Panasonic MK-MG1560WTN User manual

© 2012 Panasonic Manufacturing Malaysia Berhad
(6100-K). Unauthorized copying and distribution is a
violation of law.
PMMA120717CE
Meat Grinder
Model No. MK-MG1560WTN
Destination : PGF
TABLE OF CONTENTS PAGE PAGE
1 PRECAUTIONS (Strictly follow these instruc-
tions.)----------------------------------------------------------------- 3
2 Specifications ----------------------------------------------------- 3
3 Schematic Diagram---------------------------------------------- 3
4 Basic Wiring Diagram------------------------------------------- 4
5 Disassembly and Assembly Instruction------------------ 5
5.1. Disassembly of Motor Housing------------------------- 5
5.2. Disassembly of Motor Set------------------------------- 6
5.3. Disassembly of Switch Knob --------------------------- 6
5.4. Disassembly of Gear Box ------------------------------- 7
6 Troubleshooting Guide -----------------------------------------8
6.1. SYMPTOM : A.C. motor interupted when
feeding meat (overloaded).------------------------------8
6.2. SYMPTOM : Switch turned on, but A.C. motor
failure to start.-----------------------------------------------8
6.3. SYMPTOM : A.C. motor running, but feed
screw failure to turn.---------------------------------------8
6.4. SYMPTOM : A.C. motor running too noisy and
meat grinding too slow.-----------------------------------8

2
6.5. SYMPTOM : A.C. motor running noise
unusual.-------------------------------------------------------8
6.6. SYMPTOM : Smell of burning from A.C.
motor.----------------------------------------------------------8
7 Exploded View and Replacement Parts List -------------9
7.1. Exploded View----------------------------------------------9
7.2. Packing Instruction---------------------------------------10
7.3. Replacement Parts List--------------------------------- 11

3
1 PRECAUTIONS (Strictly follow these instructions.)
CAUTION
Do not grind too hard meat. If the grinder gets stuck, do not force meat into it.
CAUTION
You may feel the feed screw vibrating during use. It is not a trouble. Do not over tighten the locking knob.
CAUTION
Keep in mind that some parts of the grinder cannot be washed in a dishwasher.
CAUTION
This meat grinder is for household use only.
2 Specifications
3 Schematic Diagram
Destination PGF
Model MK-MG1560WTN
Power Source AC220V~240V~50/60Hz
Motor Power 240W~260W
Protective Device Circuit Breaker AC250 V 1.6 A (4.5s - 7.0s)
Type of Switch Rotary Switch
Power Cord Length 0.9 m
Hopper Material Aluminium
Dimensions (WXDXH) 155mm X 276mm X 214mm
Weight (approx.) 3.8kg
Meat Grinding
(Middle Gring Cutter) Beef 1200 g/min, Mutton 800 g/min
Cutter Type Rough Grind 0 (Hole 7 x 16 pcs),
Middle Grind 0 (Hole 5 x 30 pcs),
Fine Grind 0 (Hole 3 x 78 pcs)
Kubbe Attachments Yes

4
4 Basic Wiring Diagram
Motor housing
Switch
Red
Fan
Brown
Blue
Power cord Condenser
Gear case
A.C. Motor

5
5 Disassembly and Assembly Instruction
5.1. Disassembly of Motor Housing
Step 1 Remove 4 screws.
Step 2 Remove Locking Knob.
Step 3 Open Motor Housing.

6
5.2. Disassembly of Motor Set
Step 1 Remove 2 screws.
Step 2 Pull up Gear box.
Step 3 Detach Connector from Motor Unit.
5.3. Disassembly of Switch Knob
Step 1 Remove Switch Knob.

7
5.4. Disassembly of Gear Box
Step 1 Remove 4 screws.
Step 2 Release 4 Rubber Holders.
Step 3 Remove Top Gear Cover.
Step 4 Remove Gears
Caution: Wear Glove when take out Gears
Step 5 Remove 3 Screws.
Step 6 Remove Bottom Gear Cover.
Caution: During assembling, ensure that all Gears have
been Grease.

