Pottinger EUROCAT 271 classic User manual

Operator‘s manual
GB
+ INSTRUCTIONS FOR PRODUCT DELIVERY . . . Page 3
"Translation of the original Operating Manual" Nr.
s $RUM MOWER
 '"-
EUROCAT 271 classic
(Model PSM 3542 : + . . 01001)
EUROCAT 311 classic
(Model PSM 3552 : + . . 01001)

ALLG./BA SEITE 2 / 0000-GB
Important information concerning Product
Liability.
According to the laws governing product liability, the manufacturer and dealer are obliged to hand the
operating manual to the customer at the time of sale, and to instruct them in the recommended operating,
safety, and maintenance regulations. Confirmation is necessary to prove that the machine and operating
manual have been handed over accordingly.
For this purpose,
- document A is to be signed and sent to Pöttinger,
- document B remains with the dealer supplying the machine,
- and the customer receives document C.
In accordance with the laws of product liability, every farmer is an entrepreneur.
According to the laws of product liability, property damage is damage caused by a machine and not to
it. An excess of Euro 500 is provided for such a liabilioty.
In accordance with the laws of product liability, entrepreneurial property damages are excluded from
the liability.
Attention! Should the customer resell the machine at a later date, the operating manual must be given
to the new owner who must then be instructed in the recommended regulations referred to herein.
GB Dear Farmer
You have just made an excellent choice. Naturally we are very happy
and wish to congratulate you for having chosen Pöttinger. As your
agricultural partner, we offer you quality and efficiency combined with
reliable servicing.
In order to assess the spare-parts demand for our agricultural machines
and to take these demands into consideration when developing new
machines, we would ask you to provide us with some details.
Furthermore, we will also be able to inform you of new developments.
Pöttinger Newsletter
www.poettinger.at/landtechnik/index_news.htm
The latest expert information, useful links and entertainment

Dokument D
GB-0600 Dokum D Anbaugeräte
PÖTTINGER Landtechnik GmbH
Industriegelände 1
A-4710 Grieskirchen
Tel. 07248 / 600 -0
Telefax 07248 / 600-2511
TMachine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating
devices at hand.
TOperation and maintenance of machine and/or implement according to operating instructions explained to the customer.
TTyres checked re. correct pressure.
TWheel nuts checked re. tightness.
TDrive shaft cut to correct lenght.
T*VYYLJ[WV^LY[HRLVɈZWLLKPUKPJH[LK
TFitting to tractor carried out: to three-point linkage
TTrial run carried out and no defects found.
TFunctions explained during trial run.
TPivoting in transporting and operating position explained.
TInformation given re. optional extras.
TAbsolute need to read the operating manual indicated.
Please check. X
According to the product liability please check the above mentioned items.
INSTRUCTIONS FOR
PRODUCT DELIVERY
GB
In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.
For this purpose please do the following:
- sign the document A and send it to the company Pöttinger or via the internet to www.poettinger.at
- document B stays with the specialist factory delivering the machine.
- document C stays with the customer.

- 4 -
1200_GB-Inhalt_3552
TABLE OF CONTENTS
GB
Table of contents
WARNING SIGNS
CE sign ......................................................................5
Meaning of warning signs..........................................5
ATTACHING TO TRACTOR
Attaching in general...................................................6
Drive shaft..................................................................6
Attaching problems ...................................................6
Telescopic upper link.................................................6
Side protection ..........................................................7
Hydraulic side protection...........................................7
Transport width..........................................................8
Road Transport..........................................................8
Work position.............................................................8
Adjusting the floor bearing load of the mowing bar ..8
Pay particul arattention before initial attachment to
Tractor!.......................................................................9
Snap Connector (1)..................................................10
STARTING WORK
Safety hints..............................................................11
Mower drums direction of travel..............................12
Operation.................................................................12
Operation.................................................................13
Cutting height adjustment ......................................13
Cutting height adjustment .......................................13
SWATH FORMER
Operating Principle..................................................15
Adjustment Possibilities ..........................................15
Setting opitons for swath width...............................16
Non-standard equipment ........................................16
Maintenance ............................................................16
Montage of the transport-rings. ..............................17
Fitting inner conveying guides.................................17
MAINTENANCE
Safety point .............................................................18
General maintenance hints......................................18
Cleaning of machine parts.......................................18
Parking in the open..................................................18
Winter storage .........................................................18
Drive shafts..............................................................18
Hydraulic unit...........................................................18
Holder for a quick change of cutter blades.............19
Checking the mowing blade suspension.................19
Changing the Cutter Blades ....................................19
Cutters.....................................................................20
Mower disc ..............................................................20
Increased cutting height with high – cut mowing
plates .......................................................................21
Angular gear ............................................................21
TECHNICAL DATA
Technical data..........................................................22
Optional equipment .................................................22
Necessary connections ...........................................22
The defined use of the mower unit..........................23
Position of Vehicle Identification Plate ....................23
SUPPLEMENT
Recommendations for work safety .........................26
Driveshaft.................................................................28
Lubrication chart......................................................30
Lubricants................................................................32
Shorten upper link ...................................................34
Repairs on the cutter bar.........................................35
TAPER BUSHES
Taper bushes installation instructions .....................36
Combination of tractor and mounted implement ....37

