Pine Crafter Furniture 3972 User manual

72 - 76
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE THIS BED
MATTRESS SIZES…
Bed Mattresses Specifications:
Upper twin bed is designed to use mattresses and foundations 37½”-38½” wide and 74”-75” long.
Total thickness of both mattress and foundation MUST NOT EXCEED 6½” for upper bunk.
SAFETY WARNINGS AND GENERAL NOTES
Follow information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
or entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guard rails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guard rails on both sides of the upper bunk.
The use of water or sleep floatation mattresses is prohibited.
Prohibit more than one person on the upper bunk.
Keep these instructions for future references.
We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet. Be
certain all staples are out of the box before beginning assembly on the shipping carton.
Strangulation Hazard - Never attach or hang items to any part of the bunk bed that are not designed
for use with the bed; for example, but not limited to, hooks, belts and jump ropes.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be obtained from any of our Pine Crafter
dealers.

72 and 76 INSTRUCTIONS
#72 CARTON CONTAINERS
1 Box (2) Upper HB/FB (2) Lower HB/FB (4) Casters with inserts (Hardware: 24 – 30mm bed
bolts, 24 – cap nuts, 8 – L-Brackets, 16 – ¾” screws and 1 hex key)
1 Box Loft Desk
1 Box Loft Chest
1 Box Loft Ladder (Hardware: 4 – 3-½” wood screws)
1 Box (2) Cleated Rails (2) Guard Rails (Hardware: 3 – bed wires and 6 – bed wires screws)
1 Box (2) Cleated Rails (Hardware: 3 – bed wires and 6 – bed wires screws)
#76 CARTON CONTAINERS
1 Box (2) Upper HB/FB (Hardware: 16 – 30mm bed bolts, 16 – cap nuts)
1 Box Loft Desk
1 Box Loft Chest
1 Box Loft Ladder (Hardware: 4 – 3-½” wood screws)
1 Box (2) Cleated Rails (2) Guard Rails (Hardware: 3 – bed wires and 6 – bed wires screws)
ASSEMBLY TOOLS REQUIRED
Phillips Screwdriver or Electric Drill
Hammer or Mallet
Hex Key (Provided)
ASSEMBLY INSTRUCTIONS
1. Check cartons to be sure all wooden parts and hardware is included.
2. To begin assembly, obtain upper bunk HB/FB and two cleated rails.
3. Hold the HB/FB upright, insert 30mm bed bolts through metal bracket and bottom holes
on HB/FB and secure with cap nuts, as shown in Figure 1.
4. Repeat step 3 for the other side.
5. Attach another upper bunk HB/FB to the other end using same method as in steps 3
and 4.
6. Obtain one guard rail and assemble to the top holes in the upper bunk headboard in
the same manner as in step 3. Repeat this for the other side.
7. Repeat step 6 for other rail.
8. Now position the unit’s desk and/or chest in the area you have selected for set-up.
Once the units are properly positioned, you can lift the upper bunk assembly into place.
The upper bunk will rest directly on top of the desk and chest. The bed should be
positioned approximately ½” back from the ends and edges, as shown in Figure 2.
The loft bed must be secured into position using the “L” brackets and the ¾” screws,
as shown in Figure 2. Do not leave the upper bunk unattached. Even if it isn’t used for
a sleeping area it may be dislodged and fall resulting in serious injury or death.
9. To assemble the lower bunk repeat steps 2, 3, 4, and 5.
10. Turn bed upside down and insert the knock-in inserts in the pre-drilled holes in the
bottom of the HB/FB (a light tap with a hammer or mallet will secure the inserts. Push
casters into inserts.
11. Turn bed upright and roll bed underneath top loft.
12. Attach ladder with 3-½” wood screws, as shown in Figure 3.
13. Secure bed wires with bed wire screws to top of cleat on cleated rails, as shown in
Figure 4.