Philips CID3692/00 User manual

www.philips.com/welcome
Register your product and get support at CID3692
EN Quick Start Guide

1
5DGLRDQWHQQD
*36DQWHQQD
2SWLRQDO
Amplifier
൰ၿࠓใཐ
ޮ෿Ԭଇ௤
%ODFN
ᇛֲၿൿԟ
ޮႻၿ௘ൿԟ
ޮቔၿ௘ൿԟ
ఱႻၿ௘ൿԟ
ఱቔၿ௘ൿԟ
$8;
$9V\VWHP
:LUHOHVVKHDGSKRQH
5HDUVFUHHQ
:KLWH
<HOORZ
ڧᇽ൮௘ൿೊ
ڧᇽቔၿ௘ൿೊ ڧᇽႻၿ௘ൿೊ
ޮ෿൮௘ൿԟ
ޮ෿൮௘ൿԟ
ޮ෿ቔၿ௘ൿԟ
:KLWH
5HG
<HOORZ
:KLWH
5HG
5HG
:KLWH
5HG
%URZQ
5$',2$17
86%
AUX IN VIDEO
AUX IN L
AUX IN R
SUB. W
REAR R
REAR L
FRONT R
FRONT L
REAR VIDEO OUT 1
REAR OUT/R REAR OUT/L
<HOORZ *UHHQ
CAMERA
BRAKE
REVERSE
P.CONT
CMMB BUS
MZ-TFT
ޮ൮ࣨ܆׌ֽཐ
&$0(5$*1'
ޮ൮ࣨ൮௘ൿೊ
&$0(5$9,'(2
%ODFN
<HOORZ
%OXH:KLWH
3LQN5HG
*UHHQ:KLWH
Gearbox
೯Ӟࡣҭ
֞Ӟࡣҭ
܃٦ᇉ

2
a
b

3
4
5

English
Connect wires 1
1Check the car’s wirings carefully, then
connect them to the unit.
Mount in the dashboard 2
1If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
2Ensure that the horizontal slant of the car
dashboard opening is between 0 and 20
degrees. The unit cannot be used if the
dashboard opening’s slant angle is above 20
degrees.
3Fix the mounting brackets to the unit with
screws (supplied by the car manufacturer). a
4 Slidetheunitintothedashboardandxitto
the car with four screws. b
5Reconnect the negative terminal of the car
battery.
Turn on
1Press and hold /MUTE/VOL to turn on
the unit.
The available OSD (On-Screen Display)»
languages are displayed.
2Tap a language to select.
To turn off the unit, press and hold• /
MUTE/VOL.
Set date and time
1Tap the upper left corner to display the
main menu.
2Tap in the middle right side of the screen.
3Tap [Settings].
4Tap [Time].
T»he date/time setup menu is displayed.
Set date
1Tap [Date].
2Tap on the displayed date information.
3Tap or to set year, month and day.
Set clock mode
1Tap [Clock mode] .
2Tap on [12Hr] or [24Hr] to select clock
mode.
Set time
1Tap [Time].
2Tap on the displayed time.
3Tap or to set hour and minute.
Use map
Note
You may need to upgrade the map (sold•
separately) before using it.