ParaBody Serious Steel 827104 User manual

Serious Steel
827104 LAT MACHINE
ASSEMBLYINSTRUCTIONS
Part # 6760301 Revision: 1/18/99

]IMPORTANT NOTES]
WELCOMETO THE WORLDOF
Please note:
*Thankyou for purchasing the Parabody827104LATMACHINE.Please read these in~struc-
t-ions thoroughlyand keepthemfor future reference. This productmustbe assembledon a
fiat, level surfaceto assureits properfunction.
Werecommendcleaning your product (pads and flame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchasedfromyour Parabodycustomersel-vc.ice representative
at [phone].
Thereis a risk assumedbyindividuals whouse this type of equipment.Tomininaizerisk, please
followthese rules:
1. Inspect equipmentdaily. Tightenall loose connectionsandreplace wornparts irmnediately.
Failureto doso mayresult in seriousinjury.
2. Donot allow minorsor children to play on or aroundthis equipment.
3. Exercisewithcare to avoidinjury.
4. If unsureof properuseof equipment,call yourlocal Parabodydistributor or call the
Parabodycustomerservice departmentat [phone].
5. Consulta physician before beginningany exercise program.
I Tools Required for Assembly
* 3/4" wrench
* 9/16" wrench
* Ratchetwith 3/4" and9/16" sockets
*Adjustable wrench
* Tape measure
I Bolt LengthRuler I
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER:
II/I//i/~
BOLTLENGTH
I1/2 l 1/2 I 1/2 I 112 I 1/2 I 1/2 I
6
34 [ I I I
0 1 I I I I

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2O
PART# DESCRIP’rION
6759103 BASE
6758903 FRONTUPRIGHT
6760003 REAR UPRIGHT
6759603 TOP BOOM
6759802 CARRIAGE
6759302 ROLLERPADSUPPORT
6275302 LAT BAR
6274402 LOW ROWBAR
6489902 1/4 X2X7-1/4" PLATE
6664802 SEAT PAD
6194601 ROIJ ]z~PAD
6576201 CABLE
3103102 1 X8" GRIP
3116201 3-1/2"PUIJ JEY
3116101 4-1/2"PUI J~EY
6177001 2-1/2 X 5-1/2" NON-SKIDSTRIP
6405201 2" SQ. ENDCAP
6467001 2" SQ COVERCAP
6692601 3 X2" ENDCAP
3119301 2-1/2" ROUNDENDCAP
PARTS
1
1
1
1
1
1
1
1
2
1
2
2
4
5
2
2
2
2
3
2
LIST
I~/
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
PART# DESCRItVHON
6590801- 3 X 2" INSEI~["GUIDE "
6387901 Y’ VINYL
3116001 1-1/4" SQ. RUBBERBUMPER
3102501 3/8" WA~;HER
3102802 3/8" LOC~
3102502 1/2" WASHER
3102801 1/2" LOC~
3102902 3/8X2-1/4’ ~LT
3/8X 2-3/4" BOLT
3102922
3102906
3102910
3102917
6480301
3/8X4"t )LT
1/2X3"t )LT
1/2X4" t )LT
3/8" FLAN~5~PACER
6412001 SPRINGPINA;EIVIBLY
3103801 5/16" SNAPLINK
3108102
6075906
6140701
1/4" QUICKDIS C()NNECI"LIN~
12 LINK{2HAIN
1Xl" 151 DE
9 I
3 I
4 I
1ol
3

FIGURE
,1/2 X3"
STEP1:
¯ Attachtwo 2" SQ. COVERCAPS(18) onto the ends ofthe REARUPRIGHT(3) as shownin FIGUKE
¯ Insert two 3 X 2" ENDCAPS(19) imo the ends of the BASE(1) and REARUPRIGHT(3) as shownin FI~URE
¯ Insert two 2-1/2" ROUNDENDCAP(20) into the tube on the BASEFRAME(1) as shown in FIGURE
¯LOOSELYassemble the REARUPRIGHT(3) to the BASE(1) using two 1/2 X 3" BOLTS(32), two ’~ WASHERS (27), and
two 1/2" LOCKNUTS(28). See FIGURE
[ 1/2 I 1/2 [ 1/2 I 1/2 I 1/2 [ 1/2 I
6