8
6 Troubleshooting Guide
6.1. SYMPTOM : A.C. motor interupted when feeding meat (overloaded).
6.2. SYMPTOM : Switch turned on, but A.C. motor failure to start.
6.3. SYMPTOM : A.C. motor running, but feed screw failure to turn.
6.4. SYMPTOM : A.C. motor running too noisy and meat grinding too slow.
6.5. SYMPTOM : A.C. motor running noise unusual.
6.6. SYMPTOM : Smell of burning from A.C. motor.
Causes Remedy
Too hard meat being fed. Take out the hard meat.
Too much meat being fed at once. Reduce the meat feed rate.
Used for too long continuously. Follow the specified operating time.
Circuit breaker activated. Switch off and on again to reset the breaker.
Causes Remedy
Power cord broken. Replace the power cord.
Lead wire terminal in poor contact. Repair or replace the lead wire terminal.
Switch in poor contact. Replace the switch.
Carbon brush worn out. Replace the carbon brush.
A.C. motor coil broken. Replace the A.C. motor.
Causes Remedy
Gears worn out. Replace the gears.
Gears damaged. Replace the gears.
Feed screw worn out. Replace the feed screw.
Feed screw damaged. Replace the feed screw.
Causes Remedy
Carbon brush worn out. Replace the carbon brush.
Gears worn out or damaged. Replace the gears.
Cutting blade or cutting plate worn out. Replace the cutting blade or cutting plate.
Causes Remedy
Foreign matter caught in gears. Take out the foreign matter.
Gears worn out or damaged. Replace the gears.
Causes Remedy
A.C. motor insulation degraded. Replace the A.C. motor.

9
7 Exploded View and Replacement Parts List
7.1. Exploded View
faiz
B10 (C2)
B1
B2
B3
B4
B5
B7
B6
B8
B9
B33
B11
B11
B11
B11
B12
B13
B14
B15
B16
B17
B19
B20
B21 B22
B23
B24
B25
B25
B31
B26
3
3
1
1
1
1
3
2
B27
5
4B28
B32
B29 B30
B20
3
4
4
B34
B18
B35
B3
6

10
7.2. Packing Instruction
Housing unit
Cutting Plate
Food Pusher
P4
Hopper
Grinder cap
Kubbe attachment A
Power Cord
Grinder head
Panaso nic
MK-MG150 0
Kubbe attachment B
P1
MZ02-133
TO P
P2
P3

11
7.3. Replacement Parts List
MMH1207
Safety Ref.
No.
Part No. Part Name & Description Qty Remarks
B1 AME04-1072W0 PLUNGER 1
B2 AME03-133-CA HOPPER 1 ALUMINIUM
B3 AME01-121 SCREW BODY 1
B4 AM98C18000 SCREW (U) 1
B5 AM12C18000 ROTATING CUTTER 1
B6 AM08C18100 CUTTER A 1
B7 AM10C18100 CUTTER C 1
B8 AME02-121 BODY COVER 1
B9 AMN99-133-W4 ROTARY KNOB UNIT 1
B10 AMP96Y133-WZ CORD UNIT 1 C2 PLUG
B11 AMB34-133 GEAR CUSHION RUBBER 4
B12 AMB26-1103 GEAR CASE 1
B13 AMB89-1102 GEAR CASE COVER UNIT 1
B14 AM04B18100 OILLESS BEARING A 1
B15 AM18B18000 WASHER B 1
B16 AMH99-110 C GEAR UNIT 1
B17 AM05B18100 OILLESS BEARING B 1
B18 AMA32-121 COMPLETE SCREW BODY 1
B19 AMH02-110 B GEAR 1
B20 AMH61-110 A GEAR SHAFT 2
B21 AMH97-110 A GEAR UNIT 1
B22 M06B18000 OILLESS BEARING C 1
B23 AM36B18100 WASHER C 1
B24 AMH53-133 WASHER D 1
B25 AMB35-133 MOTOR CUSHION RUBBER 2
B26 AMB91Y136-W4 BODY LEFT UNIT 1
B27 AMB21-133 FRONT PLATE 1
B28 ATXM131Y MOTOR 1
B29 AM24C27300 KUBBE COVER 1
B30 AM96C27300 KUBBE UNIT 1
B31 AMB19-133-W4 BODY RIGHT 1
B32 AMM31-1101K0 FAN 1
B33 AMN98Y133-W4 REVERSE SWITCH ASSY 1
B34 AMA20-121 FIXED CUTTER COMPLETE 1
B35 AM24Q27300 KUBBE COMPLETE 1
B36 ASPN-9012 PUSH NUT 1
1 XTN4+20BFJ SCREW 4
2 AMB85-133-W4 FIX KNOB UNIT 1
3 XTN4+20BFJ PLUS TAPPING SCREW 4
4 XYN4+20BFJ SCREW WITH SPRING AND ROUND
WASHER
3
5 XNG8BFJ HEXAGONAL NUT 1
PACKING LIST
P1 AMZ50Y133 OPERATING INSTRUCTION 1
P2 AMZ02-133 TOP CUSHION 1
P3 AMZ03-133 BOTTOM CUSHION 1
P4 AMZ01Y136 CARTON BOX 1