ParaBody Leg Press 100 User manual

100 LEG PRESS
CLASSH
PART# 7155801
REV. B
Version: 100102
Revision: 09/26/01
1
ASSEMBLY INSTRUCTIONS
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the Parabody 100102 LEG PRESS. Please read these instructions
thoroughly and keep them for future reference. This product must be assembled on a flat,
level surface to assure its proper function.
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
2
NOTE:BOLTLENGTHISMEASUREDFROMTHE UNDERSIDE OFTHEHEADOFTHEBOLT.
BOLT LENGTH RULER:
We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
BoltLengthRuler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].
BOLT LENGTH
5. Consult a physician before beginning any exercise program.

3
PARTS LIST
PART #
7140508
7140802
6806208
7140608
7140708
7140908
7128108
6994721
3102922
KEY
1
2
3
4
5
6
7
8
9
QTY
1
1
1
1
1
1
1
2
6
PART #
3102501
3102802
3102944
3102801
3104901
6416601
7115201
7128201
6140701
DESCRIPTION
3/8” FLAT WASHER
3/8” LOCK NUT
1/2 X 5” BOLT
1/2” LOCK NUT
3/4” FLANGE BEARING
PARAGLIDE (QTY8)
SPRING PIN
3/4 X 4” SHAFT
1” SQ. GLIDE
QTY
8
2
4
4
8
1
1
4
2
DESCRIPTION
FRAME
SEATADJUST
HANDLE
MAINARM
SECONDARM
FOOTPLATE
PULLEYBRACKET
PAD
3/8 X 2-3/4” BOLT
KEY
10
11
12
13
14
15
16
17
18

9-1/2"
4
FIGURE 1
STEP 1:
• SECURELY assemble the SECOND ARM (5) to the FRAME (1) using one 1/2 X 5” BOLT (12), two 3/4” FLANGE BEARINGS
(14), one 3/4 X 4” SHAFT (17) and one 1/2” LOCK NUT (13). See FIGURE 1.
0123456
1/2 1/2 1/2 1/2 1/2 1/2
12 1/2 X 5”
1
13
17
14
4
5
• SECURELY assemble the MAIN ARM (4) to the FRAME (1) using one 1/2 X 5” BOLT (12), two 3/4” FLANGE BEARINGS (14),
one 3/4 X 4” SHAFT (17) and one 1/2” LOCK NUT (13). See FIGURE 1. (NOTE: Make sure MAIN ARM is orientated cor-
rectly, top hole should be 9-1/2” from the top of arm as shown in FIGURE 1.)
• NOTE: Follow STEP 1 for the assembly of the LEG PRESS to the 220 and 880 Gym Systems. If you have the 777 Gym
System proceed to STEP 2.
• Proceed to to STEP 3.
• SECURELY assemble two 1” SQ. GLIDES (18) to each side of the MAINARM (4) where the MAINARM (4) contacts the FRAME
(1) See FIGURE 1.
18
For assembly to the the 220 and 880 Gym Systems .
Make sure MAINARM
is orientated correctly

11-1/4"
5
FIGURE 2
STEP 2:
• SECURELY assemble the SECOND ARM (5) to the FRAME (1) using one 1/2 X 5” BOLT (12), two 3/4” FLANGE BEARINGS
(14), one 3/4 X 4” SHAFT (17) and one 1/2” LOCK NUT (13). See FIGURE 2.
• SECURELY assemble the MAIN ARM (4) to the FRAME (1) using one 1/2 X 5” BOLT (12), two 3/4” FLANGE BEARINGS (14),
one 3/4 X 4” SHAFT (17) and one 1/2” LOCK NUT (13). See FIGURE 2. (NOTE: Make sure MAIN ARM is orientated cor-
rectly, top hole should be 11-1/4” from the top of arm as shown in FIGURE 2.)
• NOTE: Follow STEP 2 for the assembly of the LEG PRESS to the 777 Gym System. If you have the 220 or 880 Gym Systems
proceed to STEP 3.
• Proceed to to STEP 3.
• SECURELY assemble two 1” SQ. GLIDES (18) to each side of the MAINARM (4) where the MAINARM (4) contacts the FRAME
(1) See FIGURE 2.
12 1/2 X 5”
1
13
17
14
4
5
18
For assembly to the the 777 Gym System .
Make sure MAINARM
is orientated correctly

FIGURE 3
STEP 3:
6
• Insert two 3/4” FLANGE BEARINGS (14) and one 3/4 X 4” SHAFT (17) into the SECONDARM (5) as shown in FIGURE 3.
• Insert two 3/4” FLANGE BEARINGS (14) and one 3/4 X 4” SHAFT (17) into the MAINARM (4) as shown in FIGURE 3.
17
14
4
5
0123456
1/2 1/2 1/2 1/2 1/2 1/2

7
STEP4:
FIGURE 4
• SECURELY assemble the FOOTPLATE (6) to the SECONDARM (5) and the MAINARM (4) using two 1/2 X 5” BOLTS (12) and
two 1/2” LOCK NUTS (13). See FIGURE 4.
12 1/2 X 5”
6
5
13
4

8
STEP5:
FIGURE 5
3/8 X 2-3/4” 9
1
11
10
3
• SECURELY assemble the HANDLE (3) to the FRAME (1) using two 3/8 X 2-3/4” BOLTS (9), four 3/8” FLAT WASHERS (10)
and two 3/8” LOCK NUTS (11) as shown in FIGURE 5.
0123456
1/2 1/2 1/2 1/2 1/2 1/2

9
STEP6:
FIGURE 6
• CAREFULLEY slide the SEAT ADJUST (2) into the FRAME (1) and engage the SPRING PIN into one of the adjustment holes.
See FIGURE 6.
• Attach eight PARAGLIDE STRIPS (15) to the inside of the tube on the FRAME (1) using the following steps:
• Thoroughly clean all surfaces where the PARAGLIDE STRIPS (15) are to be attached.
• Remove the PARAGLIDE STRIPS (15) from the paper backing and firmly apply them to all shown surfaces.
• SECURELY assemble one SPRING PIN (16) to the spring pin barrel on the FRAME (1) as shown in FIGURE 6.
1
15
2
16

STEP7:
FIGURE 7
• SECURELY assemble one PAD (8) to the SEATADJUST (2) using two 3/8 X 2-3/4” BOLTS (9) and two 3/8” FLAT WASHERS
(10) as shown in FIGURE 7.
9 3/8 X 2-3/4”
10
2
8
10
0123456
1/2 1/2 1/2 1/2 1/2 1/2