Panasonic KX-DTU100 User manual

Quick Reference Guide
Digital Communication Terminal
Model No. KX-DTU100
Thank you for purchasing a Digital Communication Terminal. Please read this
manual carefully before using this product and save this manual for future use.
For more details, please refer to the manuals of the PBX.
This unit is connected to the PBX as a Digital Propriety Telephone (DPT). Refer to
the DPT settings description in your PBX manual.
Manuals and supporting information are provided on the Panasonic Web site at:
https://panasonic.net/cns/pcc/support/pbx/
Note
• In this manual, the suffix of each model number is omitted unless necessary.
• The illustrations may differ from the appearance of the actual product.

1 Important Information
WARNING
Disconnect the telephone line cord from this product if this product emits smoke,
an abnormal smell, or makes unusual noise. These conditions can cause fire or
electric shock. Confirm that smoke has stopped and contact an authorized
service center.
For users in Canada
• This Class B digital apparatus complies with Canadian ICES-003.
• This product meets the applicable Innovation, Science and Economic
Development Canada technical specifications.
For users in the United states
FCC and Other Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.
1 Important Information
2

For users in the European Union
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying
documents mean that used electrical and electronic products and
batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and
batteries, please take them to applicable collection points in
accordance with your national legislation.
By disposing of them correctly, you will help to save valuable
resources and prevent any potential negative effects on human
health and the environment.
For more information about collection and recycling, please
contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in
accordance with national legislation.
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical
symbol. In this case it complies with the requirement set by the
Directive for the chemical involved.
1 Important Information
3

For information of Compliance with EU relevant Regulatory
Directives, Contact to Authorized Representative:
Panasonic Testing Center
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
For Users in the United Kingdom
• This unit is designed to be installed under controlled conditions of ambient
temperature and a relative humidity.
• Avoid installing the unit in damp or humid environments, such as bathrooms or
swimming pools.
1 Important Information
4

2 Accessory Information
Included Accessories
Stand (1) Telephone Line Cord (1)*1
Screws for wall mounting (2)
*1 The unit includes one cord. Consult your dealer if additional cords are
needed.
2 Accessory Information
5

3 Location of Controls
A
B
C
D
EFGH
J
I
K
① Call Button (Flexible Button 1)
Used to perform calls to caregivers.
② One Touch Button 1 (Flexible Button 3)
③ One Touch Button 2 (Flexible Button 4)
④ One Touch Button 3 (Flexible Button 5)
Perform the functions assigned to the respective Flexible Buttons as One
Touch Buttons.
⑤ Microphone
Used for hands-free talking.
⑥ Cancel Button (Flexible Button 2)
Stops the features that are currently running.
⑦ Volume Button
Used to adjust the volume.
⑧ Pin Jack
Used Connect a Push Switch cable plug. It supports only 6.35 mm (1/4 in)
plugs.
3 Location of Controls
6

⑨ Pin Jack Cover
Used to cover the Pin Jack hole when the Pin Jack is not in use.
⑩ Speaker
Used for hands-free talking and for listening to recorded messages.
⑪ Status LED
Used to confirm the status of the unit. When the unit is in use, the Status LED
turns off.
3 Location of Controls
7

4 Feature Operations
Before operating the unit
Before operating this unit, initial setup of the PBX is necessary.
For more information about how to setup the PBX settings, please refer to the
PBX manuals or contact your dealer.
Manuals and support information are provided on the Panasonic Web site at:
https://panasonic.net/cns/pcc/support/pbx/
4.1 Making a call
Pressing the Call Button ( )
This operation will make a call. While the call is being made, a ringback tone is
heard from the speaker. Simultaneously, the Call LED will begin to blink, and the
Status LED will turn off. When the call is being made, pressing any One Touch
Button will have no effect.
Pressing the Push Switch (optional)
This operation performs the same function as pressing the Call Button.
When making a call with the Call Button or during a conversation, the call or
conversation will be terminated, and it will make another call.
Pulling out the Push Switch (optional) cable plug from the Pin
Jack
This operation performs the same function as pressing the Call Button.
When making a call with the Call Button or during a conversation, the call or
conversation will be terminated, and it will make another call.
Pulling the External Pull Switch (optional) Cord
This operation performs the same function as pressing the Call Button.
When making a call with the Call Button or during a conversation, the call or
conversation will be terminated, and it will make another call.
Pressing the One Touch Button
If each One Touch Button is assigned as a One-touch Dialing setting and a
destination phone number is registered, you can make a phone call to that phone
number just by pressing the button.
4 Feature Operations
8

For example, it is convenient to register a telephone number of relevant peoples
or facilities. (Home, caregivers, family members, etc.)
Note
In order to operate in this way, proper PBX settings are needed.
However depending on the PBX settings, different operation is also possible.
For details, consult your system administrator.
4.2 Playback messages
Pressing the One Touch Button
If each One Touch Button is assigned to One-touch Dialing and other settings are
set appropriately, you can hear recorded messages just by pressing the button.
For example, it is convenient for listening to information and announcements of
daily events, like menu information, facility information and other things.
Note
In order to operate in this way, proper PBX settings are needed.
However depending on the PBX settings, different operation is also possible.
For details, consult your system administrator.
4.3 Adjusting the Call Volume
Pressing the Volume Button ( )
If you press the Volume Up button ( ) during a conversation or playback
messages, the volume will increase, and if you press the Volume Down button
( ) during a conversation or playback messages, the volume will decrease. If
you press and hold either button, the volume adjustment continues. The volume
is adjustable in four levels.
4.4 Terminate currently running feature
Pressing the Cancel Button
To terminate a conversation, message playback or call, press the Cancel Button
().
The Call LED and the Status LED will change to solid light, and the unit will enter
standby status.
4.2 Playback messages
9