- 5 -
9700_GB-Warnbilder_361
GB
WARNING SIGNS
Stay clear of swinging area of implements
Close both side protective coverings before engaging
p.t.o..
Never reach into the crushing danger area as long as
parts may move.
CE sign
The CE sign, which is affixed by the manufacturer, indicates outwardly that this machine
conforms to the engineering guideline regulations and the other relevant EU guidelines.
EU Declaration of Conformity (see supplement)
By signing the EU Declaration of Conformity, the manufacturer declares that the machine being
brought into service complies with all relevant safety and health requirements.
Meaning of warning signs
Danger - flying objects; keep safe distance from the
machine as long as the engine is running.
Wait until all machine components have stopped
completely before touching them.
Stay clear of mower knife area as long as tractor engine
is running with PTO connected.
Shut off engine and remove key before performing
maintenance or repair work.
Recommendations
for work safety
All points referring
to satety in this
manual are
indicated by this
sign.
bsb 447 410
495.167

- 6 -
1201-GB ANBAU-3552
GB
ATTACHING TO TRACTOR
When towing implements whose p.t.o stub is
positioned a long way forward, the drive shaft must
be shortened quite a bit.
• When the implement is engaged then there is
insufficient casing to over the drive shaft.
• The maximum angle of deviation of the universal-
joint will possibly be exceeded (see Supplement
B also).
In this case an
accessory kit
is necessary
which positions
the implement
approx.200 mm
forwards.
In a case such
as this please
contact our
Customer Service Dept.
Attaching problems
On lifting gear with a crosspiece (Q) between the lower
links, damage couldoccur to the drive shaftwhen lowering
the attached implement.
In order to prevent
damage an extra
elevator unit is to be
installed between the
Weiste-triangle and
the lifting gear.
In a case such as
this please contact
our Customer Service
Dept.
Attaching in general
1. Observe safety tips in supplement A.
2. Mark off the implement at the tractor's front lifting gear.
• Secure locking bolts with linch pins.
Drive shaft
• Before operating for the first time, drive shaft is to be
checked and adapted if necessary. See also chapter
"Fitting the drive shaft" in supplement B.
Attention!
The following
danger source
exists with double
action front lifting
devices on trac-
tors:
The maximum mo-
wer unit lowering
depth is set with
limiting chains.
If the lifting gear
exceeds the maxi-
mum set lowering
depth then load
is placed on the
limiting chains.
This can lead to the
chain or the linch
pin breaking and
danger of injury
exists for persons
standing in the
danger are!
Take note!
No support stands
are required to
securely park the
mowing unit with
swath former!
Telescopic upper link
The telescopic upper link enables mower drums to
adapt well to uneven ground surfaces that run across
the direction of travel.
- The swing range (L) can be adjusted by turning the
spindle.
- Shorten upper link, see supplement D

