Planet DVR-462 User manual

DVR-462 DVR-462
Quick GuideQuick Guide
2011-AB5390-001
PLANET Technology Corporation
Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw
11F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
STEP 1: Remove the 3 screws from DVR-462 STEP 2: Follow the direction to remove the
upper case
SATA cable
DVR-462 I/O Cable
CD Disk
Power Adapter
Battery x 2 Remote Controller
HDD Screw x 4
For detailed information about DVR-462, please refer to the User’s Manual in the CD disk.
STEP 3: Place the HDD on the HDD plate of the
removed case and connect the power
and the SATA cable STEP 4: Put back the upper case and tight the
three screws
Note: Before HDD installation, please make sure there is no pre-configured partition in this HDD.
If yes, please delete all the partition before install.
► Hard Disk Installation
► Contents ► Hardware Connection
Please follow the sequence from 1 to 9 to connect the equipments to DVR-462.
1 DC 12V
2 MAIN / SPOT MONITOR
3 VIDEO IN
4 VGA
5 AUDIO IN
6 AUDIO OUT
7 EXTERNAL I/O
8 LAN
9 USB
Socket for a DC 12V power input.
BNC port for the main monitor connected and display full screen image of all installed cameras in sequence.
BNC input ports for cameras, 4 in total.
Connect your PC monitor to this connector. If the MAIN port is connected, VGA port will lost function.
You have to choose the VGA or MAIN for monitoring.
RCA input port for an audio signal.
RCA output port for an audio signal.
EXTERNAL I/O port.
Network port. Connect to your switch or PC directly.
Connect your USB mouse to control this DVR.
DescriptionItem
Camera 1~4
Mouse
Audio InputVGA Output
Main/Spot Monitor Output Audio Output
RS485/Relay/Sensor
Power Supply
Network Connection
Quick Installation Guide

DVR-462 DVR-462
Quick GuideQuick Guide
2011-AB5390-001
PLANET Technology Corporation
Tel: [phone] Fax: [phone]
Email: [e-mail] www.planet.com.tw
11F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
STEP 1: Remove the 3 screws from DVR-462 STEP 2: Follow the direction to remove the
upper case
SATA cable
DVR-462 I/O Cable
CD Disk
Power Adapter
Battery x 2 Remote Controller
HDD Screw x 4
For detailed information about DVR-462, please refer to the User’s Manual in the CD disk.
STEP 3: Place the HDD on the HDD plate of the
removed case and connect the power
and the SATA cable STEP 4: Put back the upper case and tight the
three screws
Note: Before HDD installation, please make sure there is no pre-configured partition in this HDD.
If yes, please delete all the partition before install.
► Hard Disk Installation
► Contents ► Hardware Connection
Please follow the sequence from 1 to 9 to connect the equipments to DVR-462.
1 DC 12V
2 MAIN / SPOT MONITOR
3 VIDEO IN
4 VGA
5 AUDIO IN
6 AUDIO OUT
7 EXTERNAL I/O
8 LAN
9 USB
Socket for a DC 12V power input.
BNC port for the main monitor connected and display full screen image of all installed cameras in sequence.
BNC input ports for cameras, 4 in total.
Connect your PC monitor to this connector. If the MAIN port is connected, VGA port will lost function.
You have to choose the VGA or MAIN for monitoring.
RCA input port for an audio signal.
RCA output port for an audio signal.
EXTERNAL I/O port.
Network port. Connect to your switch or PC directly.
Connect your USB mouse to control this DVR.
DescriptionItem
Camera 1~4
Mouse
Audio InputVGA Output
Main/Spot Monitor Output Audio Output
RS485/Relay/Sensor
Power Supply
Network Connection
Quick Installation Guide