peerless-AV HLG440-PH Guide

1 of 4 ISSUED: 10-30-10 SHEET #:125-9164-2 09-14-11
Model: HLG440-PH, HLG440-PH-Q10
Installation and Assembly:
Desktop Swivel Mount for Philips 32HFL2082 and 40HFL2082 Displays
A
B C
D E
NOTE: Read entire instruction sheet before you start installation and assembly.
Before you start make sure all parts listed are included with your product.
F
H I
Mounting to Desktop Surface
Mounting using Bolt Down Method
G
HLG440-PH HLG440-PH-Q10
Description Qty Part # Qty Part #
A
swivel plate assembly 1 090-1983 10 090-1983
B10-32 x 3/8 flat head self drilling screw 3 560-2743 30 560-2743
C1/4-20 x 1-3/4" thin head carriage bolt 2 560-1764 20 560-1764
D1/4-20 slope nut 3 530-0035 23 530-0035
Eplastic cap 2 590-1294 20 590-1294
F4 mm allen wrench 1 560-9646 3 560-9646
GM5 x 20 mm socket pin screw 2 520-1065 20 520-1065
H#10 split lock washer 2 540-1035 20 540-1035
I#10 flat washer 2 540-9400 20 540-9400
Parts List

2 of 4 ISSUED: 10-30-10 SHEET #:125-9164-2 09-14-11
LEFT SIDE
Use swivel plate assembly (A) as a template to mark location of holes, point 1 and point 2, approximately 3" apart
on table. Drill two holes using a 1/4'' drill bit.
Place two 1/4-20 x 1-3/4" thin head carriage bolts (C) into slots of swivel plate assembly (A).
2
POINT 1 POINT 2
TABLE TOP
3"
1
C
Choose swivel range below and identify swivel range holes of swivel plate assembly (A).
SWIVEL RANGE HOLE
Mounting using Bolt Down Method
90°
60°
A
60°
90°
30° 30°
FRONT
FRONT
A
(76 mm)
USE HOLES TO LOCK SWIVEL
PLATE ASSEMBLY 90° FROM
CENTER
RIGHT SIDE

3 of 4 ISSUED: 10-30-10 SHEET #:125-9164-2 09-14-11
Hand tighten slope nut (D) through 1/4-20 x 1-3/4" thin head carriage bolt (C) until snug against bottom of desktop
surface. Thread another slope nut (D) upside-down, about two turns from rst slope nut (D). Insert an open box
wrench between both slope nuts (D) and tighten. NOTE: Avoid jamming both slope nuts (D) together, doing so
may make it difcult to remove slope nut used for tightening rst slope nut (D) as shown in g 4.1. After slope nut is
secure remove bottom slope nut and add plastic cap (E) as shown in gure 4.2. Repeat with remaining
1/4-20 x 1-3/4" thin head carriage bolt (C).
Detail 1
TIGHTENING
SLOPE NUT
3
B
32" Display Base Attachment Location
(note orientation of plate to base)
BOTTOM OF DESKTOP
FIG 4.1 FIG 4.2
C
D
C
4
E
Secure swivel plate assembly (A) to bottom of display base using three 10-32 x 3/8" at head self drilling screws (B)
in 32" or 42" orientation.
NOTE: Make sure that screws in display base align with slots and holes in swivel plate assembly (A)
as shown below.
FRONT
NOTE: Do not overtighten slope nut (D)
plate may distort
42" Display Base Attachment Location
(note orientation of plate to base)
A
ARROW INDICATES FRONT OF SWIVEL
PLATE ASSEMBLY
.88"
C
D
FRONT
DISPLAY
BASE SCREWS
DISPLAY
BASE SCREWS

4 of 4 ISSUED: 10-30-10 SHEET #:125-9164-2 09-14-11
5
DISPLAY
DISPLAY BASE
NOTE: Display and base may appear
different than illustrated
Installation of Security Screws for Base to Display Attachment
G
I
32" Display Base (No Screws Required)
Attach display to base using hardware provided with display using the manufactures installation manual.
42" Display Base
Attach display to base using two M5 x 20 mm socket pin screws (G), two #10 split lock washers (H), and two
#10 at washers (I) into bottom holes as shown below. Tighten with 4 mm security allen wrench (F).
Use screws supplied with display for remaining holes.
© 2010, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
42" Display Base Attachment Location
(note orientation of screws)
H