Panasonic ET-LAE200C User manual

Model No. ET-LAE200C
ENGLISH
Operating Instructions
Replacement lamp unit Commercial Use
Thank you for purchasing this Panasonic product.
■Before using this product, please read the instructions carefully, and
save this manual for future use.
■Beforeusingthisproduct,besuretoread[Readthisrst!](PageE-2).
TQZJ625-1

Read this rst! Always follow these precautions
CAUTION:
Do not use the old lamp unit.
If used it could cause lamp explosion.
If the lamp has broken, ventilate the room immediately. Do not
touch or bring your face close to the broken pieces.
Failure to observe this will cause the user to absorb the gas which was released
whenthelampbrokeandwhichcontainsnearlythesameamountofmercuryasuo-
rescent lamps, and the broken pieces will cause injury.
•If you believe that you have absorbed the gas or that the gas has got into your
eyes or mouth, seek medical advice immediately.
•Ask your dealer about replacing the lamp unit and check the inside of the projector.
E-2
WARNING:
TURNOFFTHEUVLAMPBEFOREOPENINGTHELAMPCOVER.
WARNING:
Do not disassemble the lamp unit.
If the lamp breaks, it could cause injury.
Lamp replacement
The lamp has high internal pressure. If improperly handled, an explosion and severe
injury or accidents will result.
•The lamp can easily explode if struck against hard objects or dropped.
•Before replacing the lamp, be sure to disconnect the power plug from the wall out-
let.Electricshocksorexplosionscanresultifthisisnotdone.
•When replacing the lamp, turn the power off and allow it to cool for at least 1 hour
before handling it otherwise it can cause burns.
Notes on replacing the lamp unit
•The light source lamp is a glass component. If it is hit on a hard object or dropped,
breakage may occur. Be careful when handling a light source lamp.
•A Phillips screwdriver is necessary when replacing the lamp unit. Hold the screw-
driverrmly.
•Gripthehandlewhenyouremovethelampunit.Somepartsofthelampunitare
sharpened and may cause injury.
•Thelampcontainsmercury.Contactthelocalgovernmentofceordistributorforthe
correct disposal of the old lamp unit.
•If you continue to use a lamp after the replacement time, the lamp may break.
•Do not disassemble the lamp unit.
•When replacing the lamp because it has stopped illuminating, there is a possibility
that the lamp may be broken. If replacing the lamp of a projector which has been
installed on the ceiling, you should always assume that the lamp is broken, and you
should stand to the side of the lamp cover, not underneath it. Remove the lamp cover
gently.Smallpiecesofglassmayfalloutwhenthelampcoverisopened.Ifpiecesof
glass get into your eyes or mouth, seek medical advice immediately.

ENGLISH
Replacing the Lamp unit
CAUTION:
zWhen the projector is mounted on a ceiling, do not work with your face close to the
projector.
zAttach the lamp unit and the lamp cover securely.
zWhenyouexperiencedifcultyininstallingthelamp,removeitandtryagain.Ifyou
use force to install the lamp, the connector may be damaged.
zDo not use other than designated lamp units.
zDo not lossen other than designated screws.
JReplacement procedure
1) Turn off the Power by following the
procedure in "Turning off the projector".
Unplug the AC power cord. Wait at least
1 hour and make sure the lamp unit and
surroundings are cool.
2) Use a Phillips screwdriver to loosen the
lamp cover xing screw and open the
lamp cover.
zOpen the lamp cover, slide the lamp cover in
the direction of the arow shown in the right
picture and let the projector stand on the
side at the same time.
3) Use a Phillips screwdriver to loosen the
three lamp unit xing screws until the
screws turn freely. Hold the used lamp
unit by its handles, and pull it gently
from the projector.
4) Insert the new lamp unit in correct
direction. Tighten the three lamp unit
xing screws securely with a Phillips
screwdriver.
5) Close the lamp cover, and tighten the
lamp cover xing screw securely with a
Phillips screwdriver.
zClosethelampcoverbypushingitslowly
opposite to the direction of the arrow.
E-3
Lampcover
xingscrew
Lampcover
Lampunitxingscrews
Handles
Note
zWhenyoureplacethenewlampunit(ET-
LAE200C),theprojectorresetsthetotalusagetime
of the lamp unit automatically.
LAMP NO. : ET-LAE200C

■Information on Disposal in other Countries outside the
European Union
■Instruction of Environmental Protection Period Mark
TheEnvironmentallyFriendlyUsePeriodfortheprojectionlamp
used in this product is 5 years.
ThissymbolisonlyvalidintheEuropeanUnion.
If you wish to discard this product, please contact your local
authorities or dealer and ask for the correct method of disposal.
■Name and quantity of hazardous substances contained in
the product
Part Name Hazardous Substances
Pb Hg Cd Cr(VI) PBB PBDE
Projection lamp × × ○ ○ ○ ○
Mechanical parts ×○ ○ ○ ○ ○
ThistableispreparedinaccordancewiththeprovisionsofSJ/T11364.
○
: Indicates that this hazardous substance contained in all of the
homogeneousmaterialsforthispartisbelowthelimitrequirementinGB/T
26572.
×
: Indicates that this hazardous substance contained in at least one of the
homogeneous materials used for this part is above the limit requirement in
GB/T26572.
松下电器 （中国）有限公司
北京市朝阳区景华南街 5 号远洋光华中心 C 座3 层、6 层
网站：https://panasonic.cn
原产地 ：中国
发行 ：2022 年6月
© 松下互联株式会社 2022 版权所有
TI0612JG2062 -PT
PrintedinChina