PAX E700 User manual

1.When the printer is out of paper,
the yellow “Paper Out” indicator
lights. Press the button on the left
of printer to open the cover.
E700
Integrated Smart Terminal
Load Printer Paper
2. Load the paper roll into the paper
compartment and extend the end
of the paper out of the printer.
3. Close printer cover. The Paper
Out indicator light turns off.
•
strong electromagnetic environment.
• Do not vibrate, shake, or drop the device.
• Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
• Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate
measures.
Avoid exposing the device to an excessively hot, humid, dusty, or
Peripheral Ports: Power port x 1
USB A ports x 4
USB C port x 1
HDMI x 1
LAN x 1
Cash drawer x 1
Serial port x 1
Audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
Magnetic Card Reader: Supports track 1/2/3.
IC Card Reader: Conforms to the standard ofISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Magnetic Stripe Reader
Insert the card into the reader slot located on the top of the Q20. The
terminal reads the information from the card when the magnetic stripe is
inserted into the card slot.
EMV Card Reader
Insert the card with the front facing you and the chip down into the card
slot. Leave the card inserted until the terminal prompts to remove the card.
NFC/Contactless Card Reader
Tap the card to the Q20 screen when prompted. The terminal uses an
antenna device that detects and retrieves information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
Operation System: Android 7.1
CPU: Quad-core Cortex™-A53,1.8GHz
Memory: 2GB DDR+16GB eMMC
Main Display: 12.5 inch, 1920x1080 resolution, capacitive touch screen
Printer: 3" high-speed thermal printer with auto-cutter, printing
speed 150mm/s, paper width 80mm, diameter 80mm
Audio: Built-in speaker, support headphone output
Camera with scan window: (coverage of 30mm-120mm) for 1D/2D scan
• Front fixed focus camera with 0.3 mega pixels (cashier-facing)
• Rear fixed focus camera with 2 mega pixels (customer-facing)
L-Sensor (Ambient Light Sensor): Automatically adjusts the backlight
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth, 4G
Hybrid Card Reader
5
The Q20 on the consumer-facing side of
the E700 includes a reader that can be
used as a Magnetic Stripe, EMV, and
NFC/Contactless card reader.

P/N:200312000000407
E700
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Open the back cover to access following ports:
• SD Card Slot – Open card cover, remove battery and insert card into
SD card slot
• SIM Card Slot – Open card cover, remove battery and insert SIM
card into SIM slot to connect to cellular carrier’s network.
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Terminal Ports
Power ON/OFF
Power on: Press and hold the Power button for three seconds until the
main screen displays normally. (See page 1 for the location of the Power
button.
Power off: Press and hold the Power button for three seconds until the
shutdown menu displays. Select Power off. The terminal turns off after
a few seconds. (See page 1 for the location of the Power button.)
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Printer Button
LCD Display
Fingerprint Reader
Printer Paper Exit
Power & Printer Indicator
Power Button
Light Sensor
Cashier-facing Scanner
Customer-facing Scanner
Contactless Area
Hybrid Card Reader
Q20 View
Front View
Cash Drawer Port
Power Port
Battery Cover
HDMI Port Audio Jack RS232 Port
USB-A/B Host Port
LAN
Ports View
Side View
Volume+
Volume-
USB-Slave The following ports are accessible on the back of the E700:
• Power – Connect AC power supply to E700
• Cash Drawer – Insert the cable from cash drawer to connect with cash
register
• HDMI – Connect to HDMI device
• Audio Jack – Allows hearing impaired to connect assistive listening
device
• USB Host – Connect USB device
• RS232 – Used to connect to serial device such an external POS device
• USB-Slave – Connected to PC for local terminal download
• LAN – Used for bi-directional Ethernet connections
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us

P/N:200312000000407
E700
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Open the back cover to access following ports:
• SD Card Slot – Open card cover, remove battery and insert card into
SD card slot
• SIM Card Slot – Open card cover, remove battery and insert SIM
card into SIM slot to connect to cellular carrier’s network.
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Terminal Ports
Power ON/OFF
Power on: Press and hold the Power button for three seconds until the
main screen displays normally. (See page 1 for the location of the Power
button.
Power off: Press and hold the Power button for three seconds until the
shutdown menu displays. Select Power off. The terminal turns off after
a few seconds. (See page 1 for the location of the Power button.)
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Printer Button
LCD Display
Fingerprint Reader
Printer Paper Exit
Power & Printer Indicator
Power Button
Light Sensor
Cashier-facing Scanner
Customer-facing Scanner
Contactless Area
Hybrid Card Reader
Q20 View
Front View
Cash Drawer Port
Power Port
Battery Cover
HDMI Port Audio Jack RS232 Port
USB-A/B Host Port
LAN
Ports View
Side View
Volume+
Volume-
USB-Slave The following ports are accessible on the back of the E700:
• Power – Connect AC power supply to E700
• Cash Drawer – Insert the cable from cash drawer to connect with cash
register
• HDMI – Connect to HDMI device
• Audio Jack – Allows hearing impaired to connect assistive listening
device
• USB Host – Connect USB device
• RS232 – Used to connect to serial device such an external POS device
• USB-Slave – Connected to PC for local terminal download
• LAN – Used for bi-directional Ethernet connections
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us

