PMK FireFly FF-HAL10kV User manual

Instruction Manual
FireFly®Probe Positioners
Hands-free Testing
0 °C to +50 °C
DE | EN

FireFly® Probe Positioners Instruction Manual
2
FireFly®Probe Positioners
The FireFly® probe positioners offer precise and semi-permanent positioning for FireFly® optically-
isolated probes, minimizing the risk of unwanted movement that could damage the device under test or
result in an unsafe condition. These positioners act as a reliable "third helping hand". One of the key
advantages of the FireFly® probe positioners is their quick and easy setup process, saving valuable
time and effort by moving the probe into the desired position and holding it securely in place.
Specifications
FireFly®products are not rated for CAT II, III or IV. Do not exceed the specifications. Review also the
the FireFly®Series Instruction Manual. The following ratings are according to IEC 61010-031:2023-05.
Electrical Specifications of FF-HAL10kV and FF-3DPOS200
Rating for Measurement Category not II, III or IV:
Maximum Rated Insulating Voltage
10 kV (DC + Peak AC)
Pollution Degree
2
Electrical Specifications of FF-2FOOTER
Rating for Measurement Category not II, III or IV:
Maximum Rated Insulating Voltage
30V AC / 60V DC
Pollution Degree
3
Environmental Specifications
Altitude
Operating
up to 2000 m
Non-operating
up to 15000 m
Temperature Range
Operating
0 °C to +50 °C
Non-Operating
-40 °C to +71 °C
Maximum Relative
Humidity
Operating
80 % relative humidity for temperatures up to
+31 °C, decreasing linearly to 40 % at +50 °C
Non-operating
95 % relative humidity for temperatures up
to +40 °C
Maintenance and General Notes
The 3D Probe Positioners are almost maintenance-free. However, if the device is exposed to pollution,
regular cleaning is necessary. Remove dust and dirt from the joints.
Make sure to use any FireFly®probe positioner in a clean lab environment without any
pollution, dust or dirt to maintain the specified isolation voltage.
For cleaning purposes use standard cleaning agents commercially available. Don`t use any lye or acids.
Apply a little amount of lubricant to the screws and joints, as needed.
Scope of Delivery
•FireFly®Positioning System (FF-3DPOS200) including Wrench 7mm, FireFly®Probe Head
Holder Set FF-HAL10kV-3 or FireFly®2-Footer (FF-2FOOTER)
•Instruction Manual

FireFly® Probe Positioners Instruction Manual
3
Getting Started
Read also the FireFly®Instruction Manual before first use, and keep both for future reference. A digital
copy of the latest Instruction Manual revisions can be downloaded at www.pmk.de. The use of this
equipment is for qualified personnel only. Observe adequate spacing between FireFly®probe head
components and earth ground. Note, FireFly®products are not rated for CAT II, III or IV. To achieve the
most accurate measurement results, review the “Getting Started” section in the FireFly®Series
Instruction Manual.
Clamping the FireFly®Probe (all models)
Insert the FireFly®probe from the top into the holder. Before turning the FireFly®probe by 90° to mount
or unmount, make sure the probe is fully inserted and seated into the holder. The following example is
also valid when using the bi-pod FF-2FOOTER.
The FireFly®probe holders consist of insulating material.
Only the holder FF-HAL10kV, which is equipped with the 3D probes positioner
FF-3DPOS200, provides isolation voltages up to 10kV.
Observe the required distances of FireFly®probe head to earth ground.
Insert / remove probe
Make sure probe head is fully
inserted and seated into holder
Twist by 90°
to mount or unmount
Using the Holders FF-3DPOS200 and FF-HAL10kV
•Assembly
Screw the positioner arm [B] into the product specific base [A] with M6 thread, and tighten it with the
7mm wrench from the scope of delivery. The base [A] is available in three different
variants: Steel base, vacuum base or table clamp. The positioner arms [B] with M6 thread
are available with 130mm and 200mm span width.
The probe holder [C] shape depends on the probe being in use. For the FireFly®Series use the FF-
HAL10kV only. The drawing below shows as example of the universal probe holder.
Assembly Overview, Example Tensioning knob [D], Example
[C2
]
[C1
]
[A]
[B]
[C]
[D]

FireFly® Probe Positioners Instruction Manual
4
•Handling and Re-Positioning
Hold the 3D Probe Positioner and loosen the central tensioning knob [D] until the 3D Probe Positioner
can be moved.
Do not release the tensioning knob [D] completely, otherwise the 3D Probe Positioner
collapses in itself and could damage your measuring setup.
If you are using MMCX as the input connector, disconnect the MMCX connector from the circuit under
test before repositioning the probe and its holder, otherwise you may cause unnecessary mechanical
stresses on the MMCX connector and the PCB.
Bring the 3D Probe Positioner into the desired position and fix the device by turning the central
tensioning knob [D] contrary.
Ordering Information
All components are compatible with parts from the PMK positioning systems series. If a 3D positioning
system from PMK is available already, only the FireFly®probe holder FF-HAL-10kV is needed. For
spare parts and more positioners, visit us at www.pmk.de
Order No.
Item
Picture
FF-3DPOS200
FireFly® 3D Probe Positioner for 10kV Insulation with steel base
(893-100-001), arm with span width 200mm (893-200-200),
FireFly® probe holder (FF-HAL10kV), Wrench 7mm
FF-HAL10kV
FireFly® Series non-conducting High Voltage Differential Probe
Holder for 10kV Voltage Insulation, M6 thread, pack of three
893-000-SW7
Wrench 7mm – spare part
FF-2FOOTER
FireFly® Probe Holder 2-Footer (Bipod) – spare part
Copyright © 2023 PMK - All rights reserved.
Information in this publication supersedes that in all previously published material.
Specifications are subject to change without notice.
Manufacturer
PMK Mess- und Kommunikationstechnik GmbH
Königsteiner Str. 98
65812 Bad Soden, Germany
Tel: [phone]
Internet: www.pmk.de
E-Mail: [email protected]
Warranty
PMK warrants this product for normal use and operation within specifications for a period of one year
from date of shipment and will repair or replace any defective product, which was not damaged by
negligence, misuse, improper installation, accident or unauthorized repair or modification by the buyer.
This warranty is applicable only to defects due to material or workmanship. PMK disclaims any other
implied warranties of merchantability or fitness for a particular purpose. PMK will not be liable for any
indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of
business, loss of use or data, interruption of business and the like), even if PMK has been advised of
the possibility of such damages arising from any defect or error in this manual or product.
M-FF-POSITIONERS Revision 01-2023
a