FIGURE 2
STEP2:
¯ Attach eight 1 X1" GLIDES(39) to the ends the CARRIAGE(5) as shownin FIGURE2 using the following st~ps:
¯Thoroughlyclean all surfaces wherethe 1 X1" GLIDES(39) are to be attached.
¯Removethe 1 X1" GLIDES(39) fromthe paperbackingand firmly applythemto all shownsurfaces.
¯ SECURELYattach one 1-1/4" SQ. RUBBERBUMPER(24) to the CARRIAGE(5) as shown in FIGURE
FIGURE 3
STEP3:
¯Insert two 3 X 2" GUIDES(21) into the ends of the ROLLERPADSUPPORT(6) as shownin FIGURE
¯Assemble two ROLLERPADS(11) to the ROLLERPADSUPPORT(6) using t~vo STARLOCKCOLLAteS(23).
¯SECURELYassemble one SPRINGPIN ASSEMBLY(35) to the spring pin barrel on the ROLLERP,~d:) SUPPOP~T(6).
FIGURE3, 5

FIGURE 4
STEP 4:
¯ Insert two 2" SQ. ENDCAPS(17) imo the FRONTUPRIGHT(3) as shownin FIGURE
LOOSELYassemble the FRONTUPRIGHT(3) to the BASE(1) using two 1/2 X 4" BOLTS(32) and two 1/2" LOCK
(28). See FIGURE
1/2 ] 1/2 I 1/2 I 1/2 I 1/2 I 1/2 I
6
2 I I I I
6

FIGURE5
;TEP 5:
CAREFULLYslide the ROLLERPADSUPPORT(6) over into the FRONTUPRIGHT(2) and engage the SPRINGPIN
one of the adjustmentholes. See FIGURE5.
CAREFULLYslide the CARRIAGE(5) over into the REARUPRIGHT(3) as showrt in FIGURE
7

’1/2 X3"
FIGURE 6 3/8 X2-3/4
STEP6:
¯LOOSELYassemble the TOPBOOM(4) to the FRONTUPRIGHT(2) using one 1/2 X3" BOLT(32), two 1/2" WASHERS
and one 1/2" LOCKNUT(28). See FIGURE
¯LOOSELYassemble the TOPBOOM(4) to the REARUPRIGHT(3) using two 1/2 X4" BOLTS(33), two 1/2" WASHERS
and one 1/2" LOCKNUT(28). See FIGURE6. (NOTE:IMPORTANT!Makesure bolts in TOPBOOMare facing shown
in FIGURE6.)
¯ SECURELYassemble the SEATPAD(10) to the FRONTUPRIGHT(2) using two 3/8 X 2-3/4" BOLTS(30) and two
WASHERS(25). See FIGURE
SECURELYtighten all connections madeto up to this point.
[ 1/2 ] 1/2 ] 1/2 ] 1/2 ] 1/2 ]
34 501 2, ,, I i i [ I l i [ I i
’
8
112--1

X2-3/4"
FIGURE 7
STEP7:
¯ Route the CABLE(12) through the TOPBOOM(4) as shown in FIGURE
¯SECURELYassemble three 3-1/2" PULLEYS(14) to the slots in TOPBOOM(4) using three 3/8 X2-3/4" BOLTS(30), six
FLANGESPACERS(34), and three 3/8" LOCKNUTS(26) as shown in FIGURE7. (NOTE:Makesure the cable is routed
all the pulleys.)
¯ Slide two 5" VINYLCAPS(22) over the lat bar holder bracket on the TOPBOOM(4) as shownin FIGURE

3/8 X2-1/4"
!IMPORTANT!
/--- SECURELY
TIGHTEN
FIGURE 8 ’ ..
STEP8:
¯Attach the CABLE(12) from the TOPBOOM(4) to the CARRIAGE(5) using one QUICKLINK(37) as shown in FIGURE
(IMPORTANT!Securely tighten QUICKLINK.)
¯Place one 4-1/2" PULLEY(15) into the loop of the CABLE(12) below the second and third PULLEYofth~ TOPBOOM(4)
shown in FIGURE8.
¯SECURELYassemble two 1/4 x 2 x 7-1/4 .... PLATES(9) to each side of the 4-1/2" PULLEY(15) using o~e 3/8 X 2-1/4"
BOLT(29), two 3/8" WASHERS(25), and one 3/8" LOCKNUT(26). See FIGURE
I 1/2 [ 1/2 I 1/2 [ 1/2 I 1/2 l 1/2
01 2 345 6
10