Panasonic MX-151SG2WTN User manual

© Panasonic Corporation 2010 Unauthorized copy-
ing and distribution is a violation of law.
Order No. PTW1007514CE
Blender
Model No. MX-151SG2WTN
Model No. MX-151SG2WTM
Model No. MX-151SG2WTB
Model No. MX-151SG2WTH
Chassis
Product Color White
Destination WTN : UAE , PGF
WTM : Oman
WTB : Saudi Arabia
WTH : Kuwait
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 3
3 Location of Controls and Components ------------------- 4
4 Operating Instructions------------------------------------------ 6
5 Troubleshooting Guide----------------------------------------16
6 Disassembly and Assembly Instructions ---------------17
7 Wiring Connection Diagram ---------------------------------23
8 Exploded View and Replacement Parts List -----------25

2
1 Safety Precautions

3
2 Specifications
MX-151SG2
When the blender is used When the dry mill is used
Power supply 220-240V 50-60Hz
Power Consumption 205-225W
Rated duration Continuous (Repetition 3 min. ON, 1 min. OFF) Continuous (Repetition 3 min. ON, 1 min. OFF)
Container material Glass Plastic
Dimensions (H x W x D) Approx. 40.0 x 19.4 x 24.4cm Approx. 25.1 x 18.3 x 24.4cm
Weight Approx. 3.3kg Approx. 1.8kg

4
3 Location of Controls and Components

5

6
4 Operating Instructions
4.1. How to Use Blender

7

8

9
4.2. How to Use Dry Mill

10

11

12
4.3. Safety

13

14
4.4. How to Clean

15

16
5 Troubleshooting Guide
Symptom Possible Cause Countermeasure
• Motor fails to Armature Assy Or humming
noise is head 1. Motor(Armature Assy. Field Assy) defec- tive.
2. Wiring connection improper
3. Switch defective
4. Cord U broken
5. The current breaking function of switch
is on
6. Motor short-circuitted
7. Wear of Brush Assy
1. Replace Motor
(Armature Assy, Field Ass'y)
2. Correct it
3. Replace Switch
4. Replace Cord U
5. Push “OFF” and then “ON” of Switch
6. Replace Motor
(Armature Assy, Field assy)
7. Replace the two Brush Assy at the same
time
• Cutter Assy fails to rotate 1. Cutter Assy shaft seizes up
2. Wear of Connector 1. Replace Cutter Assy and Cup Base Assy 2. Replace Connector(Upper or lower)
• Noises and vibrations are observed 1. Fastened conditions of screws improper
2. Cutter Assy deformed
3. Motor Shaft eccentric
4. Assembly of Juice Cup improper or fas-
tened conditions of Cup Base Assy to
Juice cup improper.
1. Fasten tightly
2. Replace Cutter Assy
3. Replace armature Assy
4. Reassemble properly
• Juice or other material leaks 1. Juice cup cracked
2. Packing improperly fixed
3. Packing damaged
4. Juice cup and Cup Base Assy insuffi-
ciently fastened
1. Replace Juice cup
2. Properly fix Packing
3. Replace Packing
4. Fasten them firmly
• Current Breaking Function of Switch Assy
fails and cause motor burning Breaker of Switch Assy short-circuited Replace both Motor(Armature Ass'y and Field Assy) and Switch Ass'y

17
6 Disassembly and Assembly Instructions
6.1. Juice cup and Cutter Assy
1. Remove the cover, then turn the Juice cup up-side-down.
2. Secure the Juice cup and turn the cup base Assy counter
clockwise. Then the packing can be removed.
3. Turn the connector upper clockwise with long nose pliers.
Then the Cutter Assy and connector upper can be
removed.

18
4. Uses a minus driver and it removes a safety device by the
point of the lever. (Make not lose a spring.)
6.2. Mill cup and Cutter Assy
1. Secure the mill cup and turn the cup base Assy counter
clockwise. Then the packing can be removed.
2. Turn the connector upper clockwise with long nose pliers.
Then the Cutter Assy and connector upper can be
removed.

19
6.3. Bottom plate
1. The bottom plate can be removed when its four screws
are lossened.
6.4. Connector(Lower)
1. Hold the part under the motor shaft by means of a
screws-driver, then turn the connector (lower) clockwise.
The connector (lower) can be removed.
• The connector (lower) can be relatively easily removed
by means of hitting its projecting section clockwise with
use of a screwdriver grip in a forceful manner.
6.5. Cord U
1. Pull out while the faston terminal with the part of the Cord
U.

20
6.6. Motor Assy
1. Pull out while the faston terminal with the part of the Lead
wire.
2. Takes out a motor from the body and it removes.
The brush can be exchanged by metal fittings coming
when bending fixation metal fittings.
6.7. Brush Assy
1. Inserts a minus driver in a draught of the brush folder and
the brush fixation metal fittings in the motor.
• When inserting a whisk, it is possible to put either side of the
board of the fixation metal fittings in the brush folder by hold-
ing it.