Disconnected by the Called Party
If the called party hangs up the phone, the conversation will be terminated and
the unit will enter standby status without pressing the Cancel Button. *1
*1 A reorder tone may be heard from the speaker.
Press the Cancel Button at that time, then the reorder tone will stop and the
unit will enter standby status.
Note
In order to operate in this way, proper PBX settings are needed.
However depending on the PBX settings, different operation is also possible.
For details, consult your system administrator.
4.4 Terminate currently running feature
10

5 LED Indications
The status of the unit is indicated by the condition of the two LEDs shown in the
table below:
A B
Status ① Status LED
（Green)
② Call Button LED
（White)
Out of service (OUS) *1 OFF OFF
In Service (INS) *2 ON ON
In Operating *3 ON ⇒ OFF ON ⇒ Blink (Slow)
Cancel Button is
pressed.*4 OFF ⇒ ON Blink (Slow) ⇒ ON
One Touch Button is
pressed. *5 ON ⇒ OFF ON
*1 The power of the unit is off, the PBX is not connected or an unsupported
PBX is connected.
*2 The unit is ready to use. (Standby status)
*3 On calling or in conversation.
*4 The unit finishes the operation and returns to standby status.
*5 One Touch Button is assigned to three Flexible Buttons.
5 LED Indications
11

6 Installation and Setup
Note
• Panasonic assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with
this documentation.
Attaching the Stand
Main unit Stand
A
B
① Holes for the hook mounting (4 points)
② Stand hooks (4 points)
1. Insert the catches of the unit into the hooks located in the stand.
2. Gently slide down the unit until it locks into the stand.
3. Then confirm the unit will be mounted firmly and the right place on the stand.
6 Installation and Setup
12

Removing the Stand
1. Gently slide up the unit until
the stand hooks will be
released from the holes of
the unit with both hands as
shown.
2. Remove the unit from the
stand carefully.
6 Installation and Setup
13

Connections
Basic Connection for Wall Mounting
TO TELTO PABX
TO MAIN UNIT
Use clamps
Use two clamps
Connect to:
a pull switch unit
Connect to:
a digital proprietary telephone
Connect to a PBX.
The telephone line cord
Digital XDP connection
6 Installation and Setup
14

Note
When this unit will be installed on a telephone wall plate or a gang box, using any
clamps are subject to change for smooth running of the cables.
Connection for the Stand Installation
1. Connect the telephone line cords and the Pull switch cable as shown below
Not use clamps Use upper clamp only
6 Installation and Setup
15

2. Attach the stand to the unit. Then hook the telephone line cords into the
clamps as shown below.
6 Installation and Setup
16

Connecting a Push Switch unit
1. Before using, remove the Pin
Jack Cover.
Note
To avoid accidental ingestion,
place it out of reach of
children.
When the Push Switch cable
plug is not connected to the
Pin Jack, make sure the Pin
Jack is covered by the Pin
Jack Cover for protection.
Pin Jack Cover
2. Insert the Push Switch Unit
plug into the Pin Jack.
Use a 6.35 mm (1/4 in) plug.
3. Check that the plug is fully
inserted all the way.
6 Installation and Setup
17

Connecting a Pull Switch unit
1. Use a flathead screwdriver to press and hold open the button below the
terminal, and insert a pair of wire coming from the Pull Switch into the
terminal.
Cable Length:
Up to 50 m (164 ft)
6 mm
(15/64 in)
Stripped end of the wire
2 pin terminal
(Non polar)
Pull Switch unit
(In a bathroom
or a next room)
6 Installation and Setup
18

Note
•When connecting a Push Switch unit
Technical information about the Push Switch units that have been tested with
this unit is provided on the Panasonic Web site at:
https://panasonic.net/cns/pcc/support/pbx/
•When connecting a Pull Switch unit
A cable used to connect a pull switch to the 2 pin connector must be less than
50 m (164 ft) in length. We recommend to use a pair of wire cable with diameter
of AWG 22 (Ф0.65 mm).
Strip off the wire cover so that about 6 mm (15/64 in) of the wire is exposed.
•When connecting telephone line cords
Ensure the cords are inserted in the grooves, and are clamped to prevent
damage to the connectors.
6 Installation and Setup
19

7 Wall Mounting
1. Connect the cables to the unit and run the cables as shown in the illustration
below.
2. Drive the screws into the wall either 83 mm (3 1/4 in) or 100 mm (3 15/16 in)
apart, and mount the unit on the wall.
Example
2
1
The Pull Switch cable
The telephone
line cord
Washer
Drive the screw
to this point.
83 mm
(3 1/4in) 100 mm
(3 15/16 in)
7 Wall Mounting
20