Panasonic MK-G1350PWTX User manual

© Panasonic Corporation 2010 Unauthorized copy-
ing and distribution is a violation of law.
Order Number KAD1010003CE
Meat Grinder
Model No. MK-G1350PWTX
Destination PGF
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Location of Controls and Components ------------------- 3
4 Operating Instructions------------------------------------------ 4
5 Troubleshooting Guide----------------------------------------- 7
6 Disassembly and Assembly Instructions ---------------- 8
7 Wiring Connection Diagram ---------------------------------11
8 Exploded View and Replacement Parts List -----------12

2
1 Safety Precautions
CAUTION
Do not grind too hard meat. If the grinder gets stuck, do not force meat into it.
CAUTION
You may feel the feed screw vibrating during use. It is not a trouble. Do not over tighten the locking knob.
CAUTION
Keep in mind that some parts of the grinder cannot be washed in a dishwasher.
CAUTION
This meat grinder is for home use only.
2 Specifications
Model No. MK-G1350P
Power supply 220-240V 50-60Hz
Power consumption 220W
Feed screw speed 185rpm
Motor protection Circuit breaker
Dimensions (HxWxD) (approx.) 386 x 166 x 310 mm
Weight (approx.) 3.2kg
Accessories Cutting plates, Kubbe attachment, Sausage attachment

3
3 Location of Controls and Components

4
4 Operating Instructions
4.1. How to Use ( Caution, Before use, ... How to Clean etc.)

5

6

7
5 Troubleshooting Guide
5.1. SYMPTOM : A.C. motor interrupted when feeding meat (overloaded).
5.2. SYMPTOM : Switch turned on, but A.C. motor failure to start.
5.3. SYMPTOM : A.C. motor running, but feed screw failure to turn.
5.4. SYMPTOM : A.C. motor running too noisy and meat grinding too slow.
5.5. SYMPTOM : A.C. motor running noise unusual.
5.6. SYMPTOM : Smell of burning from A.C. motor.
Causes Remedy
Too hard meat being fed. Take out the hard meat.
Too much meat being fed at once. Reduce the meat feed rate.
Used for too long continuously. Follow the specified operating time.
Circuit breaker activated. Switch off and on again to reset the breaker.
Causes Remedy
Power cord broken. Replace the power cord.
Lead wire terminal in poor contact. Repair or replace the lead wire terminal.
Switch in poor contact. Replace the switch.
Carbon brush worn out. Replace the carbon brush.
A.C. motor coil broken. Replace the A.C. motor.
Causes Remedy
Gears worn out. Replace the gears.
Gears damaged. Replace the gears.
Feed screw worn out. Replace the feed screw.
Feed screw damaged. Replace the feed screw.
Causes Remedy
Carbon brush worn out. Replace the carbon brush.
Gears worn out or damaged. Replace the gears.
Cutting blade or cutting plate worn out. Replace the cutting blade or cutting plate.
Causes Remedy
Foreign mater caught in gears. Take out the foreign matter.
Gears worn out or damaged. Replace the gears.
Causes Remedy
A.C. motor insulation degraded. Replace the A.C. motor.

8
6 Disassembly and Assembly Instructions
For assembly, refer to the Assembly Instructions, and perform the procedures in the opposite order of disassembly.
6.1. Rubber Cap, Connector U (lower)
1. Turn the locking knob counterclockwise to remove it.
2. Put a bladed screwdriver into each of the two holes at the
grinder bottom. Push down the housing cover claws to
detach the cover.
3. Lay the grinder with its left side down.
4. Remove the five pan head tapping screws and detach the
A.C. motor housing (left).
6.2. Disconnecting the power cord and switch
1. Lift the A.C. motor and disconnect the lead wire terminal.
2. Pull and disconnect the power cord terminal out of the switch.
3. Disconnect the lead wire terminal from the switch.
4. Remove the two switch lock screws and take out the switch.

