Pine Crafter Furniture 072 User manual

072 – 072F - 472 – 472F
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE THIS BED
MATTRESS SIZES…
Bed Mattresses Specifications:
Use only a mattress meeting the following specifications on the upper bunk bed.
Bed Type Width Length Bed Type Width Length
Standard Twin 37½”-38½” 74”-75” XL Twin 37½”-38½” 79”-80”
Standard Full 52½”-53½” 74”-75” XL Full 52½”-53½” 79”-80”
Total thickness of both mattress and foundation MUST NOT EXCEED 6½” for upper bunk.
SAFETY WARNINGS AND GENERAL NOTES
Follow information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
or entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guard rails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guard rails on both sides of the upper bunk.
The use of water or sleep floatation mattresses is prohibited.
Prohibit more than one person on the upper bunk.
Keep these instructions for future references.
We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet. Be
certain all staples are out of the box before beginning assembly on the shipping carton.
Strangulation Hazard - Never attach or hang items to any part of the bunk bed that are not designed
for use with the bed; for example, but not limited to, hooks, belts and jump ropes.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be obtained from any of our Pine Crafter
dealers.Hardware – (Actual Size not Shown)
Hex Key
#072=2
#072F=2
#472=2
#472F=2
30mm Bed
Bolt and
Cap Nut
#072=16
#072F=16
#472=16
#472F=16
70mm Lag
Bolt Screw
#072=8
#072F=8
#472=8
#472F=8
Caster
w/Insert
#072=4
#072F=4
#472=4
#472F=4
L-Bracket
w/3/4” Screw
#072=4
#072F=4
#472=4
#472F=4
Bed Wire and
1” Screw
#072=6
#072F=6
#472=6
#472F=6

072, 072F, 472 & 472F INSTRUCTIONS
#072 & #472 STAIRCASE LOFT BED (6 CARTONS TOTAL)
1 Box (1) Staircase HB
1 Box (1) Twin FB - (Hardware: 8 – 30mm bed bolts, 8 – 17mm cap nuts, 8 – 70mm lag bolt screws,
4 – L-Brackets, 8 ¾” screws & 1 hex key)
1 Box (1) Loft Chest
1 Box (2) Twin Bottom HB/FB - (Hardware: 8 – 30mm bed bolts, 8 – 17mm cap nuts, 4 – casters
w/inserts & 1 hex key)
1 Box (4) Twin Top Rails - (Hardware: 3 – twin bed wires & 6 bed wire screws)
1 Box (2) Twin Bottom Rails - (Hardware: 3 – twin bed wires & 6 – bed wire screws)
#072F & #472F STAIRCASE LOFT BED (6 CARTONS TOTAL)
1 Box (1) Staircase HB
1 Box (1) Twin FB - (Hardware: 8 – 30mm bed bolts, 8 – 17mm cap nuts, 8 – 70mm lag bolt screws,
4 – L-Brackets, 8 ¾” screws & 1 hex key)
1 Box (1) Loft Chest
1 Box (2) Full Bottom HB/FB - - (Hardware: 8 – 30mm bed bolts, 8 – 17mm cap nuts, 4 – casters
w/inserts & 1 hex key)
1 Box (4) Twin Top Rails - (Hardware: 3 – twin bed wires & 6 bed wire screws)
1 Box (2) Full Bottom Rails - (Hardware: 3 – full bed wires & 6 – bed wire screws)
TOOLS REQUIRED
Hex Key (provided)
Phillips Screwdriver or Electric Drill
ASSEMBLY INSTRUCTIONS
1. Check cartons to be sure all wooden parts and hardware is included.
2. Obtain one box of staircase HB and one box of loft chest. Stand staircase HB and loft chest
upright.
3. Obtain one box of twin FB and one box of (4) twin top rails and insert 30mm bed bolts
through metal bracket on cleated rail and middle set holes on staircase HB, as shown in Figure 1.
Secure with cap nut but do not fully tighten.
4. Repeat step 3 for other side.
5. Attach the FB to opposite end using same method as in steps 3 & 4, letting FB rest on
top of loft chest.
6. Attach one guard rail to top set holes of FB by securing 70mm lag bolt screws thru FB holes and
into pre-drilled holes in end of guard rail, as shown in Figure 2.
7. Attach the other end of guard rail to the HB in same manner.
8. Repeat step 6 for other guard rail on opposite side.
9. Now, go back and fully tighten all cap nuts and bolts to secure bed.
10. Attach L-Brackets to FB and top of loft chest with provided ¾” screws, as shown in Figure 3.
11. The bed should be positioned approximately ½” back from the ends and edges as shown in
Figure 4. Do not leave the upper bunk unattached. Even if it isn’t used as a sleeping area it may
be dislodged and fall resulting in serious injury or death.
12. Obtain one box of (2) twin or full bottom HB/FB and one box of (2) twin or full bottom
rails and insert 30mm bed bolts through metal bracket on cleated rail and holes on
HB/FB, as shown in Figure 5. Secure with cap nuts.
13. Turn bottom bed upside down and insert knock-in inserts into predrilled holes in the bottom of the
HB/FB.
14. Turn bed upright and roll underneath top loft.
15. Secure bed wires with bed wire screws to top of cleat on cleated rail, as shown in Figure 6.