Outdoor GreatRoom Company BRON52-K User manual

Installation Instructions for Bronson Pit Table
BRON52-K
Bronson Fire Pit
outdoorrooms.com

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner
installation including: lighting and operating instructions, safety
information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER
WITHOUT CONSULTING THE CRYSTAL FIRE®PLUS
OWNER’S MANUAL.
CONTENTS
1. About Your Fire Table 2
a. Required Tools
outdoorrooms.com42528 REV A 02-22-21
!!
1
b. Included With Your Fire Pit
3. Assembly Instructions
a. Unpacking
b. 1-3 Brick Row Assembly
d. Control Panel Assembly
e. Thermocouple Installation
c. CF-SPARKER Assembly
2. Setting Up Your Burner
f. Electrode Installation
4. Finishing Fire Pit
a.Control Panel Attachment
b. Final Layer Assembly
c. Fire Media Installation
5. Operating Instructions
6. Warnings
7. Warrenties
4
3
9
11
12
13

outdoorrooms.com 2
Refer to Crystal Fire®Plus manual for items included with Crystal Fire®Plus burners
• Utility Knife
To cut and remove packaging
• 2 Open Ended Wrenches
To secure gas connections
•Phillips Screw Driver (Do not use a drill to assemble)
For assembly
• One AAA Battery (Not Included)
Required for electric spark igniter installation
A. REQUIRED TOOLS
B. INCLUDED WITH FIRE PIT KIT
1. ABOUT YOUR FIRE TABLE
BI28 Burner and Accessories
(1)
7.75” X 5.50” X 4.00” Brick
(84)
Capstone (Optional)
(4)
Vent Block (10394)
(2)
34” Whistle Free
Stainless Steel
Flex Line (10367)
(1)
Control Panel Block (10393)
(1)
Control Panel (10259)
(1)
42 Inch Round Burner Plate (BP42RD)
(1)
5.50
7.75
8.00
4.00

outdoorrooms.com 3
SETTING UP YOUR BURNER
ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before
beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
A. GAS CONNECTIONS
2.
•For hard piped installations. Connect the gas supply line (not included) to
the 3/8” male are tting on the valve.USE TWO WRENCHES TO ENSURE A
GAS TIGHT CONNECTION.
!
!
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE®PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE®PLUS OWNER’S MANUAL.
!!
• See Crystal Fire®Plus instructions for burner installation.
• All gas connections were completed at the factory.
• Check all connections for leaks. If needed, tighten connection with 2 wrenches
and re-check for leaks.

ASSEMBLY INSTRUCTIONS
A. UNPACKING
Do not discard any packaging until assembly is complete and unit is
tested. Keep all included manuals in a safe place for future reference.
Keep bricks stacked until ready to be placed.
WARNING
Exposed edges may be rough, use leather gloves
when removing packaging and handling the bricks.
B. 1-3 BRICK ROWS ASSEMBLY
3.
outdoorrooms.com 4
1. Once desired location for re pit has been determined, start with
placing rst layer of bricks. Follow the diagram shown below for layout
pattern.
!!
FRONT
LAYER 1

outdoorrooms.com 5
2. Continue on to second row of bricks. This layer will contain the 2
vent blocks (included in kit) and the control panel block (included in
kit). Follow diagram shown below for layout pattern.
FRONT
LAYER 2
VENT BLOCK
3. Continue on to third row of bricks. Follow diagram shown below for
layout pattern.
VENT BLOCK
CONTROL PANEL BLOCK
FRONT
LAYER 3

outdoorrooms.com 6
4. Unpack burner. Before installing the burner into the burner plate,
remove the 24 inch ex line between burner oriface and valve and
connect included 34 inch ex line. Use 2 wrenches to tighten and
perform leak test. Set burner into burner plate.
Position burner plate in center of re pit and then pull plate so that end
is slightly o edge. Leave a gap bewteen control panel block and
burner plate so that hands are able to t and make connections outlined
in future steps.
WORKABLE GAP
BURNER PLATE
AND BURNER

outdoorrooms.com 7
• Pull the VCSV valve through the back and then front opening of the
control panel block.
• Connect a whistle free exible gas supply line to the inlet of valve us-
ing a ½” are nut.
• Attach burner valve to control panel with provided screws.
Ensure CF-SPARKER is installed before this step.
D. CONTROL PANEL ASSEMBLY
C. CF-SPARKER ASSEMBLY
• Locate CF-SPARKER inside of Crystal Fire® Plus burner box.
• Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included)
with + end out.
• Install CF-SPARKER into control panel as shown below. CF-SPARKER must be
installed BEFORE control valve.
• Press in CF-SPARKER button to test your sparker.
CF-SPARKER
MAIN GAS SUPPLY
BURNER WHISTLE FREE
SUPPLY FLEX LINE
VCSV
CTRL PANEL

outdoorrooms.com 8
C. ELECTRODE INSTALLATION
• Plug both BLACK wires hanging from the burner into the back of the
CF-SPARKER. If an orange wire is present, DO NOT USE IT. The orange wire is
for Direct Spark Ignition system only.
• Test system by pushing the button on the igniter. Consult the troubleshooting
section of the Crystal Fire® Plus owner’s manual if the spark is weak,
intermittent or not present.
E. THERMOCOUPLE INSTALLATION
SEE DETAIL B
SEE DETAIL A
SCALE 0.800
DETAIL A
SCALE 0.800
DETAIL B
•Refer to Crystal Fire® Plus instruction manual for detailed attachment
of thermocouple.
• Attach thermocouple to burner valve as shown below.
ELECTRODE WIRES
*Flexline removed in
image for visibility.

outdoorrooms.com 9
Move burner and burner plate back towards center of re pit. Place
bricks as nal layer. Follow diagram shown below for layout pattern.
Push control panel back into control panel block, making sure all
connections are tucked in and not kinked. Using the 4X provided metal
screws, attach the control panel to the control panel block. Finalize by
pressing the control panel knob onto the stem of the VCSV valve.
B. FINAL BRICK LAYER ASSEMBLY
A. CONTROL PANEL ATTACHMENT
4. FINISHING FIRE PIT
KNOB
SCREWS (4X)
CTRL PANEL
OPTIONAL CAPSTONE SETUP: The BRON52-K has an optional
captone. The capstone can be place on top of layer 3 (replacing the
brick of layer 4) or on top of layer 4. When using the optional
capstone ensure that the burner plate is one layer below the capstone.
FRONTFRONT
LAYER 4 (optional capstone)LAYER 4
CAPSTONE