Petsafe Stubborn Dog In Ground Fence RF-275-11 User manual

stubborn dog
in-ground fence™
receiver collar / collier-récepteur / collar receptor
operating guide /guide d’emploi /guía para el uso
RF-275-11
PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING.
VEUILLEZ LIRE L’INTÉGRALITÉ DE CE MANUEL AVANT TOUTE UTILISATION.
SÍRVASE LEER COMPLETAMENTE ESTA GUÍA ANTES DE COMENZAR A USAR EL PRODUCTO.

2 1-800-732-2677
Important Safety Information
Explanation of Attention Words and Symbols used in this guide
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION, used without the safety alert symbol, indicates
a hazardous situation which, if not avoided, could result in
harm to your pet.
• Not for use with aggressive dogs. Do not use this product
if your dog is prone to aggressive behavior. Aggressive
dogs can cause severe injury or death to their owners and
others. If you are not sure that this product is right for your
dog, please talk to your veterinarian or a certified trainer.

www.petsafe.net 3
This PetSafe®Stubborn Dog In-Ground Fence™is not a
solid barrier. This system is designed to act as a deterrent to
remind pets by Static Correction to remain in the boundary
established. It is important that you reinforce training with your
pet on a regular basis. Proper fit of the collar is important.
A collar worn for too long or made too tight on the pet’s neck
may cause skin damage. Ranging from redness to pressure
ulcers; this condition is commonly known as bed sores.
• Avoid leaving the collar on the dog for more than 12 hours
per day.
• When possible reposition the collar on the pet’s neck every
1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the
instructions in this manual.
• Never connect a lead to the electronic collar; it will cause
excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure
on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar
weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.

4 1-800-732-2677
• If a rash or sore is found, discontinue use of the collar
until the skin has healed.
• If the condition persists beyond 48 hours, see your
veterinarian.
• For additional information on bed sores and pressure
necrosis, please visit our website.
These steps will help keep your pet safe and comfortable.
Millions of pets are comfortable while they wear stainless
steel contacts. Some pets are sensitive to contact pressure.
You may find after some time that your pet is very tolerant
of the collar. If so, you may relax some of these precautions.
It is important to continue daily checks of the contact area.
If redness or sores are found, discontinue use until the skin
has fully healed.
You may need to trim the hair in the area of the Contact
Points. Never shave the dog’s neck; this may lead to a rash
or infection.
• The Receiver Collar should not be on your dog when the
system is tested. Your pet may receive an unintended
correction.

www.petsafe.net 5
• The Boundary Width of the system must be tested
whenever an adjustment is made to the containment field
to prevent unintended corrections to your pet.
• If you use a collar and leash for training, be sure the extra
collar does not put pressure on the contact points.
• Always remove your dog’s Receiver Collar before
performing any Transmitter testing.
• If possible, DO NOT use an AC circuit protected with a
Ground Fault Circuit Interrupter (GFCI) or Residual Current
Device (RCD). In rare cases, nearby lightning strikes may
cause the GFCI or RCD to trip. Without power your dog
may be vulnerable to escape. You will have to reset the
GFCI or RCD to restore power to the system.

6 1-800-732-2677
Thank you for choosing PetSafe®brand. You and your pet
deserve a companionship that includes memorable moments
and a shared understanding together. Our products and
training tools promote a lifestyle of protection, teaching, and
love — essentials that influence memories for a lifetime. If you
have any questions about our products or training your pet,
please visit our website at www.petsafe.net or contact our
Customer Care Center at 1-800-732-2677.
To get the most protection out of your warranty, please register
your product within 30 days at www.petsafe.net. By registering
and keeping your receipt, you will enjoy the product’s full
warranty and should you ever need to call the Customer Care
Center, we will be able to help you faster. Most importantly,
PetSafe®will never give or sell your valuable information to
anyone. Complete warranty information is available online at
www.petsafe.net.
Fence installation and training help: www.petsafe.net.

www.petsafe.net 7
How the System Works
A radio signal travels from the Fence Transmitter through a buried
wire, marking the boundaries you wish to set for your dog. Your dog
wears a Receiver Collar that detects the signal at the boundary. As
your dog approaches the boundary, the receiver issues a warning tone
and vibrates. If he proceeds further, he receives a safe but startling
Static Correction. While harmless, the correction will persuade him
to stay in the containment area you’ve established. Boundary flags
are a temporary visual aid for your pet; remove them after training.
This PetSafe®Stubborn Dog In-Ground Fence™has been proven safe,
comfortable, and effective for pets over 8 pounds.

