Outdoor GreatRoom Company Sonoma User manual

1 | P a g e
Sonoma/San Juan Fireplace
Installation Instructions
SONFS42-M-K
SANJUANFP

2 | P a g e
Required Tools:
Razor Knife
For cutting packaging
Hammer or Pry Bar
To remove staples from 1x2”
securing boards
Power Drill or Philips Screw Driver
To remove packaging screws
9/16” Deep Socket or Standard
Socket with Extension
To attach top shelf
Leather work gloves
To protect hands from rough
and sharp edges of inner steel
framing
IT IS RECOMMENDED THAT A MINIMUM
OF TWO PEOPLE ASSEMBLE AND INSTALL
THIS FIREPLACE
42425 Rev A-8/18/2011
Congratulations on your purchase of a new
outdoor gas fireplace!
These instructions will help you get your new fireplace set
up in no time. Be sure to thoroughly read your gas burner
instruction manual for important safety information and
special considerations.

3 | P a g e
Unwrapping your Fireplace
1
Using a razor knife, carefully cut plastic
covering fireplace , taking care to avoid
cutting or scraping the unit inside.
Using a pry bar or hammer, pry up staples
holding 1x2” boards to ease fireplace
removal from pallet.
With a minimum of two people, carefully
remove cast concrete top and hearth pad
from fireplace and set aside.
2
3
4
Remove mantel from inside of firebox and
set aside before proceeding to the next step.

4 | P a g e
Removal of Firebox
The cast concrete firebox weights
approximately 150-175lbs and should be
removed before attempting to remove
fireplace from shipping pallet for safety.
With a minimum of two people, carefully slide
firebox forward while lifting slightly . Set aside.
After removing firebox, move fireplace to its final
location.

5 | P a g e
Mounting Shelf
1
Remove supplied bolts from the back of
cast concrete mantel piece.
2
Have another person hold mantel in
place against fireplace surface while you
insert bolts and washers from inside the
fireplace. Using 9/16” socket, tighten
bolts until secure. Cast concrete top can
be set into place at this time as well.
DO NOT OVERTIGHTEN OR USE
MANTEL TO LIFT FIREPLACE

6 | P a g e
Final Assembly
IMPORTANT
Please consult your Crystal
Fire instruction manual for
detailed instructions and
important information
related to hooking up your
CF-1224 burner, including
safety information, proper
tightening of connections
with two wrenches and full
burner setup and lighting
instructions.
DO NOT ATTEMPT TO
INSTALL CF-1224 BURNER
WITHOUT FIRST
CONSULTING THE
MANUAL. IF YOU ARE
UNSURE OF HOW TO
COMPLETE THE STEPS
OUTLINED, CONSULT A
QUALIFIED TECHNICIAN
WARNING
After consulting the
manual and following
instructions, remember;
before operating, all gas
connections must be fully
checked for leaks
With your Sonoma fireplace in the
desired location, drill a small hole
large enough for incoming gas line to
pass through in a side, back, or bottom
of the fireplace, depending on
installation location.
Carefully slide firebox back into the
unit. Slide forward until the back
surface of the fire box meets the front
stucco surface of the fireplace body.
Have a qualified licensed professional
make all gas connections at this time.
This should be done in accordance
with local and national codes.
Slide the hearth pad into place
carefully and evenly. If fit is too tight,
lift firebox slightly while another
person slides hearth pad into the unit.
Install gas burner by gently lowering
into the cutout provided.
Install Logs and accessories as detailed
in the provided instructions for those
products.
1
3
2
5
4
6

7 | P a g e
THIS PAGE INTENTIONALLY
LEFT AWESOME.
2015 Silver Bell Road •Suite 195 •
Toll Free: 1-866-303-4028
Warranty: Your outdoor fireplace is covered
under a 1-year manufacturer’s warranty. Please
visit http://www.outdoorrooms.com/warranty-
form to register your product.

8 | P a g e
© 2011 The Outdoor GreatRoom Company