Panasonic MX-101SG1WTN User manual

© Panasonic Corporation 2010 Unauthorized copy-
ing and distribution is a violation of law.
Order No. PTW1004510CE
Blender
Model No. MX-101SG1WTN
Model No. MX-101SG1WTM
Chassis
Product Color White
Destination WTN: PGF, UAE WTM:
Qatar, Oman
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 3
3 Location of Controls and Components ------------------- 4
4 Operating Instructions------------------------------------------ 6
4.1. How to Use Blender--------------------------------------- 6
4.2. How to Use Dry & Wet Mill------------------------------ 8
4.3. How to Clean ----------------------------------------------10
5 Troubleshooting Guide----------------------------------------11
6 Disassembly and Assembly Instructions ---------------12
6.1. Juice cup and Cutter Assy -----------------------------12
6.2. Mill cup and Cutter Assy -------------------------------13
6.3. Bottom plate -----------------------------------------------14
6.4. Connector(Lower) ----------------------------------------14
6.5. Cord U -----------------------------------------------------15
6.6. Motor Assy------------------------------------------------- 15
6.7. Brush Assy------------------------------------------------- 15
6.8. Switch Assy------------------------------------------------16
6.9. Safety unit--------------------------------------------------16
7 Wiring Connection Diagram---------------------------------17
7.1. Schematic diagram--------------------------------------17
7.2. Basic wiring diagram------------------------------------18
8 Exploded View and Replacement Parts List-----------19
8.1. PARTS LOCATION--------------------------------------19
8.2. REPLACEMENT PARTS LIST -----------------------20
8.3. PACKING INSTRUCTION-----------------------------21

2
1 Safety Precautions

3
2 Specifications
MX-101SG1WTN / MX-101SG1WTM
Using blender Using dry & wet mill
Power supply 220-240V 50-60Hz
Power Consumption 180-205W
Operation rating Continuous (Repetition 3 min. ON, 1 min. OFF) 90 seconds at time
Container capacity Maximum 1,000ml Dry: Maximum 50g / Wet: Maximum 200ml
Container material Glass Glass
Dimensions (H x W x D) approx. 36.0 x 17.0 x 20.6cm approx. 25.8 x 15.1 x 20.6cm
Weight approx. 2.7kg approx. 1.9kg

4
3 Location of Controls and Components

5

6
4 Operating Instructions
4.1. How to Use Blender

7

8
4.2. How to Use Dry & Wet Mill

9

10
4.3. How to Clean

11
5 Troubleshooting Guide
Symptom Possible Cause Countermeasure
• Motor fails to Armature Assy Or humming
noise is head 1. Motor(Armature Assy. Field Assy) defec- tive.
2. Wiring connection improper
3. Switch defective
4. Cord U broken
5. The current breaking function of switch
is on
6. Motor short-circuitted
7. Wear of Brush Assy
1. Replace Motor
(Armature Assy, Field Ass'y)
2. Correct it
3. Replace Switch
4. Replace Cord U
5. Push “OFF” and then “ON” of Switch
6. Replace Motor
(Armature Assy, Field assy)
7. Replace the two Brush Assy at the same
time
• Cutter Assy fails to rotate 1. Cutter Assy shaft seizes up
2. Wear of Connector 1. Replace Cutter Assy and Cup Base Assy 2. Replace Connector(Upper or lower)
• Noises and vibrations are observed 1. Fastened conditions of screws improper
2. Cutter Assy deformed
3. Motor Shaft eccentric
4. Assembly of Juice Cup improper or fas-
tened conditions of Cup Base Assy to
Juice cup improper.
1. Fasten tightly
2. Replace Cutter Assy
3. Replace armature Assy
4. Reassemble properly
• Juice or other material leaks 1. Juice cup cracked
2. Packing improperly fixed
3. Packing damaged
4. Juice cup and Cup Base Assy insuffi-
ciently fastened
1. Replace Juice cup
2. Properly fix Packing
3. Replace Packing
4. Fasten them firmly
• Current Breaking Function of Switch Assy
fails and cause motor burning Breaker of Switch Assy short-circuited Replace both Motor(Armature Ass'y and Field Assy) and Switch Ass'y

12
6 Disassembly and Assembly Instructions
6.1. Juice cup and Cutter Assy
1. Remove the cover, then turn the Juice cup up-side-down.
2. Secure the Juice cup and turn the cup base Assy counter
clockwise. Then the packing can be removed.
3. Turn the connector upper clockwise with long nose pliers.
Then the Cutter Assy and connector upper can be
removed.