P/N:200312000000407
E700
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Open the back cover to access following ports:
• SD Card Slot – Open card cover, remove battery and insert card into
SD card slot
• SIM Card Slot – Open card cover, remove battery and insert SIM
card into SIM slot to connect to cellular carrier’s network.
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Terminal Ports
Power ON/OFF
Power on: Press and hold the Power button for three seconds until the
main screen displays normally. (See page 1 for the location of the Power
button.
Power off: Press and hold the Power button for three seconds until the
shutdown menu displays. Select Power off. The terminal turns off after
a few seconds. (See page 1 for the location of the Power button.)
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Printer Button
LCD Display
Fingerprint Reader
Printer Paper Exit
Power & Printer Indicator
Power Button
Light Sensor
Cashier-facing Scanner
Customer-facing Scanner
Contactless Area
Hybrid Card Reader
Q20 View
Front View
Cash Drawer Port
Power Port
Battery Cover
HDMI Port Audio Jack RS232 Port
USB-A/B Host Port
LAN
Ports View
Side View
Volume+
Volume-
USB-Slave The following ports are accessible on the back of the E700:
• Power – Connect AC power supply to E700
• Cash Drawer – Insert the cable from cash drawer to connect with cash
register
• HDMI – Connect to HDMI device
• Audio Jack – Allows hearing impaired to connect assistive listening
device
• USB Host – Connect USB device
• RS232 – Used to connect to serial device such an external POS device
• USB-Slave – Connected to PC for local terminal download
• LAN – Used for bi-directional Ethernet connections
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us

P/N:200312000000407
E700
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Open the back cover to access following ports:
• SD Card Slot – Open card cover, remove battery and insert card into
SD card slot
• SIM Card Slot – Open card cover, remove battery and insert SIM
card into SIM slot to connect to cellular carrier’s network.
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Terminal Ports
Power ON/OFF
Power on: Press and hold the Power button for three seconds until the
main screen displays normally. (See page 1 for the location of the Power
button.
Power off: Press and hold the Power button for three seconds until the
shutdown menu displays. Select Power off. The terminal turns off after
a few seconds. (See page 1 for the location of the Power button.)
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Printer Button
LCD Display
Fingerprint Reader
Printer Paper Exit
Power & Printer Indicator
Power Button
Light Sensor
Cashier-facing Scanner
Customer-facing Scanner
Contactless Area
Hybrid Card Reader
Q20 View
Front View
Cash Drawer Port
Power Port
Battery Cover
HDMI Port Audio Jack RS232 Port
USB-A/B Host Port
LAN
Ports View
Side View
Volume+
Volume-
USB-Slave The following ports are accessible on the back of the E700:
• Power – Connect AC power supply to E700
• Cash Drawer – Insert the cable from cash drawer to connect with cash
register
• HDMI – Connect to HDMI device
• Audio Jack – Allows hearing impaired to connect assistive listening
device
• USB Host – Connect USB device
• RS232 – Used to connect to serial device such an external POS device
• USB-Slave – Connected to PC for local terminal download
• LAN – Used for bi-directional Ethernet connections
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us

