Prevue Hendryx 3451 User manual

CUSTOMER SUPPORT
For assistanc or r plac m nt parts,
pl as contact Pr vu P t Products:
PHONE [phone]
ONLINE www.pr vu p t.com
EMAIL cu tomer ervice @ prevuepet.com
3451
MODEL #
3451—10/18—USL Made in China for Prevue Pet Produ ts, In ., 224 N Maplewood Ave, Chi ago IL 60612 USA • 1 [312] 243-3624 • www.prevuepet. om • ustomerservi e @ prevuepet. om
St inless Steel
Pl ytop Home
PARTS LIST
Instructions onlin at www.pr vu p t.com
]Pc
]Cc
]Ls
]Rs
]R
]B
]F
Phillips-he d screws
18 pcs (inst lled in pl ce
on c ge p nels) *
Hex screws
4 pcs (inst lled in pl ce
on pl ytop supports)
Knobs
4 pcs (inst lled in pl ce
on c ge & pl ytop b r)
* (plus 2 b gged extr s)
]C
C sters
4 pcs
HARDWARE
INCLUDED:
TOOLS
INCLUDED:
KEY:
B = Back pan l
LS = L ft Sid pan l
F = Front pan l
RS = Right Sid pan l
R = Roof grill
C = Cast rs
PC = Playtop Compon nts
CC = Cag Compon nts
Allen wrench
TOOLS NOT
INCLUDED:
Phillips-he d
screwdriver

KEY:
B = Back pan l
F = Front pan l
LS = L ft sid
pan l
RS = Right sid
pan l
R = Roof grill
C = Cast rs
CC = Cag
Compon nts
PC = Playtop
Compon nts
CUSTOMER SUPPORT
For assistanc or r plac m nt parts,
pl as contact Pr vu P t Products:
PHONE [phone]
ONLINE www.pr vu p t.com
EMAIL cu tomer ervice @ prevuepet.com
34 51— 10 /18— USL Made in China for Prevue Pet Produ ts, In ., 224 N Maplewood Ave, Chi ago IL 60612 USA • 1 [312] 243-3624 • www.prevuepet. om • ustomerservi e @ prevuepet. om
Instructions onlin at www.pr vu p t.com
TOOLS NEEDED : Phillips h ad scr wdriv r • For b st r sults, follow Ass mbly St ps in ord r pr s nt d.
2PIECES
3451 St inless Steel
Pl ytop Home
MODEL #
]R
]B
]Ls
]Rs
]F
]C
Screw are in talled in place. When attaching panel or component ,
back the crew out, match up the component , and rein ert to attach.
⁕
In mo t ca e , we recommend
two people a emble thi cage.
⁕
While the lockable rolling
casters can be added at
any point in the a embly,
we recommend in talling
them at thi time.
Screw the threaded ca ter
po t into the frame leg at
each corner. If preferred,
tighten each ca ter with a
lim wrench.
Back the Phillip -head crew out,
align the side panel with the front
panel, and re-tighten the crew to
attach.
Repeat thi method for
all panel to a emble
the cage body.
Note: Small loop on
the back panel should
face the interior. This
loop helps hold the
bottom grille in place.
Set the cage roof grille in
place and attach with the
Phillip -head crew .
1PIECES

]Cc
3451—10/18— USL For more wonderful ages, toys, and a essories for dogs, ats, birds, hi kens, rabbits, ferrets and small animals, visit www.prevuepet. om
3PIECES
Ass mbly compl t d. {
4PIECES
]Pc
Cups/cup holders:
Open the cup door.
In ert the crew po t
on the cup holder
through the door me h,
add the bracket on the
out ide, and tighten to
the door with the
wing nut .
Place the deep cup
into the holder .
Grille and tray:
Open the grille lock.
Slide the grille
(with handle) into
the top channel and
the deep tray into
the bottom channel.
Perch:
Hold the perch in place in the cage interior.
In tall a Phillip -head crew through the
bracket, through the cage wire, into the
perch bracket and tighten with a Phillip
crewdriver for all four crew .
Back the Phillip -head crew out
on the under ide of the perch bar
and attach the cup holder .
Loo en the knob crew on
the perch bar rail and along the
cage front. In ert the ladder and
re-tighten the knob crew .
Attach the perch bar to the
upport rail u ing the hex crew
and the allen wrench.
In ert the hallow cup .
Open the grille lock. Slide the
thin grille into the top channel
and the shallow tray into the
bottom channel.
Remove the hex crew from the
end of the perch bar upport .
In tall the perch bar upport on
the back panel of the cage.
When fully a embled, check and tighten
ALL crew and wing nut over the entire cage
to en ure a afe and table home.
⁕