Panasonic DBS 824 User manual

Section 320
DBS 824 to DBS
Interconnection
Panasonic
a
(Applies to CPC-AII/B Version 9.2
and CPC-EX Version 2.3)
Version 2.3/9.2
Revised April 2000

The contents of this manual are subject to change without notice and do not constitute a
commitment on the part of Panasonic Telecommunication Systems Company (PTSC). Every
effort has been made to ensure the accuracy of this document. However, due to ongoing product
improvements and revisions, Panasonic cannot guarantee the accuracy of printed material after
the date of publication nor can it accept responsibility for errors or omissions. Panasonic will
update and revise this document as needed.
The software and hardware described in this document may be used or copied only in accordance
with the terms of the license pertaining to said software or hardware.
This document may be reproduced either electronically or in print as needed by certified dealers
and technicians of DBS products. However, the information contained in this document must not
be altered, copied, or changed in any way that misrepresents the installation, operation, or other
function or feature of the DBS product or Panasonic. Panasonic assumes no liability for any
alteration or misrepresentation of information contain herein.
Copyright 1995 by Panasonic Telecommunication Systems Company
Revised April 2000
All rights reserved.
Warning: This service information is designed for experienced repair techni-
cians only and is not designed for use by the general public. It does not contain
warnings or cautions to advise non-technical individuals of potential dangers in
attempting to service a product. Products powered by electricity should be ser-
viced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this service information
by anyone else could result in serious injury or death.

DBS-2.3/9.2-320 DBS Manual - Revised April 2000 iii
Table of Contents
Introduction ..................................................................................................................................1
Guidelines ....................................................................................................................................1
Installation ...................................................................................................................................6

iv DBS Manual - Revised April 2000 DBS-2.3/9.2-320

Section 320 - DBS 824 to DBS Interconnection Supplement Introduction
DBS-2.3/9.2-320 DBS Manual - Revised April 2000 1
Introduction
A DBS 824 cabinet can be connected to a DBS 40, 72 or 96 cabinet in order
to increase capacity. This document includes connection procedures, as well
as capacities for these two-cabinet systems.
This chapter covers the following topics:
Guidelines
• The DBS is always the master and the DBS 824 is always the slave.
• The DBS requires the CPC-B version 6.1 or later and the SCC-B.
• Since the CPC-B card is the controlling card, follow the programming
instructions in the DBS Section 400 and the feature operations in DBS
Section 700.
• Since both DBS and DBS 824 items are used, refer to the installation
instructions in both the DBS Section 300 and the DBS 824 Section 300.
• If an MFR card is used, it must be installed in the DBS 824 CPC slot. The
MFRU card cannot be used.
• T1 can only be used with the DBS 96 in a DBS 96 to DBS 824 Dual
Cabinet System. No other combination supports T1.
• The SMDR, Bus Monitor, etc. are provided from the DBS cabinet.
• The DBS 824 cabinet only supports loop start trunks.
• The DBS 824 cabinet does not support AECs. An SLT-A or OPX adaptor
must be used to connect analog devices.
• Figures 1 through 3 shows slot usage for two-cabinet combinations.
• Table 2 on page 3 shows possible two cabinet configurations and
maximums.
• The DBS 824 may have most options connected including Caller ID,
OPX, VAU. Exceptions or considerations include the following:
Topic Page
Guidelines 1
Installation 6

Guidelines Section 320 - DBS 824 to DBS Interconnection Supplement
2 DBS Manual - Revised April 2000 DBS-2.3/9.2-320
Table 1. DBS 824 Dual Cabinet Feature Considerations
N/A = Not Available
Feature CPC-B
6.1 CPC-B 7.0 Notes:
Auto Repeat Dial N/A N/A
Auto Redial N/A Available
Personal Speed Dials 10 PSDs/
Extension 10 PSDs/ Extension
System Speed Dials 90 SSDs 200 SSDs
2-Port OPL N/A N/A
2-Port MFR N/A N/A
Night 2 Mode N/A Available
SMDR/Bus Monitor See Note. See Note. Uses DBS CN6 SMDR/Bus Monitor
instead of DBS 824 Connector.
External Ringer Audio
Separation N/A N/A Uses DBS EPA Connector for both External Ringer and Paging
Internal Hold Tone N/A Available
Full Call Forwarding
Outside N/A Available CPC 6.1 supports call forwarding an internal call outside (723)
Battery Alarm N/A N/A
Extension Port Based
Door Phone Adaptor N/A Available
4-Port Single Line
Telephone Adaptor N/A Available

