Pine Crafter Furniture 99 User manual

99 - 99F
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE THIS BED
MATTRESS SIZES…
Bed Mattresses Specifications:
Use only a mattress meeting the following specifications on the upper and lower bunks.
Bed Type Width Length Bed Type Width Length
Standard Twin 37½”-38½” 74”-75” XL Twin 37½”-38½” 79”-80”
Standard Full 52½”-53½” 74”-75” XL Full 52½”-53½” 79”-80”
Total thickness of both mattress and foundation MUST NOT EXCEED 6½” for top and bottom bunks.
SAFETY WARNINGS AND GENERAL NOTES
Follow information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
or entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guard rails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guard rails on both sides of the upper bunk.
The use of water or sleep floatation mattresses is prohibited.
Prohibit more than one person on the upper bunk.
Keep these instructions for future references.
We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet. Be
certain all staples are out of the box before beginning assembly on the shipping carton.
Strangulation Hazard - Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts and jump ropes.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be obtained from any of our Pine Crafter
dealers. Hardware – (Actual Size not Shown)
Hex Key
#99=1
#99F=1
30mm Bed Bolt
#99=8
#99F=8
70mm Lag Bolt
#99=12
#99F=12
3-1/2” Wood Screw
#99=4
#99F=4
Bed Wire
and 1” Screw
#99=3
#99F=3

78, 78F, 99, and 99F INSTRUCTIONS
78, 78F BOX CONTAINERS
1 Box (2) HB/FB - (Hardware: 8 – 30mm bed bolts, 8 cap nuts, 12 – 70mm Lag Bolt and
1 – Hex Key)
1 Box (1) Jr. Ladder - (Hardware: 4 – 3-½” wood screws)
1 Box (1) Jr. Loft Roll-Out Desk
1 Box (1) Jr. Loft Bookcase
1 Box (1) Three Drawer Chest
1 Box (4) Twin Top Rails - (Hardware: 3 – bed wires and 6 – 1” bed wire screws)
1 Box (1) Support Rail
99, 99F BOX CONTAINERS
1 Box (2) HB/FB - (Hardware: 8 – 30mm bed bolts, 8 cap nuts, 12 – 70mm Lag Bolt and
1 – Hex Key)
1 Box (1) Jr. Ladder - (Hardware: 4 – 3-½” wood screws)
1 Box (1) Six Drawer Mini Dresser
1 Box (1) Three Drawer Chest
1 Box (4) Twin Top Rails - (Hardware: 3 – bed wires and 6 – 1” bed wire screws)
1 Box (1) Support Rail
ASSEMBLY TOOLS REQUIRED
Phillips Screwdriver or Electric Drill
Hex Key (Provided)
ASSEMBLY INSTRUCTIONS
1. Check cartons to be sure all wooden parts and hardware is included.
2. To begin assembly, obtain one HB/FB and two cleated rails.
3. Hold the HB/FB upright, insert 30mm bed bolts through metal bracket of cleated rail
and middle set holes on HB/FB and secure with cap nuts as shown in Figure 1.
4. Repeat step 3 for the other side.
5. Attach another HB/FB to the other end using same method as in steps 3 & 4.
6. Obtain one guard rail and assemble to the top set holes in the upper bunk headboard
by securing 70mm lag bolt screws thru HB holes and into pre-drilled holes in end of guard
rail as shown in Figure 2. Repeat this for the other side.
7. Repeat step 6 for other rail.
8. Secure bed wires with bed wire screws to top of cleated rails, as shown in Figure 3.
9. Assemble the bottom support rail by securing 70mm lag bolt screws thru HB/FB holes and
into pre-drilled holes in end of guard rail as shown in Figure 4.
10. Attach ladder to end of bed, as shown in Figure 5.
11. Now slide desk, bookcase, chest and/or dresser underneath bed, as shown in photos
for your model.