8 1-800-732-2677
Operating Guide
Prepare the Receiver Collar
Your Receiver Collar comes with short Contact
Points installed. Use the long Contact Points for
pets with long or thick hair. Tighten the Contact
Points using Test Light Tool (A) one-half turn
beyond finger tight. Check the tightness weekly.
A
To Insert and Remove
the Battery
Note: Do not install the battery while
the Receiver Collar is on your pet.
1. Remove the screws with a Phillips
screwdriver.
2. Remove the Battery lid (B).
BC

www.petsafe.net 9
3. Install a 9-volt alkaline battery (C).
4. Replace the Battery Lid (C).
5. Reinstall the screws. Do not over-tighten the screws.
If the Receiver Indicator Light is flashing every 4 to 5 seconds, battery
replacement is required. Remove the old battery from the Receiver
Collar. Discharge all power by holding the correction level button down
until the light is no longer illuminated. Replace with a new battery.
Be sure to discard the used battery properly.
A replacement 9-volt alkaline battery (PAC11-12067) can be found at
many retailers. Contact the Customer Care Center or visit our web site
at www.petsafe.net to locate a retailer near you.

10 1-800-732-2677
To Set the Static Correction Level
Read all steps before attempting to set the Static Correction Level.
1. Remove the clear plastic cover with the Test Light
Tool to expose the Correction Level Button (D).
2. With the battery installed, press the Correction
Level Button and release when the Receiver
Indicator Light lights up (E).
3. The Receiver Indicator Light will emit a series of
flashes representing the Static Correction Level.
4. Increase the Static Correction Level by pressing
and releasing the Correction Level Button within
5 seconds of the previous series of flashes.
5. After setting the Static Correction Level, replace
the cover to protect the Correction Level Button.
The Static Correction levels increase in strength
from 1 to 5. Pushing the Correction Level Button
while the Receiver Collar is on level 5 will cause
the Receiver Collar to revert to Level 1. Refer to
the Function and Response Table to choose the
Static Correction level that best fits your pet. The
Receiver Collar will emit a Warning Tone and vibrate
D
E

www.petsafe.net 11
whenever your pet enters the Warning Zone, no matter what the
correction level the Receiver Collar is set to. If your pet continues into the
Correction Zone, and the Receiver Collar is set to level 2 or above, he will
receive a Static Correcton.
The Receiver Collar is equipped to automatically increase the level of
Static Correction the longer your pet remains in the Static Correction
Zone if the collar is set at level 2 or above.
The Receiver Indicator Light acts as a low battery indicator, flashing every
4 to 5 seconds when replacement is required. Test your Receiver Collar
at least once a month to verify that it is functioning properly and that it
activates at the Boundary Wire.
Over Correction Protection
In the unlikely event that your pet “freezes” in the Static Correction Zone,
this feature limits the static correction duration to a maximum of 30
seconds. While the system locks out further static correction, the warning
tone will continue until the pet leaves the Static Correction Zone.

12 1-800-732-2677
Function and Response Table
Indicator Light
Response
Static Correction
Level
Receiver Collar
Function Temperament of Pet
1 Flash 1
No Static
Correction,
Tone Plus
Vibration
Initial Training
Mode
2 Flashes 2Low Static
Correction Timid
3 Flashes 3Medium Static
Correction Timid or Average
4 Flashes 4Medium High Static
Correction
Average or
High Energy
5 Flashes 5High Static
Correction High Energy
Flashes
once every
4 to 5 seconds
Indicates Low
Battery

www.petsafe.net 13
Fit the Receiver Collar
Important: The proper fit and placement of your Receiver Collar is
important for effective training. The Contact Points must have direct
contact with your pet’s skin on the underside of his neck. See important
safety information on pages 3-5.
To assure a proper fit, please follow these steps:
1. Make sure that the battery is not installed in
the Receiver Collar.
2. Start with your pet standing comfortably (F).
3. Place the Receiver Collar on your pet so that
the “PetSafe” logo is facing your pet’s chin.
Center the Contact Points underneath your
pet’s neck, touching the skin.
F

14 1-800-732-2677
4. The Receiver Collar should fit
snugly, yet loose enough to
allow one finger to fit between a
contact point and your pet’s neck
(G). Allow your pet to wear the
collar for several minutes then
recheck the fit. Check the fit
again as your pet becomes more
comfortable with the Receiver
Collar.
5. Once you are satisfied with the
fit of the Receiver Collar then you
may trim any excess collar strap
as follows (H):
a. Mark the desired length of
G
H
the Receiver Collar with a pen. Allow for growth if your pet is
young or grows a thick winter coat.
b. Remove the Receiver Collar from your pet and cut off the excess.
c. Before placing the Receiver Collar back onto your pet, seal the
edge of the cut collar by applying a flame along the frayed edge.

www.petsafe.net 15
To Re-Thread the Collar
Slide Buckle
Ridges
The slide buckle prevents the
collar from becoming loose
around your pet’s neck.
The ridges must be facing
up; the collar will slip if it is
not properly threaded.

