PAX E800 User manual

1.When the printer is out of paper,
the yellow "Paper Out" indicator
lights. Open the external printer
cover by inserting your finger into
a recessed area to the side of the
door and pulling outward.
E800
Integrated Smart Terminal
Load Printer Paper
2. Open the built-in printer cover by
pressing in the latch, as shown.
The printer door will slowly open.
3. Load the paper roll, as shown.
Extend the end of the paper roll
out of the printer.
4. Press both sides of the built-in
printer cover until it snaps closed.
Close the external printer cover.
The Paper Out indicator light turns
off.
Avoid exposing the device to an excessively hot, humid, dusty, or
strong electromagnetic environment.
·Do not vibrate, shake, or drop the device.
·Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
·Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
tooperate the equipment. In a domestic environment, this product may
cause radio interference in which case the user may be required
to take adequate measures.
Peripheral Ports: Micro-USB port x 1
USB ports x 5
Network ports x 3 (WAN port x 1, LAN ports x 2)
Cash Drawer x 1
serial port x 1
audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
magnetic stripe card/IC card slot x 1, using
two-in-one（support MAG&ICC）
Magnetic Card Reader: Supports track 1/2/3
IC Card Reader: Conforms to the standard of ISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Operating System: Android 6.0
CPU: Quad-coreA17,1.8GHZ processor
Memory: 2GB RAM + 16GB Flash Memory
Main Display: 15.6 inch, resolution: 1920*1080, multi-touch
capacitive touch screen
Guest Display: 8 inch, resolution: 1280*800, multi-touch capacitive
touch screen
Printer: 3" high-speed thermal printer with auto-cutter,
printing speed:150mm/s
Audio: supports headphone output
Camera: 5 mega-pixel auto-focusing camera, high-speed
EMV Card Reader
To use the EMV Card Reader, insert the card with the front facing you and
the chip down into the card slot. Leave the card inserted until the terminal
prompts to remove the card.
NFC/Contactless Card Reader
To use the NFC/Contactless Reader, tap the card to the Q20 screen when
prompted. The terminal uses an antenna device that detects and retrieves
information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
code scanning
L-Sensor (Ambient Light Sensor): automatically adjusts the backl
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth®
wireless technology , 3G/4G(optional)
ight

P/N:200312000000426
E800
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Light Sensor
Printer CoverOpening
Advance Paper
Q20
SIM Card/SD Card Cover USB Port
Main Display
Printer Paper Exit
Printer Cover
Open Printer Cover
Printer Indicators:
Power
Out of Paper
Printer Error
Main Display Guest Display
Loudspeaker
Heat Emission Holes
Back Cover
Magnetic Stripe
Card/IC Card Slot
Contactless Reader
Scanning Camera
Guest Display
WAN
LAN x 2
USB x 4
Micro USB
Micro SD Card Slot
USB Port
Audio Jack
Power Port Back Cover
Serial Port
Cash Drawer Interface
The following ports are accessible on the side of the E800:
· Micro SD Card Slot – Open card cover and insert card into TF slot
· SIM Card Slot – Open card cover and insert SIM card into SIM slot to
connect to cellular carrier’s network
· USB – Connect USB device without opening back cover
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Power Button
Terminal Ports
Open the back cover to access the following ports:
·Power – Connect AC power supply to E800
·Audio Jack – Allows hearing impaired to connect assistive listening
device
·Cash Drawer – Insert the cable from cash drawer to connect with
cash register
·WAN – Insert cable connected to the Internet to provide wired network
for cash register
·LAN – Used for bi-directional Ethernet connections
·RS232 – Used to connect to serial device such an external POS
device or check reader
·Micro USB – Connect Micro USB device
·USB-OTG – Used for local terminal downloads or external peripherals
·USB – Connect USB device
Power ON/OFF
1. Power on: Press and hold the Power button (on the side) for three
seconds until the main screen displays normally. (See page 2 for the
location of the Power button.
2. Power off: Press and hold the Power button (on the side) for three
seconds until the shutdown menu displays. Select Power off. The
terminal turns off after a few seconds. (See page 2 for the location of
the Power button.)