1.When the printer is out of paper,
the yellow “Paper Out” indicator
lights. Press the button on the left
of printer to open the cover.
E700
Integrated Smart Terminal
Load Printer Paper
2. Load the paper roll into the paper
compartment and extend the end
of the paper out of the printer.
3. Close printer cover. The Paper
Out indicator light turns off.
•
strong electromagnetic environment.
• Do not vibrate, shake, or drop the device.
• Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
• Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate
measures.
Avoid exposing the device to an excessively hot, humid, dusty, or
Peripheral Ports: Power port x 1
USB A ports x 4
USB C port x 1
HDMI x 1
LAN x 1
Cash drawer x 1
Serial port x 1
Audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
Magnetic Card Reader: Supports track 1/2/3.
IC Card Reader: Conforms to the standard ofISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Magnetic Stripe Reader
Insert the card into the reader slot located on the top of the Q20. The
terminal reads the information from the card when the magnetic stripe is
inserted into the card slot.
EMV Card Reader
Insert the card with the front facing you and the chip down into the card
slot. Leave the card inserted until the terminal prompts to remove the card.
NFC/Contactless Card Reader
Tap the card to the Q20 screen when prompted. The terminal uses an
antenna device that detects and retrieves information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
Operation System: Android 7.1
CPU: Quad-core Cortex™-A53,1.8GHz
Memory: 2GB DDR+16GB eMMC
Main Display: 12.5 inch, 1920x1080 resolution, capacitive touch screen
Printer: 3" high-speed thermal printer with auto-cutter, printing
speed 150mm/s, paper width 80mm, diameter 80mm
Audio: Built-in speaker, support headphone output
Camera with scan window: (coverage of 30mm-120mm) for 1D/2D scan
• Front fixed focus camera with 0.3 mega pixels (cashier-facing)
• Rear fixed focus camera with 2 mega pixels (customer-facing)
L-Sensor (Ambient Light Sensor): Automatically adjusts the backlight
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth, 4G
Hybrid Card Reader
5
The Q20 on the consumer-facing side of
the E700 includes a reader that can be
used as a Magnetic Stripe, EMV, and
NFC/Contactless card reader.

1.When the printer is out of paper,
the yellow “Paper Out” indicator
lights. Press the button on the left
of printer to open the cover.
E700
Integrated Smart Terminal
Load Printer Paper
2. Load the paper roll into the paper
compartment and extend the end
of the paper out of the printer.
3. Close printer cover. The Paper
Out indicator light turns off.
•
strong electromagnetic environment.
• Do not vibrate, shake, or drop the device.
• Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
• Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate
measures.
Avoid exposing the device to an excessively hot, humid, dusty, or
Peripheral Ports: Power port x 1
USB A ports x 4
USB C port x 1
HDMI x 1
LAN x 1
Cash drawer x 1
Serial port x 1
Audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
Magnetic Card Reader: Supports track 1/2/3.
IC Card Reader: Conforms to the standard ofISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Magnetic Stripe Reader
Insert the card into the reader slot located on the top of the Q20. The
terminal reads the information from the card when the magnetic stripe is
inserted into the card slot.
EMV Card Reader
Insert the card with the front facing you and the chip down into the card
slot. Leave the card inserted until the terminal prompts to remove the card.
NFC/Contactless Card Reader
Tap the card to the Q20 screen when prompted. The terminal uses an
antenna device that detects and retrieves information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
Operation System: Android 7.1
CPU: Quad-core Cortex™-A53,1.8GHz
Memory: 2GB DDR+16GB eMMC
Main Display: 12.5 inch, 1920x1080 resolution, capacitive touch screen
Printer: 3" high-speed thermal printer with auto-cutter, printing
speed 150mm/s, paper width 80mm, diameter 80mm
Audio: Built-in speaker, support headphone output
Camera with scan window: (coverage of 30mm-120mm) for 1D/2D scan
• Front fixed focus camera with 0.3 mega pixels (cashier-facing)
• Rear fixed focus camera with 2 mega pixels (customer-facing)
L-Sensor (Ambient Light Sensor): Automatically adjusts the backlight
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth, 4G
Hybrid Card Reader
5
The Q20 on the consumer-facing side of
the E700 includes a reader that can be
used as a Magnetic Stripe, EMV, and
NFC/Contactless card reader.

1.When the printer is out of paper,
the yellow “Paper Out” indicator
lights. Press the button on the left
of printer to open the cover.
E700
Integrated Smart Terminal
Load Printer Paper
2. Load the paper roll into the paper
compartment and extend the end
of the paper out of the printer.
3. Close printer cover. The Paper
Out indicator light turns off.
•
strong electromagnetic environment.
• Do not vibrate, shake, or drop the device.
• Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
• Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate
measures.
Avoid exposing the device to an excessively hot, humid, dusty, or
Peripheral Ports: Power port x 1
USB A ports x 4
USB C port x 1
HDMI x 1
LAN x 1
Cash drawer x 1
Serial port x 1
Audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
Magnetic Card Reader: Supports track 1/2/3.
IC Card Reader: Conforms to the standard ofISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Magnetic Stripe Reader
Insert the card into the reader slot located on the top of the Q20. The
terminal reads the information from the card when the magnetic stripe is
inserted into the card slot.
EMV Card Reader
Insert the card with the front facing you and the chip down into the card
slot. Leave the card inserted until the terminal prompts to remove the card.
NFC/Contactless Card Reader
Tap the card to the Q20 screen when prompted. The terminal uses an
antenna device that detects and retrieves information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
Operation System: Android 7.1
CPU: Quad-core Cortex™-A53,1.8GHz
Memory: 2GB DDR+16GB eMMC
Main Display: 12.5 inch, 1920x1080 resolution, capacitive touch screen
Printer: 3" high-speed thermal printer with auto-cutter, printing
speed 150mm/s, paper width 80mm, diameter 80mm
Audio: Built-in speaker, support headphone output
Camera with scan window: (coverage of 30mm-120mm) for 1D/2D scan
• Front fixed focus camera with 0.3 mega pixels (cashier-facing)
• Rear fixed focus camera with 2 mega pixels (customer-facing)
L-Sensor (Ambient Light Sensor): Automatically adjusts the backlight
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth, 4G
Hybrid Card Reader
5
The Q20 on the consumer-facing side of
the E700 includes a reader that can be
used as a Magnetic Stripe, EMV, and
NFC/Contactless card reader.