16 1-800-732-2677
Taking Your Pet Out of the Pet Area
Important: Remove the Receiver Collar and leave it in the Pet Area.
Once your pet learns the Boundary Zone, he will
be reluctant to cross it for walks or car rides.
Option 1: Replace the Receiver Collar with a
regular collar. Put your pet in a car that is within
the Pet Area and drive him out of the Pet Area.
Option 2: Replace the Receiver Collar with a
regular collar and leash. Walk your pet out of the
Pet Area while giving a command such as “OK”
at a specific place of the Boundary Zone (the end
of your driveway, sidewalk, etc.). Always leave the
Pet Area with a leash at this place and your pet
will associate leaving the Pet Area only on a leash, only at this place, and
only with a person. You may initially need to convince your pet to leave
the Pet Area with a food treat and lots of praise.
Note: You may also carry your pet out of the Pet Area.

www.petsafe.net 17
Please refer to your PetSafe®In-Ground Fence™Operating and Training
Guide for a complete list of Troubleshooting or visit www.petsafe.net.
Troubleshooting
Receiver Collar
is not beeping or
correcting.
• Check battery to make sure it is installed properly.
• Check that both lights are lit on the Fence
Transmitter. Refer to Stubborn Dog In-Ground
Fence™Operating and Training Guide.
The Receiver
Collar is beeping,
but the pet is not
responding to the
Static Correction.
• Test the Receiver Collar with the Test Light walking
toward the Boundary Wire.
• If the Test Light flashes, check the fit of the Receiver
Collar.
• Trim your pet’s fur where the Contact Points touch
the neck and/or switch to the longer Contact Points.
• Increase the Static Correction Level.
• Repeat training steps to reinforce training.

18 1-800-732-2677
The Receiver Collar
has to be held on
top of the Boundary
Wire to activate.
• Replace battery.
• Adjust Boundary Width Control knob clockwise to
increase the distance from the Boundary Wire that
the Receiver Collar activates. Verify the Boundary
Control Switch is placed at the proper setting
according to the amount of Boundary Wire used.
• If the Receiver Collar still has to be held on top
of the Boundary Wire, refer to Stubborn Dog
In-Ground Fence™Operating and Training Guide.
The Receiver Collar
activates inside the
house.
• Turn the Boundary Width Control knob
counterclockwise to decrease the distance from the
Boundary Wire that the Receiver Collar activates.
• Make sure the Boundary Wire is not running within
15 feet of the house. The signal can transmit through
the walls of your house.
• Make sure Boundary Wires are twisted from
Boundary to the Fence Transmitter.
The Receiver
Indicator Light is
flashing every 4 to 5
seconds and I have
just installed a new
battery.
• To reset the low battery indicator, remove the
battery from the Receiver Collar. Discharge all power
by holding the correction level button down until the
light is no longer illuminated. Reinstall battery.

www.petsafe.net 19
Additional Information
• The system should only be used with healthy pets. Contact your
veterinarian if you have concerns about the medical condition of your
pet (medication, pregnant, heart conditions, etc.).
• The PetSafe®Stubborn Dog In-Ground Fence™is for residential use only.
• The Static Correction will get your pet’s attention, but will not cause
harm. It is designed to startle, not to punish.
• Test the Receiver Collar at least once a month to verify that it is
functioning properly. Check that it activates at the Boundary Wire.
Battery life depends upon how often the Receiver Collar is activated.
• Remove the Receiver collar from your pet when indoors for the comfort
of your pet.
• Never leave the Receiver Collar on your pet for more than
12 consecutive hours.

20 1-800-732-2677
Test Light Instructions
1. Make sure the Receiver Collar battery
is properly installed. Set the Correction
Level to 2 or above.
2. Hold the Test Light Contacts to the
Contact Points (I).
3. Walk toward the Boundary Wire with
Contact Points pointing up and holding
the Receiver Collar at your pet’s neck level
(J) until the Receiver Collar tones and the
I
Test Light flashes (K). J
B
o
u
n
d
a
r
y
Z
o
n
e
Pet
Area
K