- 7 -
1201-GB ANBAU-3552
ATTACHING TO TRACTOR GB
Side protection
Guard plates and protective aprons can be raised when
maintenance work is to be done.
For safety reasons it is necessary to wait
for mowing disks to stop completely before
raising and securing guard plates.
1. Loosen locking mechanism (1) and swing
protection (2) up.
- engage protective frame in holder (3)
- left and right
3
1
2
Hydraulic side protection
Be aware!
Danger of crushing exists when swinging
side protection up!
As an optional extra, the side protection can be swung
up hydraulically using the tractor’s servo.
This would eliminate the necessity of releasing or latching
a locking device.
Solving problems with hydraulic connection
Hydraulic side protection requires a double-action
system. If tractor has no hydraulic connection at the
front, then two hydraulic hoses must be run from the
back to the front.
A switch between the front lifting gear (HW) and
front control device (SG) via a three-way tap may be
necessary with some tractors.
Beware!
Swing side protec-
tion down before
starting work!
Beware!
Check side protec-
tion for correct
function, working
position and
condition before
every operation.
Any defective parts
on the safety
equipment must
be replaced im-
mediately.
The manufacturer
is not responsible
for any manipula-
tion and inap-
propriate use of
safety equipment.
Beware!
Entering the safety
equipment area is
not permitted!
HW
SG

- 8 -
1201-GB ANBAU-3552
ATTACHING TO TRACTOR GB
Transport width
When both safety devices are swivelled up and secured
in the catch (3), the consequent width is:
EUROCAT 271
Type 3542 EUROCAT 311 Type 3552
Width (X) 2,65 m 3 m
Road Transport
• Observe the regulations issued by your country's
legislative body.
• Travelling on public roads may only be undertaken as
is described in the chapter "Transporting Position".
• Fasten lower hydraulic link so that implement cannot
swing out sideways.
Work position
Before commencing work
Turn the p.t.o. on only when all safety devices
(coverings, protective aprons, casings, etc.)
are in proper condition and attached to the
implement in the correct protective positions.
For safety reasons mowing may only be
conducted in this position.
495.167
Adjusting the floor bearing load of the
mowing bar
Adjusting hints
- The mowing bar should weigh 150kg resting on the
ground (75kg left and right).
As the total weight of the mowing unit is higher, a
corresponding weight relief must be set.
For this purpose, a mowing unit with swath discs is
equipped with two tension springs, which must be
pre-tensioned accordingly.
Setting of spring tension
1. Lift implement hydraulically
2. Hook tension spring on headstock arm (1) and on relief
spring bracket (20) to tractor.
3. Lower implement to the ground.
4. Using the chain, set spring tension for mower bar
ground pressure at approx. 150 kg (approx.75 kg left
and right).
5. The optimal force angle of 20 - 22o can only be
maintained when springs are secured to a bracket.
6. Slip the hose clamp (20) onto the tension spring.
Doing this means that spring tension does not have to
be checked every time unit is attached to tractor.
The set measurement of "L2" need only be checked
and, if necessary, adjusted when tractors are changed.
1
2
TD29/93/2
20

- 9 -
1200_GB-WEISTEANBAU-3552
SNAP CONNECTOR GB
Pay particul arattention before initial
attachment to Tractor!
Note!
For front lifting gear with double-action
hydraulic cycle (danger of damage)!
Remedy:
- Switch control valve to single-action
- Convert front lifting gear to single-action function
(bypass line) through a specialist work shop
• When the mower is attached to the tractor,
the the hydraulic control (ST) must not be
set at „Lower“.
• Immediately after such an operating error,
reset the adjustable plate (P1). Replace
damaged parts beforehand.
The following could happen after an operating error:
- the position of the plate (P1) has changed in the slot;
the gap to the locking hook (V) is therefore too great,
- the locking hook (V) breaks,
- both levers on the load relieving unit become
damaged.
- The limiting chains can snap.
Reset the adjustable plate (P1)
1. Loosen nut (SK) enough so that plate (P1) position can
be altered using setscrew (ST).
2. Couple the mower to the tractor´s lifting gear
3. Position the adjustable plate (P1) so that the locking
hook (V) can still be unlatched.The gap to the hook
should be as narrow as possible.
4. Uncouple the mower from the tractor´s lifting gear.
5. Tighten screws (SK) to 65 Nm.
ST-24-11-2003
Beware!
The following
danger source
exists with double
action front
lifting devices
on tractors: The
maximum mower
unit lowering
depth is set with
limiting chains.
If the lifting gear
exceeds the maxi-
mum set lowering
depth then load
is placed on the
limiting chains.
This can lead to the
chain or the linch
pin breaking and
danger of injury
exists for persons
standing in the
danger are!
V
P1
ST
SK