Hybrid Card Reader
5
The Q20 on the consumer-facing side of the
E800 includes a reader that can be used as a
Magnetic Stripe, EMV, and NFC/Contactless
card reader.
Magnetic Stripe Reader
To use the Magnetic Stripe Reader, insert the
card into the reader slot located on the top of
the Q20. The terminal reads the information
from the card when the magnetic stripe is
inserted into the card slot.
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. The Bluetooth® word mark
and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by PAX Technology, Inc. is under
license. Other trademarks and trade names are those of their
respective owners.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us

P/N:200312000000426
E800
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Light Sensor
Printer CoverOpening
Advance Paper
Q20
SIM Card/SD Card Cover USB Port
Main Display
Printer Paper Exit
Printer Cover
Open Printer Cover
Printer Indicators:
Power
Out of Paper
Printer Error
Main Display Guest Display
Loudspeaker
Heat Emission Holes
Back Cover
Magnetic Stripe
Card/IC Card Slot
Contactless Reader
Scanning Camera
Guest Display
WAN
LAN x 2
USB x 4
Micro USB
Micro SD Card Slot
USB Port
Audio Jack
Power Port Back Cover
Serial Port
Cash Drawer Interface
The following ports are accessible on the side of the E800:
· Micro SD Card Slot – Open card cover and insert card into TF slot
· SIM Card Slot – Open card cover and insert SIM card into SIM slot to
connect to cellular carrier’s network
· USB – Connect USB device without opening back cover
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Power Button
Terminal Ports
Open the back cover to access the following ports:
·Power – Connect AC power supply to E800
·Audio Jack – Allows hearing impaired to connect assistive listening
device
·Cash Drawer – Insert the cable from cash drawer to connect with
cash register
·WAN – Insert cable connected to the Internet to provide wired network
for cash register
·LAN – Used for bi-directional Ethernet connections
·RS232 – Used to connect to serial device such an external POS
device or check reader
·Micro USB – Connect Micro USB device
·USB-OTG – Used for local terminal downloads or external peripherals
·USB – Connect USB device
Power ON/OFF
1. Power on: Press and hold the Power button (on the side) for three
seconds until the main screen displays normally. (See page 2 for the
location of the Power button.
2. Power off: Press and hold the Power button (on the side) for three
seconds until the shutdown menu displays. Select Power off. The
terminal turns off after a few seconds. (See page 2 for the location of
the Power button.)
Hybrid Card Reader
5
The Q20 on the consumer-facing side of the
E800 includes a reader that can be used as a
Magnetic Stripe, EMV, and NFC/Contactless
card reader.
Magnetic Stripe Reader
To use the Magnetic Stripe Reader, insert the
card into the reader slot located on the top of
the Q20. The terminal reads the information
from the card when the magnetic stripe is
inserted into the card slot.
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. The Bluetooth® word mark
and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by PAX Technology, Inc. is under
license. Other trademarks and trade names are those of their
respective owners.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us

P/N:200312000000426
E800
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Light Sensor
Printer CoverOpening
Advance Paper
Q20
SIM Card/SD Card Cover USB Port
Main Display
Printer Paper Exit
Printer Cover
Open Printer Cover
Printer Indicators:
Power
Out of Paper
Printer Error
Main Display Guest Display
Loudspeaker
Heat Emission Holes
Back Cover
Magnetic Stripe
Card/IC Card Slot
Contactless Reader
Scanning Camera
Guest Display
WAN
LAN x 2
USB x 4
Micro USB
Micro SD Card Slot
USB Port
Audio Jack
Power Port Back Cover
Serial Port
Cash Drawer Interface
The following ports are accessible on the side of the E800:
· Micro SD Card Slot – Open card cover and insert card into TF slot
· SIM Card Slot – Open card cover and insert SIM card into SIM slot to
connect to cellular carrier’s network
· USB – Connect USB device without opening back cover
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Power Button
Terminal Ports
Open the back cover to access the following ports:
·Power – Connect AC power supply to E800
·Audio Jack – Allows hearing impaired to connect assistive listening
device
·Cash Drawer – Insert the cable from cash drawer to connect with
cash register
·WAN – Insert cable connected to the Internet to provide wired network
for cash register
·LAN – Used for bi-directional Ethernet connections
·RS232 – Used to connect to serial device such an external POS
device or check reader
·Micro USB – Connect Micro USB device
·USB-OTG – Used for local terminal downloads or external peripherals
·USB – Connect USB device
Power ON/OFF
1. Power on: Press and hold the Power button (on the side) for three
seconds until the main screen displays normally. (See page 2 for the
location of the Power button.
