PNI ESCORT HP 6500 User manual

1、Introduction
Thank you for your choose and buy the Nanfone CB Radio. In order
to make your CB Radio to use in the best condition, please read this
manual in detail.PNI Escort HP 6500 is a small, simple
operation and convenient vehicle CB Radio which has good
performance.
Feature：
Up/down keys on the microphone
Scan channel
LCD display
Auto ASQ/SQ adjustable
RF GAIN
External Speaker
2、Installation instructions
Check the materials before the installation, car charger is
connected to the car's 12 v power supply socket，the radio’s positive
and negative electrode connected to the car charger’s. Power
supply support 12 V to 13.8 V. Check all wiring are in good condition
before starting, ensure do not short circuit, ensure the radio can
boot running normally.
User Manual

3、Control panel function
Front view
No
Name
Short Press
Function
Long Press
Function
①
Microphone
socket
②
A/F
AM/FM Mode
Switch
Scan Function
③
LCD Display
④
Power On/Off
Volume

4、Operation
4.1 Power On/Off the radio
1. Turn VOL switch clockwise to power on the radio, the LCD
full screen display after spectrum model 1 s into the channel
state.
2. Turn the VOL Knob counterclockwise, until it clicks. The
radio is power off.
4.2 Volume Control
Turn clockwise to increase volume, turn counterclockwise to
decreases volume.
4.3 Channel Selection
1. Shortly press microphone【UP】or【DOWN】to change
working channel.
⑤
、
⑥
Channel
UP/DOWN
select
⑦
EMG(Emergen
cy Channel ）
9/19 Channel
Switch
⑧
RFG
Enter RF GAIN
Model
⑨
SQ/ASQ
Function Switch
Enter SQ (ASQ)
Level Switch
Switch To ASQ
Mode

2.Hold microphone 【UP】or【DOWN】to change working
channel fast.
4.4 Squelch level control
1.Shortly press【SQ】,until LCD shortly displays SQ and then
display X.X。X.X stands for the SQ level
0.F
SQ off
0.1
Lowest SQ level
…
…
2.8
Highest SQ level
2.Press microphone【UP】/【DOWN】shortly to change SQ
level.
3.Hold microphone【UP】/【DOWN】to change the SQ level
fast.
4.Hold【SQ】or wait for 3 seconds to store and exit.
4.5 ASQ control（9 level）
1. Hold【SQ】key，until LCD display AQ，the ASQ function
is turned on. The LCD will display A.X。X stands for the
ASQ level。
A.1
Lowest ASQ level
…
…
A.9
Highest ASQ level

2. Shortly press microphone【UP】/【DOWN】to change
ASQ level.
3. Hold microphone【UP】/【DOWN】to change ASQ level
fast.
4. Hold【SQ】or wait for 3 seconds to store and exit.
4.6 Modulation Type
Shortly press【A/F】key to switch between AM/FM mode
and the LCD displays the selected mode.
4.7 RF GAIN control
1.Shortly press【RFG】key，LCD displays R and the present
RF GAIN level flashes.
2.Shortly press microphone【UP】/【DOWN】to change the
level.
3.Shortly press【RFG】key to exit RF GAIN level control.
4.8 Emergency Channel
1.Shortly press【EMG】key to choose CH9，the channel
number flashes.
2.Shortly press 【EMG】key again to choose CH19，the
channel number flashes.
3. Shortly press【EMG】key third time to return to last normal
channel.

4.9 Key Lock
1.Hold【EMG】key for over 2 seconds to lock the keys, LCD
displays “LC”.
2.Hold【EMG】for over 2 seconds again to unlock the keys,
LCD displays “OF”.
4.10 Scan Function
1.Hold【A/F】to start scan function，LCD displays“SC”.
2.Press microphone【UP】/【DOWN】can choose scanning
clockwise or counterclockwise.
3.Press【A/F】or【PTT】key to exit scan function.
4.11 Changing the CB-Standard
1. Hold【A/F】while powering the radio on, until LCD
displays the norms.
2.Press microphone【UP】/【DOWN】to choose wanted
Norms.
3.Power off and power on again
Standard
Channels
Fequency Range
EU
40FM/40AM
26.965-27.405MHZ
CE
40 FM
26.965-27.405MHZ
UK
40 FM
27.60125-27.99125MHZ

PL
40FM/40AM
26.960-27.400MHZ
I2
34FM/34AM
26.965-26.865MHZ
DE
40FM/40AM
26.965-27.405MHZ
80FM
26.565-26.955MHZ
IN
27FM/27AM
26.965-27.275MHZ
4.12 Restore factory default
1.Hold【SQ】key while powering the radio on, until the LCD
displays “rt”.
2. All channel and function setting will resume factory default
after above operation.
FCC Statement:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.This equipment complies with FCC radiation exposure limis set forth for an uncontrolled environment.This equipment should be instslles and operated with minimum distance 50cm between the radiator&your bady.