ParaBody 874104 Mounting instructions

874104
MULTI-ANGLE BENCH
PRODUCT ASSEMBLY
INSTRUCTIONS SHEETS
8741O4
2,15/95

874104 MULTI-ANGLE BENCH ASSEMBLY PARTS LIST
SORT AND COUNTALL PARTS BEFORE BEGINNING ASSEMBLY
HARDWARE:
ITEM NAME/DESCRIPTION QTY
3.
4.
5.
6.
7.
8.
9.
10.
12.
13.
14.
15.
16.
17.
3/8
318
1!2
3/4
31,’I
318
3/8
X3IN.BOLT...................................................................................................................4
XI-I/4IN.BOLT............................................................................................................. 6
x8IN,BOLT......................................................................................................................I
IN.WASHER.................................................................................................................... 1
IN.WASHER.................................................................................................................. 14
IN.LOCKWASHER........................................................................................................ 6
IN. LOCKNUT................. : ..............................................................................................4
IN.LOWHEIGHTLOCKNUT......................................................................................... 1
3/4IN.FLANGEBEARING.................................................................................................. 4
STARLOCKCOLLAR.......................................................................................................... 2
SPRINGPINASSEMBLY..................................................................................................... I
I/2XI IN,SPRING............................................................................................................... 1
PALNUT................................................................................................................................1
THUMBSCREW..................................................................................................................... 1
2IN.,gO.ENDCAP................................................................................................................ 6
I-.3/4IN.SQ.ENDCAP......................................................................................................... 2
PARAGLIDESTRIP(8PER)................................................................................................. 1
WELI)MENTS/PARTS:
ITEM NAME/DESCRIPTION
6,
7,
8.
BENCI4FRAMEWLDMT. ............................................ (6475401)....................................... 1
SWIVELWLDMT..................... .~...................................(6474901)....................................... 1
ADJUSTMENTSLIDEWLDMT................................... (6415001).......................................
PADSUPPORTWLDMF.............................................. (6517101)....................................... 1
REARBASETUBE........................................................ (6236501)....................................... I
17RONTBASETUBE..................................................... (6259101)....................................... 1
HINGETAB................................................................... (6406401)....................................... 2
U-PIN....................................... : ......................................
(6406S01).......................................
SEA[PAD...................................................................... (6452501)....................................... I
BACKPAD..................................................................... (651721)1)....................................... 1
NOTE: BOLT LENGTHIS MEASUREDFROMTHE UNDERSIDEOF THE HEADOF THE BOLT.
,///////
BOLT LENGTH
BOLT LENGTIt RULER:
4 6
I 2 J 1 I I ,I,,J s

874104 MULTI-ANGLE BENCH ASSEMBLY INSTRUCTIONS
INSTRU
TI4E
ASSURE ITS PROPER FUNCTION.
IF YOU EXPERIENCE ANY
CONTACT YOUR DEALER OR
AT: !-80/t-328-9714
TOOLSREQUIRED:RATCHET,
RUBBER MALLET or HAMMER
Insert one (I) U-PIN through the POSTon the BENCHFRAME,as shown on drawing. Slide one (t)
X I IN. ~ ~ ~,ING over the U-PIN. Attach one (1) PALNUTto the end of the U-PIN.
Insert two (2) 2 IN. SQ. ENDCAPSinto both eiads of the REARBASETUBEas shown on drawing.
SECURELYassemble the REARBASE TUBEto the BENCHFRAMEas shown on drawing, using two
~ , two 3/8 IN. LOCKNUTS.
_ } ~ ~ X 3 IN. BOLTS,Ibm" (4) :/8 IN. WASHERS,and (2)
Insert two (2) 2 IN. SQ. ENDCAPSinto both ends of the FRONTBASETUBEas shown on drawing.
SECURELYassemble the FRONTBASE TUBEto the BENCHFRAMEas shown on drawing, using
two (2) 3:3 X 3 IN. BOLTS,ibm (4) 3/8 IN. WASHERS,and two (2) 3/8 IN. LOCK
Insert one { t) 2 IN. SQ. ENDCAPinto the end of the PADSUPPORTas shown on drawing.
Loosely assemble the PAD SUPPORTand two (2) HINGE TABS to the BUSHINGon the BENCH
FRA~E using one (I) 1/2 X 8 IN. BOLT and one (1) 1/2 LOWHEIGHT LOCKNUT.(DO NOT
TIGHTEN THE BOLT. THE PAD SUPPORT MUST ROTATE FREELY.)
Attach eight (8) PARAGLIDESTRIPS to both etads of the SWIVELas shown in (DETAILA) using
lk)llowing steps:
¯I-horouglaly clean all surli~ces where the PARAGLIDESTRIPSare to be attached.
¯Removepaper backing fi’om the PARAGLIDESTRIPSand firmly apply them to all slnown surfaces.

874104 MULTI-ANGLE BENCH ASSEMBLY INSTRUCTIONS
9. SECURELYAssemble one ( I ) SPRINGPIN ASSEMBLYto the SWIVEL, as shown in (DETAIL
10. Insert two (2) 3/4 IN. FLANGEBEARINGSinto the BUSHINGon the BENCHFRAMEas shown
drawing.
h3sert the SHAFTof the SWIVELthrough the 3/4 IN. FLANGEBEARINGSon ti~e BENCHFRAMEas
shown on drawing, and SECUREin place with one (1) STARLOCKCOLLAR.
12. Insert two (2) 3/4 IN. FLANGEBEARINGSinto the BUSHINGon the PADSUPPORTas shown
dra\\.’il~g.
14. [nser~ two (2) I-3/4 IN. SQ. ENDCAPSinto both ends of the ADJUSTMENTSLIDEas shown
drawin,~.
15.
16.
Slide one (1) 3/4"IN. WASIqERover the SHAFTof the ADJUSTMENTSLIDE. Insert the SHAFT
Ihe AD,IUSTMENTSLIDE lhrougl l the 3/4 IN. FLANGEBEARINGSon the PAD SUPPORTas shown
on drawing, and SECUREin place with one (1) STARLOCKCOLLAR.
Pull back the SPRINGPIN on the SWIVEL,and insert the ADJUSTMENTSLIDE, down t~ the first
adjt|smlent hole. Release the SPRINGPIN into the hole.
17. SECURELYattach the BACKPADto the PADSUPPORTusing foul" (4) 3/8 X 1-1/4 IN.BOLTS, tbur
(4) 3:8 IN. LOCKWASIIERS. and four (4)3/8 IN. WASHERS.
.’-;F.CURELY attach the SEATPADto the HINGETABSusing two (2) 3/8 X 1-I/4 IN.BOLTS. two (2)
LOCKWASHERS.and lwo (2) 3/8 IN. WASHERS.
19. [o adjust the SEATPADlbr the LEGEXTENSIONposition, pull out on the U-PIN. Rotate the U-PIN
back pass the FIRSTPIN STOP. Release the U-PIN, and allow it to rest up against the FIRSTPIN
STOP.
20. ’Fo ad.iust the SEATPADibr rl~e DECLINEor INCLINEposition, rotate the U-PINback to the
SKCONID PIN STOP.
21. The exlra 2 IN. SQ. ENDCAP is for the top of the UPRIGHTTUBEon the BENCHFRAME.If
attachmenls will be used. this CAPwill not be needed.
Ilasert one ( I ) THUMBSCREWinto the UPRIGHTTUBEof the BENCHFRAMEas shown on drawing.
This will be used for secu|ing attaclu’nents in place.

,$