Panasonic MX-MG5351 User manual

English
Melayu
Model No.
Operating Instructions
Arahan Penggunaan
Pengisar (Kegunaan rumah tangga)
Blender (Household Use)

EN2
Safety Precautions .............................................................................................................................. EN2
Important Information ......................................................................................................................... EN4
Parts Names and Instructions ........................................................................................................... EN5
Overload and Overheating Protection .............................................................................................. EN5
Before Use ............................................................................................................................................ EN6
How to Use ........................................................................................................................................... EN6
Cleaning and Care ............................................................................................................................... EN7
Troubleshooting .................................................................................................................................. EN8
...................................................................................................................................... EN8
The following signals indicate the degree of harm and damage when the product is misused.
WARNING:
Indicates potential hazard that could result in serious injury or death.
CAUTION:
please give your special attention to "Safety Precautions" and
"Important Information" (P. EN2 - EN4).
these instructions.
Contents
WARNING
Do not allow infants and children to play with packaging material.
Do not disassemble, repair or modify this appliance.
Do not damage the power cord or power plug.
/
Safety Precautions
these
instructions.

EN3
English
Do not plug or unplug the power plug with wet hands.
Do not use the appliance if the power cord or power plug is damaged or the power plug is
loosely connected to the outlet.
Do not immerse the motor housing, power cord or power plug in water, or splash it with
water and / or any liquid.
This appliance is not intended for use by persons (including children) with reduced
physical,
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Keep the appliance and its power cord out of reach of children.
Discontinue using the appliance immediately and unplug in the unlikely event that this
appliance stops working properly.
There is an unpleasant smell.
Make sure the voltage indicated on the label of the appliance is the same as your local supply.
Be careful if hot liquid is poured into the blender jug as it can be ejected out of the
appliance due to a sudden steaming.
Do not use the appliance on the following places.
Do not blend or place over 60 °C ingredients into blender jug or mill container.
jug while the appliance is operating.
WARNING
CAUTION

EN4
Do not use the appliance outdoors.
Do not use the appliance for commercial purpose.
Do not stretch the gasket to avoid deforming.
Do not replace any parts of the appliance with non-genuine spare parts.
Do not carry the appliance by holding the power cord, blender jug or mill container.
Do not insert any object in the gaps of the appliance.
Do not blend more than the working capacity marked on the blender jug. For the mill
)
Do not use prohibited ingredients as stated in this instructions. (P. EN6)
Do not push the safety lock pin with any implement, such as thin stick etc. (P. EN5)
Unplug the plug when the appliance is not in use.
Make sure to hold the power plug when unplugging it. Never pull on the power cord.
Beware not to trip over or get caught in the power cord while in use.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this
Care shall be taken when handling the sharp blades, emptying the blender jug, mill
container and during cleaning. Do not clean the blender blade or mill blade by bare hand.
Always disconnect the appliance from the supply if it is left unattended and before
assembling, disassembling, moving or cleaning.
approaching parts that move in use.
)
Ensure to clean the appliance especially surfaces in contact with food after use. (P. EN7
"Cleaning and Care")
This product is intended for household use only.
CAUTION
Important Information
Safety Precautions
these
instructions.

EN5
English
Parts Names and Instructions
Control
Motor
Overload and Overheating Protection
In case of overload and overheating, the protection device is triggered to stop operation and it is not abnormal.
After rotation stops, follow the below steps:
1
Press "0" button, unplug the appliance.
2
jug, it also can add liquid.)
3
Reset the attachment, then start again.
If the appliance still does not operate after performing the above, overheating protection has been activated.
Press "0" button, unplug and rest the appliance for about 15 minutes or more (until motor housing returns to a normal temperature) to
release overheating protection before using again.
MX-MG5351 Glass
The Safety Lock has been designed to prevent the appliance from switching on when blender jug or mill container is not properly in place.
Note:
• Do not push the Safety Lock Pin and any Safety Levers with any instrument such as stick.
• Do not pour liquids or ingredients at the Safety Lock Pin and Control Panel area.
• Keep the Safety Lock Pin and Safety Lever area clean to avoid foreign particles accumulating in the area.
Control Panel
Ice Crush
Crush
Mill Container
Mill Gasket
Mill Blade
Mill Container Base
Illustrations of product in this
Blender Gasket
Blender Blade
Blender Wet & Dry Mill

