Pine Crafter Furniture 78 User manual

78 - 78F - 99 - 99F
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE THIS BED
MATTRESS SIZES…
Bed Mattresses Specifications:
Upper twin bed is designed to use mattresses and foundations 37½”-38½” wide and 74”-75” long.
Upper full bed is designed to use mattresses and foundations 52½”-53½” wide and 74”-75” long.
Total thickness of both mattress and foundation MUST NOT EXCEED 6½” for upper bunk.
SAFETY WARNINGS AND GENERAL NOTES
Follow information on the warnings appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
or entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guard rails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guard rails on both sides of the upper bunk.
The use of water or sleep floatation mattresses is prohibited.
Prohibit more than one person on the upper bunk.
Keep these instructions for future references.
We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet. Be
certain all staples are out of the box before beginning assembly on the shipping carton.
Strangulation Hazard - Never attach or hang items to any part of the bunk bed that are not designed
for use with the bed; for example, but not limited to, hooks, belts and jump ropes.
REPLACEMENT PARTS
Replacement parts, including additional guardrails, may be obtained from any of our Pine Crafter
dealers.

78, 78F, 99, and 99F INSTRUCTIONS
78, 78F BOX CONTAINERS
1 Box (2) HB/FB (Hardware: 20 – 30mm bed bolts, 20 – cap nuts, 1 – hex key, & 4 – 1-¼”
wood screws)
1 Box (1) Jr. Ladder (Hardware: 4 – 3-½” wood screws)
1 Box (1) Jr. Loft Roll-Out Desk
1 Box (1) Jr. Loft Bookcase
1 Box (1) Three Drawer Chest
1 Box (4) Twin Top Rails (Hardware: 3 – bed wires and 6 – 1” bed wire screws)
1 Box (1) Support Rail (Hardware: 4 – L-Brackets and 8 – ¾” wood screws)
99, 99F BOX CONTAINERS
1 Box (2) HB/FB (Hardware: 20 – 30mm bed bolts, 20 – cap nuts, 1 – hex key, & 4 – 1-¼”
wood screws)
1 Box (1) Jr. Ladder (Hardware: 4 – 3-½” wood screws)
1 Box (1) Six Drawer Mini Dresser
1 Box (1) Three Drawer Chest
1 Box (4) Twin Top Rails (Hardware: 3 – bed wires and 6 – 1” bed wire screws)
1 Box (1) Support Rail (Hardware: 4 – L-Brackets and 8 – ¾” wood screws)
ASSEMBLY TOOLS REQUIRED
Phillips Screwdriver or Electric Drill
Hex Key (Provided)
ASSEMBLY INSTRUCTIONS
1. Check cartons to be sure all wooden parts and hardware is included.
2. To begin assembly, obtain one HB/FB and two top guard rails.
3. Hold the HB/FB upright, insert 30mm bed bolts through metal bracket of top guard rail
and top holes on HB/FB and secure with cap nuts.
4. Repeat step 3 for the other side.
5. Attach another HB/FB to the other end using same method as in steps 3 & 4.
6. Obtain one cleated rail and assemble to the center holes in the upper bunk headboard
in the same manner as in step 3. Repeat this for the other side.
7. Repeat step 6 for other rail.
8. Secure bed wires with bed wire screws to top of cleated rails, as shown in Figure 2.
9. To assemble the bottom support rail use L-Brackets and ¾” wood screws as shown in
Figure 1.
10. Now slide desk, bookcase, chest and/or dresser underneath bed, as shown in photos
for your model.
11. Attach ladder to end of bed, as shown in Figure 3.