ParaBody Leg Press 100101 User manual

1001 O1 LEGPRESS
WARNING:
Readand follow all directions
for eachstep to insure proper
assemblyof thi,,; product.
ASSEMBLYINSTRUCTIONS
Part # 7037301
Rev. A 1 Revision: 12/4/00

]IMPORTANT NOTES]
Please note:
* Thankyou for purchasing the Parabody100101LEGPRESS.Please read these instructions
thoroughlyand keepthemfor future reference. This productmustbe assembledon a flat,
level surface to assure its properfunction.
Werecommendcleaning your product (pads and flame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchasedflomyour Parabodycustomerservice representative
at [phone].
Thereis a risk assumedbyindividuals whouse this type of equipment.Tominirnizerisk, please
followthese rules:
1. Inspect equipmentdaily. Tightenall loose connectionsand replace wornp~:ts immediately.
Failureto doso mayresult in seriousinjury.
2. Donot allowminorsor children to play on or aroundthis equipment.
3. Exercisewithcare to avoidinjury.
4. If unsureof properuse of equipment,call yourlocal Parabodydistributor or call the
Parabodycustomerservice departmentat [phone].
5. Consulta physician before beginningany exercise program.
[ Tools Requiredfor Assembly]
* 3/4" wrench
* 9/16" wrench
* Ratchetwith 3/4" and9/16"sockets
* Adjustable wrench
* 5/32" Mien wrench
* Tape measure
Bolt LengthRuler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER: BOLT LENGTH I
I1/2 ] 1/2 ]
21/2 ] 1/2 [ 1/2 ] 1/2 ]
3 4 5 6
2

!KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART #DESCRIPTION
6574508 BASE FRAME
6573608 SEATFRAME
6575008 REAR TUBE
6575408 FOOT PLATE
6573908
6476408
6575102
LEVERTUBE
HANDLE
ADJUSTMENTTUBE
6597421 SEATPAD
6574001 3/4 X8-1/4" SHAFT
3103102 1X8" GRIP
3116201 3-1/2" PULLEY
6177001 2-1/2 X 5-1/2" NON-SKIDSTRIP
6405201 2" SQ. ENDCAP
6416601 PARAGLIDE(QTY. 8)
6467001 2" SQ. COVERCAP
6500601 2" WHEEL
3102501 3/8" FLATWASHER
PARTSLIST
QTY KEY
118
, 1 19
120
121
2 22
123
124
225
2 26
227
1 28
8 29
14 30
131
2 32
2 33
8
PART# DESCRIP 3N
3102601 3/8" LOCKWASHER
3102802
3102807
3102801
3102804
3102941
3/8" LOC) NUT
3/8" LOWHEIGH’ LOCKNUT
1/2" LOCI{NUT
1/2" LOWHEIGHT LOCKNUT
3/8 X1-1/2" BOLT
3102922 3/8 X2-3/4" BOLT
3102904 3/8 X 3" BOLT
3102935 3/8 X4-1/2" BOLT
3102918 1/2 X3-1/4" BOLT
3202107 1/2 X6-1/2" BOLT
6122703 3/8 ID X 3/8" SPACER
6020601 1/2" FLANGEBEARING
3104901 3/4" FLANGEBEARING
3106803 5/16" SET SCREW
6412001 3/8" SPRIN~3 PIN
QT¥
4
2
1
2
2
2
2
2
1
2
2
2
8
4
4
1
3

3/8
FIGURE 1
STEP1:
¯ Attach two 2" SQ. COVERCAPS(15) onto the ends &the REARTUBE(3) as shown in FIGURE
¯ Insert four 2" SQ. ENDCAPS(13) into the ends of the BASEFRAME(1) as shownin FIGURE
SECURELYassemble the REARTUBE(3) to the BASEFRAME(1) using two 3/8 X 3" BOLTS(25), 278" FLATWASHERS
(17), and two 3/8" LOCKNUTS(19). See FIGURE
] 1/2 I1/2 I1/2 [ I/2 [ 1/2 [ 1/:! I
01 2 3 4 56
4

I
/
/
FIGURE 2
STEP2:
¯Insert two 2" SQ. ENDCAPS(13) into file ends of the SEATFRAME(2) as shownin FIGURE
¯SECURELYassemble one 3/8" SPRINGPIN (33) to the spring pin barrel on the SEATFRAME(2) as shownin FIGURE
¯Attach four PARAGLIDESTRIPS(14) to the inside of the SEATFRA~£E(2) using file following steps:
¯Thoroughlyclean all surfaces wherethe PARAGLIDESTRIPS(14) are to be attached.
¯l~emovethe PARAGLIDESTRIPS(14) from the paper backing and firmly apply them to all shownsurfaces.
5

3/8" LOWHEIGHT
/
FIGURE3
STEP 3:
¯SECURELYassemble one 3-1/2" PULLEY(11), two 2" WHEELS(16), two 3/8" FLATWASHERS(17):. and two 3/8 ID
SPACERS(29) to the ADJUSTMENTTUBE(7) using one 3/8 X 4-1/2" BOLT(26) as shown in FIGURE
¯ Attach four PARAGLIDESTRIPS(14) to the outside of the ADJUSTMENTTUBE(7) using the followirtg steps:
¯Thoroughlyclean all surfaces wherethe PARAGLtDESTRIPS(14) are to be attached.
¯Removethe PARAGLIDESTRIPS(t4) from the paper backing and firmly apply them to all shownsurfaces.
1/2 I 1/2 I 1/2 I 1/2 I 1/2 I 1/2 I
3 4 5 6

PIN
FIGURE4
STEP4:
¯ CAREFULLE¥slide the ADJUSTMENTTUBE(7) over into the SEATFRAME(2) and engage the SPRINGPINinto one
the adjustmentholes. See FIGURE4.
FIGURE5
STEP5:
¯Insert two 3/4" FLANGEBEARINGSinto
each of the twoLEVERTUBES(5)
shownin FIGURE5.

5/16" SET SCREW~
FIGURE 6
STEP6:
¯ Insert four 2" SQ.ENDCAPS(13) into the ends of twoLEVERTUBES(5) as shownin FIGURE
¯SECURELYassemble the LEVERTUBES(5) to the BASEFRAME(1) using two 3/4" SHAFTS(9) and. SECUREin
using four 5/16" SETSCREWS(32). See FIGURE
1/2 I1/2 I 1/2 I 1/2 [1/2 6
4I
2I I I I

FIGURE 7
STEP7:
¯ Insert four2" SQ.ENDCAPS(13) into the endsof FOOTPLATE(4) as shownin FIGURE
¯ Insert eight 1/2" FLANGEBEARING(30) into the LEVERTUBES(5) as shownin FIGURE

1/2" LOW HEIGHT @~’""
FIGURE 8
STEP8:
¯ SECURELYassemble the FOOTPLATE(4) to the LEVERTUBES(5) using two 1/2 X 6-1/2" BOLTS(28) and two 1/2"
HEIGHTLOCKNUTS(22) as shown in FIGURE
¯ CAREFULLYattach eight NON-SKIDSTRIPS(12) to the FOOTPLATE(4) as shown in FIGURE