2. Power off: Press and hold the Power button (on the side) for three
seconds until the shutdown menu displays. Select Power off. The
terminal turns off after a few seconds. (See page 2 for the location of
the Power button.)
Hybrid Card Reader
5
The Q20 on the consumer-facing side of the
E800 includes a reader that can be used as a
Magnetic Stripe, EMV, and NFC/Contactless
card reader.
Magnetic Stripe Reader
To use the Magnetic Stripe Reader, insert the
card into the reader slot located on the top of
the Q20. The terminal reads the information
from the card when the magnetic stripe is
inserted into the card slot.
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. The Bluetooth® word mark
and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by PAX Technology, Inc. is under
license. Other trademarks and trade names are those of their
respective owners.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us

P/N:200312000000426
E800
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Light Sensor
Printer CoverOpening
Advance Paper
Q20
SIM Card/SD Card Cover USB Port
Main Display
Printer Paper Exit
Printer Cover
Open Printer Cover
Printer Indicators:
Power
Out of Paper
Printer Error
Main Display Guest Display
Loudspeaker
Heat Emission Holes
Back Cover
Magnetic Stripe
Card/IC Card Slot
Contactless Reader
Scanning Camera
Guest Display
WAN
LAN x 2
USB x 4
Micro USB
Micro SD Card Slot
USB Port
Audio Jack
Power Port Back Cover
Serial Port
Cash Drawer Interface
The following ports are accessible on the side of the E800:
· Micro SD Card Slot – Open card cover and insert card into TF slot
· SIM Card Slot – Open card cover and insert SIM card into SIM slot to
connect to cellular carrier’s network
· USB – Connect USB device without opening back cover
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Power Button
Terminal Ports
Open the back cover to access the following ports:
·Power – Connect AC power supply to E800
·Audio Jack – Allows hearing impaired to connect assistive listening
device
·Cash Drawer – Insert the cable from cash drawer to connect with
cash register
·WAN – Insert cable connected to the Internet to provide wired network
for cash register
·LAN – Used for bi-directional Ethernet connections
·RS232 – Used to connect to serial device such an external POS
device or check reader
·Micro USB – Connect Micro USB device
·USB-OTG – Used for local terminal downloads or external peripherals
·USB – Connect USB device
Power ON/OFF
1. Power on: Press and hold the Power button (on the side) for three
seconds until the main screen displays normally. (See page 2 for the
location of the Power button.
2. Power off: Press and hold the Power button (on the side) for three
seconds until the shutdown menu displays. Select Power off. The
terminal turns off after a few seconds. (See page 2 for the location of
the Power button.)
Hybrid Card Reader
5
The Q20 on the consumer-facing side of the
E800 includes a reader that can be used as a
Magnetic Stripe, EMV, and NFC/Contactless
card reader.
Magnetic Stripe Reader
To use the Magnetic Stripe Reader, insert the
card into the reader slot located on the top of
the Q20. The terminal reads the information
from the card when the magnetic stripe is
inserted into the card slot.
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. The Bluetooth® word mark
and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by PAX Technology, Inc. is under
license. Other trademarks and trade names are those of their
respective owners.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us

1.When the printer is out of paper,
the yellow "Paper Out" indicator
lights. Open the external printer
cover by inserting your finger into
a recessed area to the side of the
door and pulling outward.
E800
Integrated Smart Terminal
Load Printer Paper
2. Open the built-in printer cover by
pressing in the latch, as shown.
