Outdoor GreatRoom Company Crystal Fire CV-30WT User manual

1
The Cove Fire Pit
Installation Instructions for CV-30

2

3
Contents
Required Tools…………………………….…..2
Included with your Fire Pit……………….3
Assembly Instructions………………….………4
Gas Connections………………………….…….6
Igniter Installation…………….……………...8
Position Your Tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from rough edges
found on fire pit table during
installation.
One AAA battery (not Included)
Required for electric spark igniter
installation
Two people are required for this
installation
Contents
Required Tools………………………………….........3
Included with your Fire Pit………………………..4
Assembly Instructions……………………………….5
Igniter Installation…………………………………….6
Gas Connections……………………………………….6
Glass Installation………………………………………9
Required Tools
Three people are required for this installation.
2 Open Ended Wrenches
To secure gas connections.
Leather Gloves
To protect hands from rough edges found on fire pit
during installation.
One AAA Battery (not included)
Required for electric spark igniter installation.
Utility Knife
To cut and remove packaging.
Power Drill
To remove support board from crate.
IMPORTANT
Please consult your Crystal Fire Burner Owner’s instruction manual
for detailed instructions and important information related to
hooking up your burner, including safety information, proper
tightening of connections with two wrenches, and full burner setup
and lighting instructions.
DO NOT ATTEMPT TO INSTALL CF-30 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE BURNER OWNER’S MANUAL.
42451 REV C 8-20-18

4
Crystal Fire CF-30 Burner Kit
CV-BASE with Key Valve
Control Panel
Key for Key
Valve
Included with your Fire Pit

5
Included with your Fire Pit
A. 4 Fasteners
B. 4 B-Bolts
C. 4 C-Bolts
D. 4 Bolt Caps
E. Touch-Up Paint Bottle
Assembly Instructions
Assembly Instructions
1. First, unscrew the shipping block with a power drill. Discard
board. It will not be needed for further assembly of this
product.
2. Remove fire pit base from the crate you received it in. Place
the base in your desired location. Three people are
recommended for this step of the installation.
1
2
.
.
Shipping Block

6
Igniter Installation
1. Make sure the valve is in the OFF
position before beginning.
2. Remove sparker cap by turning
counter-clockwise and insert a
AAA battery (not included).
Gas Connections
Read and understand your Crystal Fire Burner Owner’s manual
before beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
1. Reach inside the base and attach gas supply line to the
input shown below, using a 3/8” flare fitting.
Propane
input
Natural gas
input

7
TIGHTEN CONNECTION
SECURELY WITH WRENCH
2. Ensure the correct orifices are installed for the fuel type you are using
(see Crystal Fire Burner Owner’s manual included with burner for orifice
sizing information).
1. Reach inside the base and attach gas supply line to
the input shown below, using a 3/8” flare fitting.
TIGHTEN SECURELY WITH TWO WRENCHES
Metal flex line to
burner
3. Attach flex line from the burner to gas valve as shown below.

8
Set burner into the fire pit base as shown below
Sparker
Sparker will not operate correctly without an ignition and ground wire
attached.
Sparker will not operate correctly without an ignition and ground wire attached.
Plug both BLACK wires hanging from the burner into the back of the
sparker box. If an orange wire is present, do not use it. The orange
wire is for automatic ignition system add-on only.

Test system by pushing the button on the igniter. Consult the
troubleshooting section of the Crystal Fire Burner Owner’s Manual, if
the spark is weak, intermittent, or not present.
Igniter Installation (continued)

9
Glass Installation
1. Scatter all the included glass beads evenly onto burner surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT INCLUDED
GLASS BEADS
Glass Installation

10
IMPORTANT
Please consult your Crystal Fire Burner Owner’s instruction manual
for detailed instructions and important information related to
hooking up your burner, including safety information, proper
tightening of connections with two wrenches, and full burner setup
and lighting instructions.
DO NOT ATTEMPT TO INSTALL CF-30 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE BURNER OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks

11
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form/
to register your product.
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made with
pride in the USA.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]