installation Instructions for Montego Fire Pit Models
MG-1242-BLSM-K and MG-1242-BLK-K

2
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Two people are required for this
installation
Contents
Required Tools………………………………….........2
Included with your Fire Pit………………………..3
Assembly Instructions……………………………….4
Gas Connections……………………………………….7
Igniter Installation…………………………………….9
Glass Installation………………………………………10
Position Your Tank…………………………………..11
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CF-1242 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42449 REV E 11.23.20
Contents
Required Tools…………………………………................2
Included with your Fire Pit……………………….……..3
Assembly Instructions…………………………….…..….4
CF-SPARKER Installation …………………………..…...6
Gas Connections…………………………………………….7
Thermocouple Installation……………………………..8
Electrode Installation………………………………….....8
Glass Installation…………………….………………………9
Position Your Tank…………………………..…………….10
Riser Kit Installation…………………………………..…11

3
Included with your Fire Pit
Panel C [X 1]
M6 Allen
Wrench [X 1]
Bolt Caps
[X 4]
TOUCH
UP
PAINT
Touch-up
Paint [X 1]
M6X35
M6X20
M6X16
Clear Silicone Pads
[X 6]
Center Support
[X 1]
Bottom
Top
Panel A [X 1]
Panel B [X 1]
Access Door [X 1]
Glass Top
Glass Cover
Bolt A [X 4]
Bolt B [X 4]
Bolt C [X 4]
Gas Valve Kit
Gas Valve (x1)
Mounting
screws (x2)
Control knob
(x1)

4
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
55
1. Unpack contents from box, and remove individual packaging from each
piece.
2. Lay Side Panel with Control Panel on soft, flat surface.
3. Position Support Piece on the Side Panel. NOTE: It is very important to
positon the Support Piece as shown in the picture below, to ensure that
your burner and propane tank fit correctly with your fire pit table base.
Assembly Instructions
1. Unpack the fire pit table contents from the box, and remove individual
packaging from each piece.
2. Lay Panel A on soft, flat surface.
3. Position Center Support on Panel A.
NOTE: it is very important to place the Center Support exactly as shown in
the picture below. This will ensure that your burner (and propane tank, if
applicable) will fit correctly with your fire pit table base. (Refer to “Included
with Your Fire Pit” for component details).
NOTE: curve facing
inward toward
Control Panel.
4. Attach Center Support with Bolt A (x2).
A
A
Panel A

5
4. Stand up Panel A and use 2 more Bolt
Ato attach Center Support to Panel B.
5. Use Bolt B (x4) to attach
Panel C as shown.
6. Remove the 4 pre-installed bolts (Bolt C) from the underside of the
Glass Top , set the top into place on the base, and reinstall the bolts to
fasten the top to the base.
7. Once the Glass Top is in place, attach the Access Door to the fire pit table
base. Set mounting pins at bottom of Access Door into the mounting holes
located on side panels as shown below.
Optional: Attach Bolt
Caps to Bolt C if you
desire. Simply press on.
A
A
Panel C
B
C

6
CF-SPARKER Installation
Locate CF-SPARKER inside of Crystal Fire® Plus burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery
(not included) with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.

7
Gas Connections
Read and understand your Crystal Fire® Plus owner’s manual
before beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Insert screws
included with
Gas Valve Kit
See Crystal Fire® Plus instructions for burner installation.
All gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection with
2 wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as shown
below. Ensure sparker box is installed before this step.

8
Igniter
Igniter
Thermocouple Installation
•Refer to Crystal Fire® Plus instruction manual for detailed attachment
of thermocouple.
•Attach thermocouple to burner valve as shown below.
Electrode Installation
Plug both BLACK wires hanging from the burner into the back of the
CF-SPARKER. If an orange wire is present, do not use it. The orange
wire is for Direct Spark Ignition system only.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire® Plus Burner Owner’s
Manual, if the spark is weak, intermittent, or not present.

9
Glass Installation
2. Place a single Silicone Pad in each corner and two in the center as
shown below.
3. Set the cover into place on top of the burner with silicone pads
facing down.
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITH GLASS COVER
IN PLACE
1. Scatter all of the included Glass Beads evenly onto burner
surface.
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT
GLASS BEADS OR OTHER DECORATIVE MEDIA PRESENT

10
After installing igniter and making gas connections, verify that
all connections are tight and that no leaks are present using a
solution of soapy water or a commercially available leak-check
solution.
Position Your Tank
(if applicable)
1. Remove door, connect the propane hose/regulator to the
propane tank and hand tighten (DO NOT USE A WRENCH) and
slide the propane tank past the dotted line to ensure the door
closes properly.
2. With the tank inside, ensure that no hoses, wires, or any other
components are kinked or touching the burner pan.