- 10 -
1200_GB-WEISTEANBAU-3552
SNAP CONNECTOR GB
Snap Connector (1)
1. Mount snap connector (Weiste triangle) onto the front
lifting gear in a vertical position or inclined slightly
forward.
2. Lock lower link bolts (2) so that they are free from play.
3. Connect and lift mower unit (H2).
4. Secure locking clamp (V) with cotter pin.
- Check the position of the adjustable plate (P1).
Thegap to the hookshouldbeasnarrowaspossible.
5. Fit drive shaft.
TD28/91/28
1
P1
V
V

- 11 -
1200-GB Einsatz_3552
GB
STARTING WORK
After any contact with foreign objects
• Check the condition of knives and the knife holder (see
chapter "Maintenance and service").
• Retighten all knife screw fittings.
• Carefully check the implement for damage. The
mowing discs and their drive shaft must be checked
in particulare.
• Have the implement checked also by a specialist
workshop if necessary.
5. Stay clear while engine is running.
- Keep people out of the danger zone - foreign bodies
which can be ejected by the mower could injure them.
Special care is necessary on or near stony ground.
6. Wear hearing protection
The noise level inthe workplacecan deviate
from the measured value (see Technical
Data) partly because of the differing cabin
types of various tractors.
• If a noise level of 85 dB (A) is reached or exceeded,
the farmer must have suitable hearing protection in
readiness (UVV 1.1 §2).
• If a noise level of 90 dB (A) is reached or exceeded,
the hearing protection must be worn (UVV 1.1 § 16).
Safety hints
1. Check:
- wear and tear on blade bolts (31). If bolt thickness is
< 9mm then exchange blade holder.
- blade holder (30) for damage.
- when grinding noises are heard, see if the blade holder
is bent causing the blade to sit incorrectly.
2. Switch-on the machine only in working position
and do not exceed the prescribed power take-
off speed (for example max. 540 rpm).
A transfer, which is located near the gear, advises which
p.t.o. speed your mower unit is equipped for.
• Turn the p.t.o.ononly whenallsafetydevices (coverings,
protective aprons, casings, etc.) are in proper condition
and attached to the implement in the correct protective
positions.
3. Pay attention to correct p.t.o.
direction of rotation!
4. Damage protection!
• The surface to be mowed must be free of
obstructions or foreign objects. Such objects
(e.g. large stones, pieces of wood, boundary
stones, etc.) can damage the mower unit.
In the event of a collision
• Stop immediately and switch off the drive.
• Carefully check the implement for damage. The
mowing discs and their drive shaft must be checked
in particulare.
• Have the implement checked also by a specialist
workshop if necessary.
bsb 447 410
TD8/95/6

- 12 -
1200-GB Einsatz_3552
GB
STARTING WORK
1)Only with disc mowing
Remedy, if the tractor’s power take-off shaft
drive cannot be switched to turn to the left:
- dismantle the transmission (G2), rotate by 180 degrees
and re-install
Important
points
before
starting work
Safety hints: see
supplement-A1
points 1. - 7.)
General
For mowing, the power take-off shaft drive should be
switched to turn to the left.
Operation
Take note!
Check all safety equipment!
Stones and other objects can be picked
up and thrown out when mowing. Direct
people out of the danger area.
Side protection must be properly swivelled
down and secured!
1. Set cutting height by installing/removing
spacers
2. To mow, slowly throw in the p.t.o. away from
the mowing area and bring the mowing rotor
up to full speed.
Smoothly increase the p.t.o. speed, in order to avoid
noises in the free-wheel conditioned by the system.
- Adjust travel speed to terrain and crop.
Mower drums direction of travel
After the first hours
of operation
• Retighten all kni-
fe screw fittings.
TD40/94/16
TD 79/98/53
G2
The mower drums direction of travel is OK if the outside
drum is turning inward when looking from the front.
R
L
TD28/91/21