EN6
Before Use
, and then
assemble them securely. (P. EN6 "How to Use" and P. EN7 "Cleaning and Care" )
Handling Precautions Handling Precautions
Dice food first (1 -
more than 1/3 full nor operate more than 2 minutes.
mill container.
How to Use
To disassemble To assemble
To disassemble To assemble
Guide of Menus and Functions
Blender Wet & Dry Mill
Blender Wet & Dry Mill
1
2
1
2
1
2
1
2
Mill
Mill container
Function Menu Speed Quantity Operating Time Preparation Method
Blender
1
1
For porridge:
For boiled spinach:
- Boil the spinach more than 5 minutes to soften it.
For boiled carrot:
For all menus:
1
Boiled Carrot 1
Blend until there
is no sound. -
2 -
2
For Smoothie:
Wet & Dry
Mill
Coffee Beans 2 -
2 -
Dried Chilli 2
Fresh Chilli 2 -

English
4
switch off by pressing the “0”
button. Unplug.
Turn the mill
container
anticlockwise to
remove it, open
the mill container,
and take out the
ingredients.
1
Turn the mill container upside down and place the
ingredients in it. Twist the mill container base clockwise until
you hear a click sound.
2
Attach blender jug to the motor housing
.
1
Place the ingredients into blender jug, and then close the lid.
hear a click sound.
3
Plug in. Hold the lid, and then turn
on the appliance by pressing the
required speed.
on the motor
on the mill
until you hear a click sound.
2
Attach the mill container to the motor housing.
3
Plug in. Hold the mill container, and then
turn on the appliance by pressing the
required speed.
4
switch off
by pressing the “0” button. Unplug.
Turn the blender jug anticlockwise to
remove it, open the lid
and take out the
ingredients.
Containers and Other Parts Blades Motor Housing
Wash the parts using a soft sponge soaked in diluted kitchen
detergent (neutral). Rinse and dry thoroughly. (
Wipe motor housing with a
damp cloth.
Cleaning and Care
How to use the scraper
Scraper is useful when
Carefully clean blades with a
brush under running water.
(
Blender Jug Prewash Storing
Unlock
1
2
1
2
3
4
1
2
4
32
1
Unlock
1
2
31
2
3
3

Blender Wet & Dry Mill
Power supply
Power consumption
Rated time
Continuous operation (Repeat the cycle of 3 Continuous operation (Repeat the cycle of 1
Working capacity Dry
MX-MG5351
Before calling for service, please check through this section.
Problem Cause and Action
Troubleshooting
The appliance does
not turn on.
The blender jug / mill container is not set properly.
/
The blender jug base / mill container base is not assembled tightly.
The protection device of overload or overheating is activated.
The power plug is disconnected.
Rotation stops
abruptly.
The protection device of overload or overheating is activated.
There is abnormal
noise or vibration
increases.
The Rubber Feet and/or the work top are not clean.
flat surface.
Too much ingredients.
The blender jug base / mill container base is not assembled tightly.
consistency of
the processed
ingredients do not
turn out well.
Some ingredients might be too difficult to process raw, e.g. pumpkin.
Ingredient size is not according to the preparation method.
The ingredient is
leaking.
The blender jug base / mill container base is not assembled tightly.
The blender gasket / mill gasket is not attached or attached loosely.
Attach it properly.
Foreign matters are stucked around blender gasket / mill gasket.
The blender gasket / mill gasket is damaged.
The blade is idling.
The liquid amount is not enough.
Too much ice cubes.

SC2

SC3