The printer door will slowly open.
3. Load the paper roll, as shown.
Extend the end of the paper roll
out of the printer.
4. Press both sides of the built-in
printer cover until it snaps closed.
Close the external printer cover.
The Paper Out indicator light turns
off.
Avoid exposing the device to an excessively hot, humid, dusty, or
strong electromagnetic environment.
·Do not vibrate, shake, or drop the device.
·Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
·Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
tooperate the equipment. In a domestic environment, this product may
cause radio interference in which case the user may be required
to take adequate measures.
Peripheral Ports: Micro-USB port x 1
USB ports x 5
Network ports x 3 (WAN port x 1, LAN ports x 2)
Cash Drawer x 1
serial port x 1
audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
magnetic stripe card/IC card slot x 1, using
two-in-one（support MAG&ICC）
Magnetic Card Reader: Supports track 1/2/3
IC Card Reader: Conforms to the standard of ISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Operating System: Android 6.0
CPU: Quad-coreA17,1.8GHZ processor
Memory: 2GB RAM + 16GB Flash Memory
Main Display: 15.6 inch, resolution: 1920*1080, multi-touch
capacitive touch screen
Guest Display: 8 inch, resolution: 1280*800, multi-touch capacitive
touch screen
Printer: 3" high-speed thermal printer with auto-cutter,
printing speed:150mm/s
Audio: supports headphone output
Camera: 5 mega-pixel auto-focusing camera, high-speed
EMV Card Reader
To use the EMV Card Reader, insert the card with the front facing you and
the chip down into the card slot. Leave the card inserted until the terminal
prompts to remove the card.
NFC/Contactless Card Reader
To use the NFC/Contactless Reader, tap the card to the Q20 screen when
prompted. The terminal uses an antenna device that detects and retrieves
information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
code scanning
L-Sensor (Ambient Light Sensor): automatically adjusts the backl
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth®
wireless technology , 3G/4G(optional)
ight

1.When the printer is out of paper,
the yellow "Paper Out" indicator
lights. Open the external printer
cover by inserting your finger into
a recessed area to the side of the
door and pulling outward.
E800
Integrated Smart Terminal
Load Printer Paper
2. Open the built-in printer cover by
pressing in the latch, as shown.
The printer door will slowly open.
3. Load the paper roll, as shown.
Extend the end of the paper roll
out of the printer.
4. Press both sides of the built-in
printer cover until it snaps closed.
Close the external printer cover.
The Paper Out indicator light turns
off.
Avoid exposing the device to an excessively hot, humid, dusty, or
strong electromagnetic environment.
·Do not vibrate, shake, or drop the device.
·Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
·Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
tooperate the equipment. In a domestic environment, this product may
cause radio interference in which case the user may be required
to take adequate measures.
Peripheral Ports: Micro-USB port x 1
USB ports x 5
Network ports x 3 (WAN port x 1, LAN ports x 2)
Cash Drawer x 1
serial port x 1
audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
magnetic stripe card/IC card slot x 1, using
two-in-one（support MAG&ICC）
Magnetic Card Reader: Supports track 1/2/3
IC Card Reader: Conforms to the standard of ISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Operating System: Android 6.0
CPU: Quad-coreA17,1.8GHZ processor
Memory: 2GB RAM + 16GB Flash Memory
Main Display: 15.6 inch, resolution: 1920*1080, multi-touch
capacitive touch screen
Guest Display: 8 inch, resolution: 1280*800, multi-touch capacitive
touch screen
Printer: 3" high-speed thermal printer with auto-cutter,
printing speed:150mm/s
Audio: supports headphone output
Camera: 5 mega-pixel auto-focusing camera, high-speed
EMV Card Reader
To use the EMV Card Reader, insert the card with the front facing you and
the chip down into the card slot. Leave the card inserted until the terminal
prompts to remove the card.
