Pine Crafter Furniture 18 User manual

18-18F
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE THIS BED
MATTRESS SIZES…
Bed Mattresses Specifications:
Use only a mattress meeting the following specifications on the upper and lower bunks.
Bed Type Width Length Bed Type Width Length
Standard Twin 37½”-38½” 74”-75” XL Twin 37½”-38½” 79”-80”
Standard Full 52½”-53½” 74”-75” XL Full 52½”-53½” 79”-80”
Total thickness of both mattress and foundation MUST NOT EXCEED 6½” for top and bottom bunks.
SAFETY WARNINGS AND GENERAL NOTES
Follow information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
or entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guard rails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guard rails on both sides of the upper bunk.
The use of water or sleep floatation mattresses is prohibited.
Prohibit more than one person on the upper bunk.
Keep these instructions for future references.
We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet. Be
certain all staples are out of the box before beginning assembly on the shipping carton.
Strangulation Hazard - Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts and jump ropes.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be obtained from any of our Pine Crafter
dealers.

18 & 18F INSTRUCTIONS
CARTON CONTAINERS
#18 TWIN/TWIN POST BUNK BED (5 CARTONS TOTAL)
1 Box (2) Twin Top HB/FB (Hardware: 4 – Metal Pins, 16 – 80mm Bed Bolts, 16 - Weld Nuts)
1 Box (2) Twin Bottom HB/FB (Hardware: 8 – 80mm Bed Bolts, 8 – Weld Nuts)
1 Box Ladder (Hardware: 4 – 2” Wood Screws)
1 Box (2) Cleated Rails (2) Guardrails (Hardware: 3 – Twin Bed Wires and 6 – 1” Bed Wire
Screws)
1 Box (2) Cleated Rails (Hardware: 3 – Twin Bed Wires and 6 – 1” Bed Wire Screws)
#18F FULL/FULL POST BUNK BED (5 CARTONS TOTAL)
1 Box (2) Full Top HB/FB (Hardware: 4 – Metal Pins, 16 – 80mm Bed Bolts, 16 - Weld Nuts)
1 Box (2) Full Bottom HB/FB (Hardware: 8 – 80mm Bed Bolts, 8 – Weld Nuts)
1 Box Ladder (Hardware: 4 – 2” Wood Screws)
1 Box (2) Cleated Rails (2) Guardrails (Hardware: 3 – Full Bed Wires and 6 – 1” Bed Wire
Screws)
1 Box (2) Cleated Rails (Hardware: 3 – Full Bed Wires and 6 – 1” Bed Wire Screws)
TOOLS REQUIRED
Phillips Screwdriver or Electric Drill
Hex Key (Provided)
ASSEMBLY INSTRUCTIONS
1. Check cartons to be sure all wooden parts and hardware is included.
2. To begin assembly, obtain one top HB/FB and 2 cleated rails.
3. Hold the HB/FB upright. Insert 80mm bed bolts through pre-drilled holes on top HB/FB
and continue through metal bracket on rail and secure with weld nuts as shown in
Figure 1.
4. Repeat step 3 for the other side.
5. Attach another top HB/FB to the other end using the same method as in steps 3 & 4.
6. Obtain one guard rail and assemble to the top holes in the upper bunk headboard in
the same manner as in step 3. Repeat this for the other side.
7. Repeat step 6 for the other rail.
8. Secure bed wires with bed wire screws to cleated rails as shown in Figure 4.
9. To assemble the bottom bed repeat steps 2, 3, 4, 5, & 8.
10. Find the metal bed pins and insert into the pre-drilled holes in the top of each leg of
the lower bunk as shown in Figure 1.
11. You may now stack the bed. Do not leave the upper bunk unattached, even if it isn't
used for a sleeping are. It may be dislodged and fall resulting in serious injury or death.
12. Attach ladder to bed as shown in Figure #4.
Note: Gap between ladder and top headboard edge must be less than 3”.