Oxford Instruments Andor Kymera 193i User manual

Unpack the Spectrograph
2
3
1Prepare your Facility Install Software (SDK2 or Solis)
Kymera 193i Quick Start Guide
Spectrograph Accessories
Kymera 193i
Spectrograph
Power Supply USB 2.0 &
I2C Cables
Grating(s) Camera(s)
(when applicable)
Output Port
Adaptor(s)
Hex Key Set
Documentation
scan or visit:
andor.oxinst.com/
welcome
Software
(copy supplied)
You must have administrator access on your PC to perform this installation.
These instructions cover installation of both Andor Solis and Andor SDK if ordered. A copy of the software is provided
within the spectrograph box. Additionally, the latest software les are available to download on request, please sign
in or create an account at andor.oxinst.com/downloads
Windows: Switch on the PC, run the setup exe from the supplied copy or the downloaded le: e.g. AndorSDK2Setup-
<version>.exe
1. Conrm the version of software (minimum is v2.1.x).
2. Follow the on screen prompts.
3. Select the installation directory when prompted.
4. If prompted for select the required hardware (spectrograph and/or camera) type.
5. On the nal window click on “Install”. Continue to follow the on screen prompts.
Kymera will require SDK2 or Solis installation, please see quick start guide for specic camera
model software requirements.
Online access to technical documentation is available at: andor.oxinst.com/downloads
Please follow these guidelines when unpacking the Kymera:
1. The Kymera should be placed in the environment it will be
used in for a few hours before adjustment and rst use.
2. Environment should be dust free.
3. Spectrograph should be placed on a at, stable support
(e.g. optical table); Spectrograph feet are designed to be
secured on an optical table with appropriate screws.
The Kymera can be supplied with a range of accessories as specied at the
time of ordering. Please check the supplied items against the packing list to
ensure all items are present.
Handle the spectrograph, camera and
accessories with care. The 193i weighs 7.5
kg [16 lb 5 oz].
Use correct power supply and cables.
Observe anti-static precautions
when installing the spectrograph and
accessories.
Operate at a constant temperature between
0°C and 30°C (temperature uctuation during
operation may result in calibration drift).
Store between -25°C and 50°C.
Ensure sucient clearance around
spectrograph and power supply vents
(Do not block vents when operating on
benchtop).
Keep dry, <70% humidity non-condensing.
Operation of the spectrograph close
to intense pulsed sources (e.g. plasma
and X-ray sources) may compromise
performance.
Refer to the user manual for further information

Set up Solis on the Kymera 193i
MAN-09416
SR193QSG 1021 R1
1. The 193i should be connected to the camera by either:
• I2C cable (supplied, if applicable), or
• USB cable (provided).
2. If your spectrograph has a shutter, then this is controlled through the I2C cable (if used for the
connection), or through the BNC connection via a cable from the camera (supplied), or for simple open/
close operation no connection is required.
3. The 193i accessories - motorised slits, lter wheel, shutter - are all ‘plug and play’ and do not require
any setup.
Connect the Camera and Spectrograph
Refer also to the Kymera 193i user guide Conguring Solis for the Kymera 193i
1. Power on the Kymera 193i and if appropriate
the detector, wait until the short start-up tone
signals it has nished system checks.
2. Start Solis.
3. Solis will auto detect the Kymera and show a
dialog on startup alerting the user of this.
4. Once fully loaded the Spectrograph
control UI will show with the auto detected
peripheral controls.
5. Please refer to your camera and Kymera
193i user manuals for any further setup or
calibration steps required before using your
system.
Connect the Camera to the PC
5
Troubleshoot
Spectrograph is not recognised by Solis
• Ensure that the Kymera 193i has nished its system checks before attempting to connect with it.
Check the connections between the camera, PC and spectrograph.
Camera is not recognised by PC
• Check that the camera power and USB cable are connected securely and the mains power cable is inserted.
• Check that the drivers have been installed properly
(Control Panel /System/Hardware /Device Manager /Imaging Devices).
Shutter is not opening
• The shutter should always be controllable open/closed in the Solis GUI (when shutter is present). When the I2C
cable or the BNC input is used, the ‘BNC’ option should be selected in the software to enable operation of all
shutter modes.
• Check opening/closing times have been properly setup.
Turret lid dicult to open
• Rotate the lid lock from the locked to the unlocked position.
• The turret lid can then be lifted up using the handle of the turret lid.
Communication error when selecting side port
• When shipping, a locking screw is used to secure the ipper mirror in dual exit systems (KYMERA-193i-Bx). This
needs to be loosened fully or removed before use.
Please see the Hardware Guide for further information on Troubleshooting.
Online access to technical documentation is available at: andor.oxinst.com/downloads
?
6
I2CUSB
Shutter (BNC)
Accessory
Connector
(e.g. lter
wheel)
Connection Panel of the Kymera 193i
Note: If your 193i is a dual exit system (model KYMERA-193i-Bx), then you must loosen fully or remove the
locking grub-screw used during shipping to hold the ipper mirror in place.
Power
Input
Power Switch
Flipper
mirror
locking
screw
Above Accessories are automatically detected and
displayed in the Solis software.
Connect the Camera to the PC
Depending on the camera model supplied there are three types of possible connectivity between the camera and
the PC:
• USB 2.0 or 3.0
• USB 2.0 or 3.0 and I2C
• Cameralink
Note for Newton, iDus, iVac and iStar models the I2C connection is strongly recommended.
Please refer to the Quick Start Guide provided with the Andor camera for full installation directions applicable to
the specic camera model.
Note that if camera is ordered for the second output port, it will arrive detached and attach-
ment procedure as per user manual must be followed.
Ensure that the camera AND the PC are switched OFF.
A pre-aligned camera and spectrograph package comes pre-tted with a ange. For a standalone spectrograph,
the unit is supplied with a camera ange, the camera must be attached to the ange and the ange attached to
the spectrograph body with the screws supplied. Please see the spectrograph user guide for mounting information.
4