9
6.3. Removing the gear case cover, gears and gear case.
1. Remove the two gear case cushions.
2. Remove the four lock screws and detach the gear case cover.
3. Take out the bearing B from inside the gear case cover.
• When reassembling, exactly fit the bearing B to gear case cover.
4. Take out the gears B, A and C in this order.
• The bearing B, washers and other parts come out together, attached by grease on the gears. Remember their positions and
assembling steps. Be also careful not to lose them.
5. Take out the bearing A, gear shaft and washers out of the gear case.
6. Remove the three gear case lock screws and detach the gear case from the motor.
• To reassemble the gear case, take the reverse steps.
Be very careful to put all the parts (gears, washers, bearings A and B, and gear shaft) together in the correct procedure into right
position and the right direction.
• Before placing the gears in position, apply grease on them.

10
6.4. Replacing the Carbon brush
1. Using a bladed screwdriver, widen the carbon holder.
2. Cut the carbon brush copper wire with nippers. Take out
the carbon brush.
3. Fit a new carbon brush in the carbon support plate.
4. Finally close the carbon holder.
(Replace both the carbon brushes at once.)

11
7 Wiring Connection Diagram
7.1. Schematic diagram
7.2. Basic Wiring diagram

12
8 Exploded View and Replacement Parts List
8.1. PARTS LOCATION

13
8.2. REPLACEMENT PARTS LIST
Notes:Important safety notice
• Components identified by mark have special characteristics important for safety.
• " When replacing any of these components use only manufacturer's specified parts."
MODEL No.MK-G1350PWTX
Safety Ref. No. Part No. Part Name & Description Pcs/Set Remarks
WTX
<PARTS LIST>
1 AME04-107-W Food pusher 1
2 AME03-107 Hopper 1
3 AME02-107 Grinder cap 1
4 AMM08C-180 Cutting plate A 1 Fine 3mm
5 AMM10C-180 Cutting plate C 1 Medium 5mm
6 AME05-121 Cutting plate F 1 Coarse 7mm
7 AMM12C-180 Cutting blade 1
8 AMM98C-180 Feed screw 1
9 AME01-1071 Grinder cap 1
10 AMY03Y121 Caution label 1
11 AMB19-107-W Motor housing (Right) 1
12 AJB05-108-H Foot 4
13 AMY10Y128 Rating plate 1
14 AMP96-1072 Power cord 1 220V-240V C-2P
15 AMB21-107-H Housing cover 1
16 AMM37A-180 Gear case cushion 2
17 AMM38A-491 Motor support rubber 2
18 AMB27-107 Gear case cover 1
19 AMM05B-180 Bearing B 1
20 AMM95B-270 Gear C 1
21 AMM18B-180 Adjustment washer B 1
22 AMM04B-180 Bearing A 1
23 AMM09B-270 Gear B 1
24 AMM26B-180 Gear shaft A 2
25 AMM08B-180 Gear A 1
26 AMM36B-180 Adjustment washer C 1
27 AMM40B-180 Cap washer 1
28 AMB26-107 Gear case 1
29 AMA08Y121-0S A.C. Motor 1 AC 220V-240V
30 AMJ16F-K70-2 Carbon brush 1 2pcs set
31 AMM31-121 Fan 1
32 AMP93-107 Lead wire A 1
33 AMN01Y107 Switch 1 AC 220V-240V
34 AMB91Y128-W0 Motor housing (Left) 1
35 AMM99A-302H1 Locking knob 1
36 AMM24C-270W Kubbe attachment B 1
37 AMM96C-270W Kubbe attachment A 1
38 AME96A107 Sausage attachment 1
<SMALL STANDARDIZED METAL PARTS>
A XTN4+20BFJ Screw 5
B XNG8BFJ Screw 1
C XWG5F14FJ Screw 3
D XYN5+C10FJ Screw 3
E SPN-8 Screw 1
F XTT4+16BFJ Screw 2
G XTN4+20BFJ Screw 4
<PACKING SPECIFICATIONS>
AMZ45Y12800S Outer carton 1
AMZ50Y128 Operating instructions 1
AMZ03-1072 Bottom plate 1
AMZ02-1072 Top plate 1
XZB15X70A015 Polybag for cord 1

14
8.3. PACKING INSTRUCTION