Pine Crafter Furniture 4012 User manual

4012 – 4013 – 4013F – 4016 – 4016F – 4019
MC12 – MC13 – MC13F – MC16 – MC16F – MC19
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE THIS BED
MATTRESS SIZES...
Bed Mattresses Specifications:
Use only a mattress meeting the following specifications on the upper and lower bunks.
Bed Type
Width
Length
Bed Type
Width
Length
Standard Twin 37
1
/
2
”-38
1
/
2
” 74”-75” XL Twin 37
1
/
2
”-38
1
/
2
” 79”-80”
Standard Full 52
1
/
2
”-53
1
/
2
” 74”-75” XL Full 52
1
/
2
”-53
1
/
2
” 79”-80”
Total thickness of both mattress and foundation MUST NOT EXCEED 61/2” for top and bottom bunks.
SAFETY WARNINGS AND GENERAL NOTES
Follow information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
or entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guard rails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guard rails on both sides of the upper bunk.
The use of water or sleep floatation mattresses is prohibited.
Prohibit more than one person on the upper bunk.
Keep these instructions for future references.
We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet. Be
certain all staples are out of the box before beginning assembly on the shipping carton.
Strangulation Hazard - Never attach or hang items to any part of the bunk bed that are not designed
for use with the bed; for example, but not limited to, hooks, belts and jump ropes.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be obtained from any of our Pine Crafter dealers.
Hardware – (Actual Size Not Shown)
HexKey 30mm BedBolt
and SilverCap
Nut
70mm
LagBolt Screw
Bed Pins 3 ½” Wood
Screws
Bed Wire
and1” Screws
Wood
Plugs
Each carton will have a white label identifying the item number, contents, carton number and other information.
Manufactured by:
Pine Crafter Furniture
P.O. Box 1100
Haleyville Alabama 35565
Phone: [phone]
Fax: [phone]
Web: www.pinecrafter.com

4012 – 4013 – MC12 – MC13 INSTRUCTIONS
CARTON CONTAINERS
#4012 and #MC12 TWO PIECE TWIN BUNK BED (3 CARTONS TOTAL)
Carton #1: (2) Top HB/FB & (2) Bottom HB/FB - Hardware: (16) 30mm Bed Bolts, (16) Silver Cap Nuts,
(8) 70mm Lag Bolt Screws & (1) Hex Key
Carton #2: (4) Twin Top Rails - Hardware: (3) Twin Bed Wires and (6) 1” Bed Wire Screws
Carton #3: (2) Twin Bottom Rails - Hardware: (3) Twin Bed Wires and (6) 1” Bed Wire Screws
#4013 and #MC13 TWIN STACKABLE BUNK BED (4 CARTONS TOTAL)
Carton #1: (2) Top HB/FB & (2) Bottom HB/FB - Hardware: (4) Metal Pins, (16) 30mm Bed Bolts, (16) Silver
Cap Nuts, (8) 70mm Lag Bolt Screws & (1) Hex Key
Carton #2: (4) Twin Top Rails - Hardware: (3) Twin Bed Wires and (6) 1” Bed Wire Screws
Carton #3: (2) Twin Bottom Rails - Hardware: (3) Twin Bed Wires and (6) 1” Bed Wire Screws
Carton #4: (1) Ladder - Hardware: (4) 3 ½” Wood Screws
TOOLS REQUIRED
Phillips Screwdriver or Electric Drill
Hex Key (Provided)
#4012, #4013, #MC12, #MC13 ASSEMBLY INSTRUCTIONS
1. Check cartons to be sure all wooden parts and hardware is included.
2. To begin assembly, obtain carton #1 (top and bottom HB/FB) and carton #2 (4 twin top rails). NOTE: Bottom
HB/FB has two holes near bottom of each side post. Top HB/FB has four holes near top of each side post.
3. Hold the top HB upright. Insert 30mm bed bolts through bottom set of holes on top HB and metal bracket on
cleated rail as shown in Fig.2. Secure with silver cap nuts but do not fully tighten.
4. Repeat step 3 for other side of HB.
5. Attach the FB to opposite side using same method as in steps 3 and 4.
6. Attach one guard rail to top set of holes of HB by securing 70mm Lag Bolt Screws thru HB holes and into
pre-drilled holes in end of guard rail as shown in Fig.3. Secure but do not fully tighten. Attach the other end
of guardrail to the FB in same manner.
7. Repeat step 6 for other rail on opposite side.
8. Now, go back and fully tighten all cap nuts and bolts to secure bed.
9. Secure bed wires with bed wire screws to both sets of cleated rails as shown in Fig.4.
10. To assemble the bottom bed, obtain carton #1 (top and bottom HB/FB) and carton #3 (2 bottom rails), and
then repeat steps 3 as shown in Fig.1. Then repeat steps 4, 5, 8 & 9.
11. Obtain the metal bed pins and insert into the pre-drilled holes on the top of each side post of the bottom bunk
as shown in Fig.5.
12. You may now stack the bed. Do not leave the upper bunk unattached, even if it isn't used for a sleeping area
it may be dislodged and fall resulting in serious injury or death.
13. For model #4013, obtain carton #4 (ladder) and secure with wood screws as shown in Fig. 6

