Outdoor GreatRoom Company BC-20-AB User manual

1
Beacon Fire Table
Installation Instructions for Beacon Fire Table
BC-20-AB, BC-20-BG, BC-20-MNB, BC-20-WO
BD-20-BG, BD-20-MNB, BD-20-WO

2
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
Contents
Required Tools………………………………….........2
Included with your Fire Pit (Supercast)……..3
Included with your Fire Pit (Granite)………...4
Assembly Instructions……………………………….5
CF-SPARKER Installation…………………..……….5
Supercast Top Placement……………………….…6
Granite Top Installation…………………………….7
Gas Connections……………………………………….8
Burner Installation……………….……….………….9
Electrode Installation…………….…………….…..9
Drawer Operation and
Propane Tank Installation……………………….10
Fire Media Installation……………………….…...11
Burner Cover Installation………………..……....11
Operating Instructions..…………………………...12
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Two people are recommended for
this installation
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
42494 REV B 09-17-18

3
Beacon Metal Base
(Control Valve Installed)
Marbleized Noche Supercast
Top
White Onyx Supercast Top
Adhesive Foam Pads
(X4)
Ø20” Crystal Fire Burner
CF-20
Refer to Crystal Fire Manual for items included with crystal fire burners.
Included with Your Fire Table
(Supercast Top: BC-20-MNB, BD-20-MNB, BC-20-WO, BD-20-WO)

4
Beacon Metal Base
(Control Valve Installed)
Aluminum Frame and
Granite (4 pcs.)
Attachment bracket for
aluminum frame (X4) (for
granite top installations
only)
+
Self-Drilling Screws (X12)
Ø20” Crystal Fire Burner
CF-20
Included with Your Fire Table
(Granite Top: BC-20-AB, BC-20-BG, BD-20-BG)
Refer to Crystal Fire Manual for items included with crystal fire burners.

5
CF-SPARKER
Do not discard any packaging until assembly is complete and unit is
tested. Keep all included manuals in a safe place for future reference.
Warning: Exposed edges may be sharp, use leather gloves when
removing packaging and handling the base. Do not remove protective
cardboard packaging until you have placed the fire pit in its desired
final location.
Assembly Instructions
Locate CF-SPARKER inside of crystal fire burner box.
Remove CF-SPARKER cap and hex nut. Insert AAA battery
(not included) with + end out.
Install CF-SPARKER into control panel as shown below.
Depress CF-SPARKER button to test your sparker.
Un-packaging
1.
Base Placement
2.
CF-SPARKER Installation
3.
Place base in desired final location.
Place on a hard, flat surface. Avoid soft surfaces and
areas that collect water.
Refer to Crystal Fire Manual included with your
Crystal Fire Burner for safety information regarding
the placement of your fire pit.

6
Caution: Top is heavy, two people are required to lift and set into place.
•Remove burner cover before lifting the top to
avoid damage to the cover.
•Carefully lower top onto base. Position top so
it is centered on top of the base.
Supercast Top Placement
4.a.
Refer to this step for grey table bases with Supercast Tops: (BC-20-WO, BD-20-WO)
Refer to this step for brown table bases with Supercast Tops: (BC-20-MNB, BD-20-MNB)
•Remove burner cover before lifting the top to avoid
damage to the cover.
•Place adhesive foam pad on top of each leg.
•Carefully lower top onto base. Position top so it is
centered on the foam support pads.

7
4.b.
Granite Top Installation
•Locate Top Attachment Brackets (4) and self-drilling screws (12) included
in the manual bag.
•Screw one attachment bracket to the top of each leg, oriented so the
open channel is towards the center of the base.
•Lower the Aluminum Frame onto the base, align the frame with the 4
mounting brackets.
•Secure frame in place by using two (2) self drilling screws on each bracket.
Refer to this step for tables with granite tops: (BC-20-AB, BC-20-BG, BD-20-BG)

8
Read and understand your Crystal Fire owner’s manual before beginning burner
hookups or using the device. Do not use Teflon tape or pipe dope on flare fittings.
• Ensure valve is in the OFF position before making any gas connections.
• For propane tank installations, install included propane hose and regulator to the
control panel as shown below. Use two wrenches to ensure a gas tight connection.
•For hard piped installations, connect the gas supply line (not included) to the 3/8”
male flare fitting on the valve. Use two wrenches to ensure a gas tight connection.
TIGHTEN CONNECTION
SECURELY WITH WRENCH
Gas Connections
5.
Propane regulator
Or gas supply line

9
Plug both BLACK wires hanging from the burner into the back of the CF-
SPARKER. If an orange wire is present, do not use it. The orange wire is for
Direct Spark Ignition system only.
Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire Burner Owner’s Manual if the
spark is weak, intermittent, or not present.
TIGHTEN ALL CONNECTIONS SECURELY WITH TWO WRENCHES
• Orient burner so electrode is nearest to the control panel
in order to make CF-SPARKER box connections.
Burner Installation
6.
•Ensure the correct orifice is installed for the fuel type you
are using (see Crystal Fire Burner Owner’s Manual included
with burner for orifice sizing information).
•Ensure flex line is securely tightened to the orifice. Use two
wrenches as shown.
One wrench on the flex line and one on the orifice for
counter torque.
•Connect flex line from the burner to the control valve on the base.
TIGHTEN CONNECTION
SECURELY WITH TWO
WRENCHES
• Carefully place burner into burner opening.
Electrode Installation
7.
Flex line from burner
IMPORTANT Please consult your Crystal Fire instruction manual for detailed instructions and important
information related to the burner installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE
OWNER’S MANUAL.

10
•Pull the handle attached to the access drawer to slide access drawer out from
table. Pull drawer out until it stops along the slider track, as shown below.
With the propane tank valve and fire pit valve off, attach the propane regulator
to the propane tank. Hand tighten, do not use a wrench for this connection.
Ensure no hoses or wires are contacting the bottom of the burner.
Push the access drawer with propane tank back into the base, as shown below.
Drawer Operation and Propane Tank Installation
8.
NOTE: Over time the bearings in the
door glides may require Re-greasing.
Perform re-greasing once a year to
maintain the smooth operation of the
slides. To re-grease the slides, spray any
spray lubricant, such as WD-40, into the
bearings as you slide the drawer back
and forth.
•Tilt propane tank and lower into drawer from the side.