1.When the printer is out of paper,
the yellow “Paper Out” indicator
lights. Press the button on the left
of printer to open the cover.
E700
Integrated Smart Terminal
Load Printer Paper
2. Load the paper roll into the paper
compartment and extend the end
of the paper out of the printer.
3. Close printer cover. The Paper
Out indicator light turns off.
•
strong electromagnetic environment.
• Do not vibrate, shake, or drop the device.
• Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
• Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate
measures.
Avoid exposing the device to an excessively hot, humid, dusty, or
Peripheral Ports: Power port x 1
USB A ports x 4
USB C port x 1
HDMI x 1
LAN x 1
Cash drawer x 1
Serial port x 1
Audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
Magnetic Card Reader: Supports track 1/2/3.
IC Card Reader: Conforms to the standard ofISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Magnetic Stripe Reader
Insert the card into the reader slot located on the top of the Q20. The
terminal reads the information from the card when the magnetic stripe is
inserted into the card slot.
EMV Card Reader
Insert the card with the front facing you and the chip down into the card
slot. Leave the card inserted until the terminal prompts to remove the card.
NFC/Contactless Card Reader
Tap the card to the Q20 screen when prompted. The terminal uses an
antenna device that detects and retrieves information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
Operation System: Android 7.1
CPU: Quad-core Cortex™-A53,1.8GHz
Memory: 2GB DDR+16GB eMMC
Main Display: 12.5 inch, 1920x1080 resolution, capacitive touch screen
Printer: 3" high-speed thermal printer with auto-cutter, printing
speed 150mm/s, paper width 80mm, diameter 80mm
Audio: Built-in speaker, support headphone output
Camera with scan window: (coverage of 30mm-120mm) for 1D/2D scan
• Front fixed focus camera with 0.3 mega pixels (cashier-facing)
• Rear fixed focus camera with 2 mega pixels (customer-facing)
L-Sensor (Ambient Light Sensor): Automatically adjusts the backlight
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth, 4G
Hybrid Card Reader
5
The Q20 on the consumer-facing side of
the E700 includes a reader that can be
used as a Magnetic Stripe, EMV, and
NFC/Contactless card reader.

P/N:200312000000407
E700
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Open the back cover to access following ports:
• SD Card Slot – Open card cover, remove battery and insert card into
SD card slot
• SIM Card Slot – Open card cover, remove battery and insert SIM
card into SIM slot to connect to cellular carrier’s network.
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Terminal Ports
Power ON/OFF
Power on: Press and hold the Power button for three seconds until the
main screen displays normally. (See page 1 for the location of the Power
button.
Power off: Press and hold the Power button for three seconds until the
shutdown menu displays. Select Power off. The terminal turns off after
a few seconds. (See page 1 for the location of the Power button.)
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. All rights reserved.
Printer Button
LCD Display
Fingerprint Reader
Printer Paper Exit
Power & Printer Indicator
Power Button
Light Sensor
Cashier-facing Scanner
Customer-facing Scanner
Contactless Area
Hybrid Card Reader
Q20 View
Front View
Cash Drawer Port
Power Port
Battery Cover
HDMI Port Audio Jack RS232 Port
USB-A/B Host Port
LAN
Ports View
Side View
Volume+
Volume-
USB-Slave The following ports are accessible on the back of the E700:
• Power – Connect AC power supply to E700
• Cash Drawer – Insert the cable from cash drawer to connect with cash
register
• HDMI – Connect to HDMI device
• Audio Jack – Allows hearing impaired to connect assistive listening
device
• USB Host – Connect USB device
• RS232 – Used to connect to serial device such an external POS device
• USB-Slave – Connected to PC for local terminal download
• LAN – Used for bi-directional Ethernet connections
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us