Planet NVT-401 User manual

4/8/16/32-Ch Network Video Recorder
NVR-401 / NVR-810 / NVR-1610 / NVR-3210
Quick Installation Guide

Table of Contents
Chapter 1. Introduction .................................................................................... 3
1.1 Before Installation ............................................................................... 3
Chapter 2. Physical Description and Installation.................................................. 4
2.1 4-Ch Network Video Recorder............................................................... 4
2.1.1 NVR-401 Package Content........................................................... 4
2.1.2 NVR-401 Physical Details ............................................................ 4
2.1.3 NVR-401 Installation................................................................... 5
2.2 8/16-Ch Network Video Recorder .......................................................... 7
2.2.1 NVR-810 / NVR-1610 Package Content......................................... 7
2.2.2 NVR-810 / NVR-1610 Physical Details .......................................... 7
2.2.3 NVR-810 / NVR-1610 Installation................................................. 8
2.3 32-Ch Network Video Recorder ............................................................10
2.3.1 NVR-3210 Package Content........................................................10
2.3.2 NVR-3210 Physical Details..........................................................10
2.3.3 NVR-3210 Installation ................................................................11
2.4 Web Management...............................................................................13

3
Chapter 1. Introduction
Thank you for purchasing the PLANET 4/8/16/32-Ch Network Video Recorder. The
Network Video Recorder is designed for use within a surveillance system, and
performs recordings and playbacks pictures from network cameras in the system.
It is a recording device using a hard disk drive to record camera pictures instead
of using video tapes so that pictures recorded by repeated overwriting will not
experience deterioration of the recorded picture quality. Up to 4 (for NVR-401) and
8 (for NVR-810) and 16 (for NVR-1610) and 32 (for NVR-3210) cameras can be
connected via a network and it is possible to record their camera pictures. It is
possible to perform the settings or operate the NVR using a web browser installed
on a PC connected to a network, or remote controller. Recorded video can be
played back from remote site by a PC. Up to 4 PCs (web browsers) can access
this unit concurrently and it is possible to perform the settings and operate this
unit. The NVR is compatible with most major brand cameras and its ability to
automatically search and nd the available cameras on the network can greatly
reduce the user effort when expanding the system.
1.1 Before Installation
Before installation, please be sure to read this quick installation guide and user’s
manual (CD) carefully to complete machine installation. This guide shows how
to quick set up the NVR, unless model name specied terms “Network Video
Recorder” will be used for these models.

4
Chapter 2. Physical Description and Installation
2.1 4-Ch Network Video Recorder
2.1.1 NVR-401 Package Content
1 x NVR 1 x Power Cord 1 x Power Adapter
1 x RJ-45 Cable 1 x CD-ROM 8 x HDD Screw
1 x Quick Installation Guide
2.1.2 NVR-401 Physical Details
Front Panel
LEDs Color Description
Power Blue On: Power on.
Off: Power off.
HDD Green Blinking: HDD is accessing.
Off: HDD is no action.
Button Description
Power Press to start or shut down.
Connector Description
USB Connect your USB ash disk for rmware upgrade.

5
Rear Panel
Connector Description
DC Connector Connect the bundled power adapter.
Ethernet Supports 10/100/1000Base-T interface.
USB Connect your USB ash disk for rmware upgrade.
Button Description
Reset Press to reset NVR to factory default.
2.1.3 NVR-401 Installation
2.1.3.1 Installing the Hard Disk Drive
1. Push the silver button to release the HDD tray.

6
2. Pull out the HDD tray.
3. Place the HDD on the tray and secure the HDD with the screws at the bottom
(as illustrate).
4. Push the tray back in the unit and press down the black bar to secure the tray.

7
2.2 8/16-Ch Network Video Recorder
2.2.1 NVR-810 / NVR-1610 Package Content
1 x NVR 1 x Power Cord 1 x RJ-45 Cable
1 x CD-ROM 2 x HDD Screw 1 x Quick Installation Guide
2.2.2 NVR-810 / NVR-1610 Physical Details
Front Panel Description
NVR-1610
IP Camera
Status LED
Reset
Button
Power
Button
Buzzer
Button USB Port
NVR Status LEDs
NVR-1610
Network Video Recorder
PowerReset Buzzer
123456789
10 11 12 13 14 15 16
Power Status Network HDD1 HDD2 Alarm
NVR-810
IP Camera
Status LED
Reset
Button
Power
Button
Buzzer
Button USB Port
NVR Status LEDs
NVR-810
Network Video Recorder
PowerReset Buzzer
1 2 3 4 5 6 7 8
Power Status Network HDD1 HDD2 Alarm

8
2.2.3 NVR-810 / NVR-1610 Installation
2.2.3.1 Installing the Hard Disk Drive
1. Removing the screws on the side.
2. Push the top housing forward, then lift it up.
3. Removing the screws on the HDD Tray left and right side.
HDD
Tray

9
4. Insert the HDD to HDD tray. Please push the HDD until the SATA connect is
connected properly, and lock the HDD Screw on left and right side.
HDD
5. If there is a second HDD, please repeat the step 4 to install it.
6. Place the top housing back and secure it with the bottom housing.
7. Connect the bundle power adapter to the power connector in rear panel.
8. Press power button to power on your NVR.

10
2.3 32-Ch Network Video Recorder
2.3.1 NVR-3210 Package Content
1 x NVR 1 x Power Cord 1 x RJ-45 Cable
1 x CD-ROM 12 x HDD Screw 1 x Quick Installation Guide
2.3.2 NVR-3210 Physical Details
Front Panel
Reset/Restart button
Power LED
Power Button
Event LED
USB
System LED
LEDs Color Description
System Amber
Firmware upgrade: blinking
System failure (AP fail): off
System normal: solid
Event Amber Event recording: solid
No event: off
Power Blue Power on/Restart/Reset to default/OS fail: stays solid

11
2.3.3 NVR-3210 Installation
2.3.3.1 Installing the Hard Disk Drive
1. Release the HDD tray by pulling the lock to the right.
2. Pull the HDD tray out of the case.

12
3. Place the HDD in the tray and the bottom of the tray.
4. Put the HDD tray back to the case.
5. Push the tray door back to the case to secure it.

13
2.4 Web Management
Install “Device Search” utility from the CD
1. Please go to Start => Programs => NVR => Search NVR to run the search tool.
Then you will see the utility start search the network.
2. The NVR should be located and its IP address should be displayed: Double-click
on it and the program should automatically access the NVR’s web administration
page from your default browser.
3. Login the Homepage
The Web management allows you to access and manage the Network Video
Recorder easily. Launch the Web browser and then enter the IP address. The
default IP address is 192.168.0.20. And, ll the User Name and Password to
login the Web management. The default User Name / Password is admin /
admin.

14
Further congurations and information can be found in the user’s manual CD.
Please check the user’s manual for more understanding.

This page is intentionally left blank

This page is intentionally left blank