NFC/Contactless Card Reader
To use the NFC/Contactless Reader, tap the card to the Q20 screen when
prompted. The terminal uses an antenna device that detects and retrieves
information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
code scanning
L-Sensor (Ambient Light Sensor): automatically adjusts the backl
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth®
wireless technology , 3G/4G(optional)
ight

1.When the printer is out of paper,
the yellow "Paper Out" indicator
lights. Open the external printer
cover by inserting your finger into
a recessed area to the side of the
door and pulling outward.
E800
Integrated Smart Terminal
Load Printer Paper
2. Open the built-in printer cover by
pressing in the latch, as shown.
The printer door will slowly open.
3. Load the paper roll, as shown.
Extend the end of the paper roll
out of the printer.
4. Press both sides of the built-in
printer cover until it snaps closed.
Close the external printer cover.
The Paper Out indicator light turns
off.
Avoid exposing the device to an excessively hot, humid, dusty, or
strong electromagnetic environment.
·Do not vibrate, shake, or drop the device.
·Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
·Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
tooperate the equipment. In a domestic environment, this product may
cause radio interference in which case the user may be required
to take adequate measures.
Peripheral Ports: Micro-USB port x 1
USB ports x 5
Network ports x 3 (WAN port x 1, LAN ports x 2)
Cash Drawer x 1
serial port x 1
audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
magnetic stripe card/IC card slot x 1, using
two-in-one（support MAG&ICC）
Magnetic Card Reader: Supports track 1/2/3
IC Card Reader: Conforms to the standard of ISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Operating System: Android 6.0
CPU: Quad-coreA17,1.8GHZ processor
Memory: 2GB RAM + 16GB Flash Memory
Main Display: 15.6 inch, resolution: 1920*1080, multi-touch
capacitive touch screen
Guest Display: 8 inch, resolution: 1280*800, multi-touch capacitive
touch screen
Printer: 3" high-speed thermal printer with auto-cutter,
printing speed:150mm/s
Audio: supports headphone output
Camera: 5 mega-pixel auto-focusing camera, high-speed
EMV Card Reader
To use the EMV Card Reader, insert the card with the front facing you and
the chip down into the card slot. Leave the card inserted until the terminal
prompts to remove the card.
NFC/Contactless Card Reader
To use the NFC/Contactless Reader, tap the card to the Q20 screen when
prompted. The terminal uses an antenna device that detects and retrieves
information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
code scanning
L-Sensor (Ambient Light Sensor): automatically adjusts the backl
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth®
wireless technology , 3G/4G(optional)
ight

1.When the printer is out of paper,
the yellow "Paper Out" indicator
lights. Open the external printer
cover by inserting your finger into
a recessed area to the side of the
door and pulling outward.
E800
Integrated Smart Terminal
Load Printer Paper
2. Open the built-in printer cover by
pressing in the latch, as shown.
The printer door will slowly open.
3. Load the paper roll, as shown.
Extend the end of the paper roll
out of the printer.
4. Press both sides of the built-in
printer cover until it snaps closed.
Close the external printer cover.
The Paper Out indicator light turns
off.
Avoid exposing the device to an excessively hot, humid, dusty, or
strong electromagnetic environment.
·Do not vibrate, shake, or drop the device.
·Do not plug or unplug any part of the device while it is powered on.
This may cause damage to an internal circuit.
·Please contact PAX technical support for assistance with the device.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
tooperate the equipment. In a domestic environment, this product may
cause radio interference in which case the user may be required
to take adequate measures.
Peripheral Ports: Micro-USB port x 1
USB ports x 5
Network ports x 3 (WAN port x 1, LAN ports x 2)
Cash Drawer x 1
serial port x 1
audio jack x 1
Card Slot: SIM card slot x 1
Micro SD card slot x 1
magnetic stripe card/IC card slot x 1, using
two-in-one（support MAG&ICC）
Magnetic Card Reader: Supports track 1/2/3
IC Card Reader: Conforms to the standard of ISO7816,
EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Operating System: Android 6.0
CPU: Quad-coreA17,1.8GHZ processor
Memory: 2GB RAM + 16GB Flash Memory
Main Display: 15.6 inch, resolution: 1920*1080, multi-touch
capacitive touch screen
Guest Display: 8 inch, resolution: 1280*800, multi-touch capacitive
touch screen
Printer: 3" high-speed thermal printer with auto-cutter,
printing speed:150mm/s
Audio: supports headphone output
Camera: 5 mega-pixel auto-focusing camera, high-speed
EMV Card Reader
To use the EMV Card Reader, insert the card with the front facing you and
the chip down into the card slot. Leave the card inserted until the terminal
prompts to remove the card.