4013F – 4016 – 4016F – 4019 – MC13F – MC16 – MC16F – MC19 INSTRUCTIONS
CARTON CONTAINERS
#4013F and #MC13F FULL/FULL PANEL BUNK BED (5 CARTONS TOTAL)
Carton #1: (2) Top HB/FB - Hardware: (4) Metal Pins, (8) 30mm Bed Bolts, (8) Silver Cap Nuts, (8) – 70mm
Lag Bolt Screws
Carton #2: (2) Bottom HB/FB - Hardware: (8) 30mm Bed Bolts, (8) Silver Cap Nuts, (1) Hex Key
& (4) Wood Plugs
Carton #3: (4) Full Top Rails - Hardware: (3) Full Bed Wires and (6) 1” Bed Wire Screws
Carton #4: (2) Full Bottom Rails - Hardware: (3) Full Bed Wires and (6) 1” Bed Wire Screws
Carton #5: (1) Ladder - Hardware: (4) Wood Screws
#4016 and #MC16 TWIN/FULL BUNK BED (4 CARTONS TOTAL)
Carton #1: (2) Top HB/FB - Hardware: (4) Metal Pins, (8) 30mm Bed Bolts, (8) Silver Cap Nuts, (8) 70mm
Lag Bolt Screws
Carton #2: (2) Bottom HB/FB - Hardware: (8) 30mm Bed Bolts, (8) Silver Cap Nuts, (1) – Hex Key
& (4) Wood Plugs
Carton #3: (4) Twin Top Rails - Hardware: (3) Twin Bed Wires and (6) 1” Bed Wire Screws
Carton #4: (2) Full Bottom Rails - Hardware: (3) Full Bed Wires and (6) 1” Bed Wire Screws
#4016F and #MC16F FULL/FULL BUNK BED (4 CARTONS TOTAL)
Carton #1: (2) Top HB/FB - Hardware: (4) Metal Pins, (8) 30mm Bed Bolts, (8) Silver Cap Nuts, (8) 70mm
Lag Bolt Screws
Carton #2: (2) Bottom HB/FB - Hardware: (8) 30mm Bed Bolts, (8) Silver Cap Nuts, (1) Hex Key
& (4) Wood Plugs
Carton #3: (4) Full Top Rails - Hardware: (3) Full Bed Wires and (6) 1” Bed Wire Screws
Carton #4: (2) Full Bottom Rails - Hardware: (3) Full Bed Wires and (6) 1” Bed Wire Screws
#4019 and #MC19 TWIN/FULL PANEL BUNK BED (5 CARTONS TOTAL)
Carton #1: (2) Top HB/FB - Hardware: (4) Metal Pins, (8) 30mm Bed Bolts, (8) Silver Cap Nuts, (8) – 70mm
Lag Bolt Screws
Carton #2: (2) Bottom HB/FB - Hardware: (8) 30mm Bed Bolts, (8) Silver Cap Nuts, (1) Hex Key
& (4) Wood Plugs
Carton #3: (4) Twin Top Rails - Hardware: (3) Twin Bed Wires and (6) 1” Bed Wire Screws
Carton #4: (2) Full Bottom Rails - Hardware: (3) Full Bed Wires and (6) 1” Bed Wire Screws
Carton #5: (1) Ladder - Hardware: (4) Wood Screws
TOOLS REQUIRED
Phillips Screwdriver or Electric Drill
Hex Key (Provided)
#4013F,#4016, #4016F, #4019,#MC13F, #MC16, #MC16F, #MC19 ASSEMBLY INSTRUCTIONS
1. Check cartons to be sure all wooden parts and hardware is included.
2. To begin assembly, obtain carton #1 (top HB/FB) and carton #3 (4 top rails).
3. Hold the top HB upright. Insert 30mm bed bolts through bottom set of holes on top HB and metal bracket on
cleated rail as shown in Fig.2. Secure with silver cap nuts but do not fully tighten.
4. Repeat step 3 for other side of HB.
5. Attach the FB to opposite side using same method as in steps 3 and 4.
6. Attach one guard rail to top set of holes of HB by securing 70mm Lag Bolt Screws thru HB holes and into
pre-drilled holes in end of guard rail as shown in Fig.3. Secure but do not fully tighten. Attach the other end
of guardrail to the FB in same manner.
7. Repeat step 6 for other rail on opposite side.
8. Now, go back and fully tighten all cap nuts and bolts to secure bed.
9. Secure bed wires with bed wire screws to both sets of cleated rails as shown in Fig.4.
10. To assemble the bottom bed, obtain carton #2 (bottom HB/FB) and carton #4 (full bottom Rails) and repeat
steps 3, 4, 5, 8 & 9 as shown in Fig. #1.
11. Obtain the metal bed pins and insert into the pre-drilled holes on the top of each side post of the bottom bunk
as shown in Fig.5.
12. You may now stack the bed. Do not leave the upper bunk unattached, even if it isn't used for a sleeping area
it may be dislodged and fall resulting in serious injury or death.
13. For model #4013F, #4019 or #MC13F, obtain carton #5 (ladder) and secure with wood screws as shown in
Fig.6
14. Insert wood plugs into four open holes on top of bottom headboard and footboard. Push firmly until plugs are
completely in holes.