Section 320 - DBS 824 to DBS Interconnection Supplement Guidelines
DBS-2.3/9.2-320 DBS Manual - Revised April 2000 3
Table 2. Trunk and extension port maximums for double-cabinet systems
Figure 1. Slot usage for two-cabinet systems, DBS 40 + DBS 824
System Combinations Trunk Extension Expansion Ports
Master Slave Ports Ports (Trunk lines or extensions)
DBS 40 DBS 824 16 48 0 (See Note 1.)
DBS 72 DBS 824 24 72 0 (See Note 1.)
DBS 96 DBS 824 32 88 8 (See Note 2.)
Notes:
1. When a DBS 40 or DBS 72 is connected to a DBS 824, the expansion ports cannot be used.
2. The DBS 96 cabinet must be used for expansion ports.
DBS 824 (Slave)
DBS 40 (Master)
Built-In TRK Ports 9-12
Built-In EXT Ports 25-32
208 208 CPC AUX
TRK 13-14 EXT 33-40 TRK 15-16 EXT 41-48 MFR CBL-S
TRK1 EC1 EC2 EC3 EC/
TRK SCC CPC AUX1 AUX2
TRK 1-8 EXT 1-8 EXT 9-16 EXT 17-24 N/A SCC-B CPC-B API CBL-M

Guidelines Section 320 - DBS 824 to DBS Interconnection Supplement
4 DBS Manual - Revised April 2000 DBS-2.3/9.2-320
Figure 2. Slot usage for two-cabinet systems, DBS 72 + DBS 824
DBS 824 (Slave)
DBS 72 (Master)
Built-In TRK Ports 17-20
Built-In EXT Ports 49-56
208 208 CPC AUX
TRK 21-22 EXT 57-64 TRK 23-24 EXT 65-72 MFR CBL-S
TRK
1TRK 2TRK 3EC1 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/ TRK SCC CPC AUX 1AUX 2
TRK 1-8 TRK 9-16 N/A EXT 1-8 EXT 9-16 EXT 17-24 EXT 25-32 EXT 33-40 EXT 41-48 N/A N/A N/A SCC-B CPC-B API CBL-M

Section 320 - DBS 824 to DBS Interconnection Supplement Guidelines
DBS-2.3/9.2-320 DBS Manual - Revised April 2000 5
Figure 3. Slot usage for two-cabinet systems, DBS 96 + DBS 824
DBS 824 (Slave)
DBS 96 (Master)
Notes:
*See “T1 Interface” in Chapter 4 of the DBS Installation Manual Section 300 for EC/TRK
port numbers for a T1 installed in the DBS 96.
Built-In TRK Ports 33-36
Built-In EXT Ports 73-80
208 208 CPC AUX
TRK 37-38 EXT 81-88 TRK 39-40 EXT 89-96 MFR CBL-S
TRK
1TRK 2TRK 3EC1 EC2 EC3 EC4 EC5 EC6 EC7 EC8 EC/ TRK SCC CPC AUX 1AUX 2
TRK 1-8 TRK 9-16 TRK 17-24 EXT 1-8 EXT 9-16 EXT 17-24 EXT 25-32 EXT 33-40 EXT 41-48 EXT 49-56 EXT 57-64 TRK 25-32 or EXT 65-72 SCC-B CPC-B API CBL-M

Installation Section 320 - DBS 824 to DBS Interconnection Supplement
6 DBS Manual - Revised April 2000 DBS-2.3/9.2-320
Installation
1. Set SW1 on the CBL-M card according to the following table.
Table 3. CBL-M switch settings
2. Install the circuit cards according to the layouts shown in the Figures 1
through 3.
Note: The port numbers for each slot are fixed.
3. Using the cables provided, connect the CBL-M card in the master cabinet
to the CBL-S card installed in the slave cabinet. The cables should be
connected with the green ground cables located at the CBL-M card.
Note: The EMI filter must be installed as close to the cabinet as possible,
as shown in Figure 4 on page 7.
4. Connect the green ground lead on each of the DBS cables to a side frame
screw on the DBS cabinet.
System
Combinations Switch Settings
MasterSlave 12345678
DBS 40 DBS 824 ON ON ON ON ON ON OFF ON
DBS 72 DBS 824 ON OFF ON ON ON ON OFF OFF
DBS 96 DBS 824 OFF ON OFF ON ON OFF OFF OFF