13
4. Uses a minus driver and it removes a safety device by the point of the lever. (Make not lose a spring.)
6.2. Mill cup and Cutter Assy
1. Secure the mill cup and turn the cup base Assy counter
clockwise. Then the mill packing can be removed.
2. Turn the connector upper clockwise with long nose pliers.
Then the Cutter Assy and connector upper can be
removed.

14
3. Uses a minus driver and it removes a safety device by the
point of the lever. (Make not lose a spring.)
6.3. Bottom plate
1. The bottom plate can be removed when its four screws
are lossened.
6.4. Connector(Lower)
1. Hold the part under the motor shaft by means of a
screws-driver, then turn the connector (lower) clockwise.
The connector (lower) can be removed.
• The connector (lower) can be relatively easily removed
by means of hitting its projecting section clockwise with
use of a screwdriver grip in a forceful manner.

15
6.5. Cord U
1. Pull out while the faston terminal with the part of the Cord
U.
6.6. Motor Assy
1. Takes out a motor from the body and it removes.
The brush can be exchanged by metal fittings coming
when bending fixation metal fittings.
6.7. Brush Assy
1. Inserts a minus driver in a draught of the brush folder and
the brush fixation metal fittings in the motor.
• When inserting a whisk, it is possible to put either side of the
board of the fixation metal fittings in the brush folder by hold-
ing it.

16
6.8. Switch Assy
1. Take out a switch from the body and remove it.
6.9. Safety unit
1. Safety unit can be removed when its a screw is lossened.

17
7 Wiring Connection Diagram
7.1. Schematic diagram

18
7.2. Basic wiring diagram

19
8 Exploded View and Replacement Parts List
8.1. PARTS LOCATION

20
8.2. REPLACEMENT PARTS LIST
Notes:Important safety notice
• Components identified by mark have special characteristics important for safety.
• " When replacing any of these components use only manufacturer's specified parts."
MODEL No.MX-101SG1WTN / MX-101SG1WTM
Safety Ref. No. Part No. Part Name & Description Pcs/Set Remarks
WTN WTM
<PARTS LIST>
1 X0190-360 Cup assy 1 1
2 X0201-181 Cover 1 1
3 X03BR6300 Cup 1 1
4 VE06-1842 Packing 1 1
5 X0195-160 Cup base assy 1 1
6 X0224-180 Cutter assy 1 1
7 X0217-010 Wave washer 2 2
8 X0227-031 Main shaft washer 2 2
9 X0194-010 Cup base U 1 1
10 X0240-010 Spring(Cup) 3 3
11 X0213-050 Safety device lever 1 1
12 X0227-060 Shaft washer 2 2
13 X0411-100R Connector (upper) 2 2
14 X0190-350 Cup assy(mill) 1 1
15 X0203-170 Mill cup 1 1
16 X0205-070 Mill packing 1 1
17 X0195-150 Cup base U assy(mill) 1 1
18 X0224-100 Mill cutter assy 1 1
19 X0191-020 Mill cup base U 1 1
20 VE18-184 Spring(Mill) 3 3
21 X0213-060 Safety device lever 1 1
22 VB99-1841 Connector (lower) 1 1
23 X0110-530 Body U 1
23 X0110-540 Body U 1
24 X0214-010 Safety device cover 1 1
25 X0525-020 Spring plate 1 1
26 X0175-020 Attention sheet 1 1
27 X0104-010 Seal cap 1 1
28 XTN4+10BFJ Screw 1 1
29 X0505-040 Safety device pin 1 1
30 X0501-410 Switch assy 1 1
31 X0103-020 Body cover gum 3 3
32 X0701-590 Motor assy 1 1
33 53-029086 Brush assy 2 2
34 X0550-920 Cord U 1 1
35 X0130-170 Bottom plate 1 1
36 X0133-020 Leg 3 3
37 XTN4+16BFJ Screw 4 4
38 X0173-530 Name plate 1
38 X0173-540 Name plate 1
39 X0420-030 SCRAPER 1 1
<PACKING SPECIFICATIONS>
X0903-930 Outer carton 1
X0903-940 Outer carton 1
X0911-290 Protection A 1 1
X0912-290 Protection B 1 1
X0917-010 Paper Plate 1 1
X0909-910 Operating instructions 1 1
XZB18X24A03 Plastic bag 1 1 For cord
XZB10X50A03 Plastic bag 1 1