- 13 -
1200-GB Schnitthöhe_3552
GB
STARTING WORK
Operation
1. Adjust cutting height by turning upper link spindle
(inclination of the cutting discs max. 5°).
Cutting height adjustment
The cutting height can be set anywhere from 35 to 65 mm by adjusting
the centre disc.
1. Lift unit with loader (~5 cm).
2. The key (W) is put on the square or hexagon and turned until the
required cutting height is set.
Turn once = 1,5 mm
Cutting height adjustment
Safety points
- Turn engine off when
adjustment, service and
repair work is to be done.
- Do not work under the
machine without safe
support.
- Retighten all screws after
the first hours of operation.
Distance plates
• The cutting height is set by inserting distance plates (4mm,
6mm).
2 of which have already been inserted (4mm, 6mm) in the
factory.
Optional equipment: 8 distance plates (6mm)
Optional equipment: high-cut mowing plate (H1)
• Each mowing drum must have an equal number of plates
inserted.
Inserting distance plates
1. Remove both skide plates (S1, 1a).
2. Insert distance plates (6mm).
3. Refit both skid plates.
Replace worn or damaged spring lock washers with new ones.
Similarly with worn screws and nuts.
Tighten all screws firmly!
4. Check after the first hour of operation
Check all screws for tightness.
TD 79/99/10
~ 5cm
TD 79/99/05

- 14 -
1200-GB Schnitthöhe_3552
GB
STARTING WORK

Operating Principle
A narrow swath is formed when using the swath plates while mowing. This avoids driving over the crop with wide tractor
tyres.
Warning!
Rotating parts,
danger of being
pulled in. Never
open or remove
protective devices
when engine is
running.
Safety note:
Read and comply
with the Opera-
ting Instructions
and particularly
the safety notes
prior to commis-
sioning.
Designations:
(1) Swath disc holder
(2) Swath disc
(3) Adjusting mechanism
Adjustment Possibilities
1
2
3
Working range:
1. Swath former height can be set via the elongated holes
(1).
Optimum setting:
The discs are fitted 5-10mm higher than the swath
plate lower edge.
2. Distance to mowing drums can be adjusted using
screws (2)
3. Swath disc incline can be adjusted using screws (3).
The factory sets the catches (4) one behind the other
as shown in the diagram.
1
3
2
4
5 - 10mm
5 - 10mm
- 15 -
1201-GB_SCHWADFORMER_3552
GB
SWATH FORMER

Non-standard equipment
Additional swath plate
Adjusting the two tension springs:
A = For tall, dense fodder crops.
B = Basic setting.
C= For short fodder crops.
Maintenance
The swath former is maintenance-free with the exception of cleaning activities.
Caution!
Switch off the engi-
ne before carrying
out maintenance
and repair work
and remove the
ignition key.
073-12-01
Setting opitons for swath width
Setting the swath width:
The swath discs form the fodder into the required swath
width. Swath discs are set individually left and right using
the regulating lever (E).
Setting the swath disc position
Thesettings listed belowshouldbetaken as basicsettings.
An optimum swath disc setting could be possible when
actually in operation, conditional to the various fodder
types.
Wide spreading
- Swing swath discs completely out
- Position (B)
Swaths
- Swing swath discs completely in
- Position (L)
B
L
E
- 16 -
1201-GB_SCHWADFORMER_3552
SWATH FORMER GB

Montage of the transport-rings.
Additionaltransport-rings can befittedtothe inner mowing
drumstopreventcloggingwhenworkingwithdensefodder.
Adjustment "8 - 10 cm"
Attention!
Transport rings cannot be used together
with a conditioner!
Fitting inner conveying guides
(Only available for Eurocat 311 classic)
For dense fodder additional conveying guides can be
fitted to prevent clogging
Attention!
Conveying guides cannot be used together
with a conditioner!
- 17 -
1201-GB_SCHWADFORMER_3552
SWATH FORMER GB

