Outdoor GreatRoom Company UPT-1242 User manual

1 | P a g e
Uptown Fire Pit Table
Installation Instructions for UPT-1242 and UPT-1242-BRN

2 | P a g e
Contents
Contents……………………………………………………..2
Required Tools…………………………………………...3
Placing and assembling the Table.……..…4
CF-SPARKER Installation………………….….…….6
Gas Connections…………….………………...……...6
Thermocouple Installation……………………….8
Electrode Installation………………………………..8
Locating Propane tank…………………………….9
Locating Natural Gas Line…………………….10
Fire Media Installation…………………………..…11
Required Tools
Utility Knife - To cut and remove packaging
2 Open Ended Wrenches - To make gas connections
Phillips Screwdriver –To attach support base to top
Leather Gloves - To protect hands from rough edges
found on the coffee table.
One (1) AAA Battery (not included) - Required for
piezoelectric igniter installation.
Do not attempt to perform installation by yourself. This
fire pit table is constructed of steel and heavy stone
products. Have at least one other person help you.
90223:H 12.10.21

3 | P a g e
Placing and Assembling the Fire Pit table
1. Remove all components from packaging.
2. Move the base sections to desired location and
set into place spaced approximately 26.50”
from each other.
3. When locating your coffee table, refer to the
Crystal Fire® Plus manual and maintain
clearance to combustibles.
4. Assemble in order as shown below.
Igniter on side
closest to tank base
26.50”

4 | P a g e
5. Insert supplied sheet metal screws into the
locations shown by arrows below. This secures
the tile top to the base.
6. Align holes on support base with riv-nuts in the bottom
of tile top. Using a Philips screwdriver and supplied bolts,
attach the support base to the top as shown in the image
below. Top may be needed to be lifted up to help position
support base.

5 | P a g e
Read and understand your Crystal Fire® Plus owner’s manual
before beginning burner hookups or using the device.
7. Align concrete top as shown by dashed line.
If the table is relocated, disconnect support base from tile
top before moving. Failure to do so may result in riv-nuts
becoming detached from tile top.

6 | P a g e
CF-SPARKER Installation
Gas Connections
Locate CF-SPARKER inside of crystal fire burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included)
with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Locate and orient
sparker box on
control panel as
shown. Sparker box
must be installed
before burner valve.
Using 2 wrenches, disconnect VCSV valve from flex line.

7 | P a g e
See Crystal Fire Plus instructions for burner installation.
All gas connections were completed at the factory.
Check all connections for leaks. If needed, tighten connection with
2 wrenches and re-check for leaks.
Attach burner valve to control panel with provided screws as shown
below. Ensure sparker box is installed before this step.
Using 2 wrenches, reconnect VCSV valve to flex line.
Perform leak test on connection.

8 | P a g e
Thermocouple Installation I
Electrode Installation
•Refer to Crystal Fire® Plus instruction manual for detailed
attachment of thermocouple.
•Attach thermocouple to burner valve as shown below.
•Connect igniter and ground wire to sparker box. Both wires can
connect to either connection point. The unit will operate in either
configuration.
•Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire® Plus Burner Owner’s
Manual, if the spark is weak, intermittent, or not present.

9 | P a g e
NOTE: Over time the bearings
in the door glides may require
re-greasing. Any spray
lubricant, such as WD-40, may
be used to lubricate drawer
glides. Perform annually or on
an as needed basis to maintain
smooth operation.
Locating your Tank
(If Applicable)
1. Tilt your propane tank into the slide out tank drawer.
2. With the propane tank and control
valve in the OFF position, connect
the Regulator Hose, included with
the Crystal Fire® Plus burner, to
your propane tank (not included).
Hand tighten connection, do not
use tools to tighten this
connection.
3. Slide tank drawer in. Ensure that the Gas hose
does not get pinched in the process of sliding the
tank drawer.

10 | P a g e
Locating Natural Gas Line
(If Applicable)
Top View of Base with Door
Locate natural gas stub inside of the red outline to
avoid clearance issues with the door for natural gas
installations.