NFC/Contactless Card Reader
To use the NFC/Contactless Reader, tap the card to the Q20 screen when
prompted. The terminal uses an antenna device that detects and retrieves
information from the card.
Specifications
7
Installation and Usage Tips
Note: Product images shown may be different than actual product
received
PAX TECHNOLOGY INC.
Quick Setup Guide
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
8
code scanning
L-Sensor (Ambient Light Sensor): automatically adjusts the backl
brightness of the main display
Wireless Communication: Supports LAN, WIFI, Bluetooth®
wireless technology , 3G/4G(optional)
ight

P/N:200312000000426
E800
AC Power Adapter
Quick Setup Guide
AC Power Cable
Thermal Paper Roll
Light Sensor
Printer CoverOpening
Advance Paper
Q20
SIM Card/SD Card Cover USB Port
Main Display
Printer Paper Exit
Printer Cover
Open Printer Cover
Printer Indicators:
Power
Out of Paper
Printer Error
Main Display Guest Display
Loudspeaker
Heat Emission Holes
Back Cover
Magnetic Stripe
Card/IC Card Slot
Contactless Reader
Scanning Camera
Guest Display
WAN
LAN x 2
USB x 4
Micro USB
Micro SD Card Slot
USB Port
Audio Jack
Power Port Back Cover
Serial Port
Cash Drawer Interface
The following ports are accessible on the side of the E800:
· Micro SD Card Slot – Open card cover and insert card into TF slot
· SIM Card Slot – Open card cover and insert SIM card into SIM slot to
connect to cellular carrier’s network
· USB – Connect USB device without opening back cover
Please check the components after unpacking. If any are missing,
please contact the dealer.
Part
Power Button
Terminal Ports
Open the back cover to access the following ports:
·Power – Connect AC power supply to E800
·Audio Jack – Allows hearing impaired to connect assistive listening
device
·Cash Drawer – Insert the cable from cash drawer to connect with
cash register
·WAN – Insert cable connected to the Internet to provide wired network
for cash register
·LAN – Used for bi-directional Ethernet connections
·RS232 – Used to connect to serial device such an external POS
device or check reader
·Micro USB – Connect Micro USB device
·USB-OTG – Used for local terminal downloads or external peripherals
·USB – Connect USB device
Power ON/OFF
1. Power on: Press and hold the Power button (on the side) for three
seconds until the main screen displays normally. (See page 2 for the
location of the Power button.
2. Power off: Press and hold the Power button (on the side) for three
seconds until the shutdown menu displays. Select Power off. The
terminal turns off after a few seconds. (See page 2 for the location of
the Power button.)
Hybrid Card Reader
5
The Q20 on the consumer-facing side of the
E800 includes a reader that can be used as a
Magnetic Stripe, EMV, and NFC/Contactless
card reader.
Magnetic Stripe Reader
To use the Magnetic Stripe Reader, insert the
card into the reader slot located on the top of
the Q20. The terminal reads the information
from the card when the magnetic stripe is
inserted into the card slot.
PAX TECHNOLOGY INC.
PAX TECHNOLOGY INC.
This document is provided to you for informational purposes
only. All features and specifications are subject to change
without notice. PAX’s name and PAX’s logo are registered
trademarks of PAX Technology Inc. The Bluetooth® word mark
and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by PAX Technology, Inc. is under
license. Other trademarks and trade names are those of their
respective owners.
Responsible Party:
PAX Technology, Inc.
8880 Freedom Crossing Trail
Building 400, 3rd Floor, Suite 300
Jacksonville, FL 32256, USA
Help Desk
1-877-859-0099
www.pax.us