- 18 -
GB
1201_GB-Allgemeine-Wartung_BA
Parking in the open
When parking in the open for
long periods oftime,cleanpiston
rods and then coat with grease.
FETT
TD 49/93/2
Safety points!
• Turn engine off
when adjustment,
service and repair
work is to be
done.
• Do not work un-
der the machine
without safe
support.
• Retighten all
screws after the
first hours of
operation.
• Only place the
machine on an
even, firm ground.
Cleaning of machine parts
Attention! Do not use high-pressure washers for the
cleaning of bearing- and hydraulic parts.
- Danger of rust!
- After cleaning, grease the machine according to the
lubrication chart and carry out a short test run.
- Cleaning with too high pressure may do damage to
varnish.
Safety point
• Turn engine off when adjustment, service and repair
work is to be done.
Hydraulic unit
Caution! Danger of injury or infection!
Under high pressure, escaping fluids can penetrate
the skin. Therefore seek immediate medical help!
Make sure that the hydraulic system is suitable for the
tractor before connecting the hydraulic lines.
After the first 10 operating hours and then every
consecutive 50 operating hours
- Check the hydraulic unit and lines for tightness and
retighten screw connections if necessary.
Before operation
- Check hydraulic hoses for wear.
Replace worn or damaged hydraulichosesimmediately.
The replacement hoses must meet the manufacturer’s
technical requirements.
Hose lines are subject to natural ageing. The period of
use should not exceed 5 – 6 years.
Winter storage
- Thoroughly clean machine before storage.
- Put up protection against weather.
- Change or replenish gear oil.
- Protect exposed parts from rust.
- Lubricate all greasing points according to lubrication
chart.
Drive shafts
- see notes in the supplement
For maintenance please note!
The instructions in this operating manual are always
valid.
In case there are no special instructions available, then
the notes inthe accompanyingdriveshaft manufacturer´
instructions are valid.
Repair Instructions
Please refer to
repair instructions
in supplement (if
available)
Safety points!
Clean the hydraulic
line couplings and
the oil connec-
tions each time
before coupling.
Check for chafing
and jamming
points.
MAINTENANCE
General maintenance hints
In order to keep the implement in
good condition after long periods
of operation, please observe the
following points:
- Tighten all screws after the first
hours of operation.
In particular check:
- blade screws on the mowers
- tine screws on the swather and tedder.
Spare part
a. The original components and accessories have been
designedespecially for these machines andappliances.
b. We want to make it quite clear that components and
accesories that have not been supplied by us have not
been tested by us.
c. The installation and/or use of such products can,
therefore, negatively change or influence the
construction characteristics ofthe appliance.We are not
liable for damages caused by the use of components
and accessories that have not been supplied by us.
d. Alterations and the use of auxiliary parts that are not
permitted by the manufacturer render all liability invalid.

- 19 -
1000_GB-WARTUNG_344
MAINTENANCE AND SERVICE GB
Changing the Cutter Blades
1. Prop up the lever (29) on the lower edge of
the drum and push the moveable holder (30)
downwards.
- The cutter (14) is hung on the bolt (31).
2. Remove cutter blade (14)
3. Clean forage remains and dirt away.
- around the
bolts (31)
4. Check:
• blade bolts (31) for
damage, wear and
fitting
• holder (30) for
damage, change in
position and fitting
5. Fit cutter blades and remove lever (29)
• Place lever (29) into the 2 U – holder.
Holder for a quick change of cutter
blades
Attention!
For Your Safety
- Regularly check that cutter blades are tightened firmly!
- Cutter blades on a cutter disc should wear out
simultaneously (danger of imbalance).
Otherwise they are to be replaced with new ones
(replace in pairs).
- Buckled or damaged cutter blades must not be
used further.
• Buckled, damaged and/or worn cutter blade holders
(30) must not be used further.
Checking the mowing blade suspension
- Normal check every 50 hours.
- Check regularly when mowing on stony terrain or under
other difficult operating conditions.
- Check immediately after driving over a hard obstacle
(e.g. stones pieces of wood, ect).
Carry out a check
- as described in chapter „Changing the Cutter Blades“
Take note!
Damaged, buckled and worn out parts must
not be used further (danger of accident).
TD 79-99-03
31
30
14
29

- 20 -
1000_GB-WARTUNG_344
MAINTENANCE AND SERVICE GB
Cutters
The cutters on a cutting drum should be
evenly worn out, (danger of imbalance)
otherwise they are to be replaced by new
ones.
Pay attention to correct assembly!
- Cutters with the notation “L” are only to be mounted
on the left rotating mowing drum.
- Cutters with the notation “R” are only to be mounted
on the right rotating mowing drum.
Mower disc
With mower discs that are worn in the mowing blade area,
you must proceed as follows:
• Remove both bottom skid plates (S1, S2).
• Remove screws from knife guide (30).
• Move knife guide approx. 60°.
• Tighten screws firmly (120Nm).
- check for tightness after several hours of operation.
• Refit both bottom skid plates properly.
R
L
TD28/91/21
119-01-21
120 Nm
(12 kpm) 30
S2
S1
M
119-01-22